AT89C5131A-S3SIM

AT89C5131A-S3SIM Datasheet

AT89C5130A-M AT89C5131A-M

Part	Datasheet
AT89C5131A-S3SIM	AT89C5131A-S3SIM (pdf)

Related Parts	Information
AT89C5130A-RDTIM	AT89C5130A-RDTIM

PDF Datasheet Preview
• 80C52X2 Core 6 Clocks per Instruction Maximum Core Frequency 48 MHz in X1 Mode, 24 MHz in X2 Mode Dual Data Pointer Full-duplex Enhanced UART EUART Three 16-bit Timer/Counters T0, T1 and T2 256 Bytes of Scratchpad RAM • 16/32-Kbyte On-chip Flash In-System Programming through USB Byte and Page 128 bytes Erase and Write 100k Write Cycles • 4-Kbyte EEPROM for Bootloader 3-Kbyte and Data 1-Kbyte Byte and Page 128 bytes Erase and Write 100k Write Cycles • On-chip Expanded RAM ERAM 1024 Bytes • Integrated Power Monitor POR/PFD to Supervise Internal Power Supply • USB and Full Speed Compliant Module with Interrupt on Transfer Completion Endpoint 0 for Control Transfers 32-byte FIFO 6 Programmable Endpoints with In or Out Directions and with Bulk, Interrupt or Isochronous Transfers Endpoint 1, 2, 3 32-byte FIFO Endpoint 4, 5 2 x 64-byte FIFO with Double Buffering Ping-pong Mode Endpoint 6 2 x 512-byte FIFO with Double Buffering Ping-pong Mode Suspend/Resume Interrupts 48 MHz PLL for Full-speed Bus Operation Bus Disconnection on Microcontroller Request • 5 Channels Programmable Counter Array PCA with 16-bit Counter, High-speed Output, Compare/Capture, PWM and Watchdog Timer Capabilities • Programmable Hardware Watchdog Timer One-time Enabled with Reset-out 100 ms to 3s at 8 MHz • Keyboard Interrupt Interface on Port P1 8 Bits • TWI Two Wire Interface 400Kbit/s • SPI Interface Master/Slave Mode • 34 I/O Pins • 4 Direct-drive LED Outputs with Programmable Current Sources 2-6-10 mA Typical • 4-level Priority Interrupt System 11 sources • Idle and Power-down Modes • 0 to 24 MHz On-chip Oscillator with Analog PLL for 48 MHz Synthesis • Industrial Temperature Range • Extended Range Power Supply 2.7V to 5.5V 3.3V to 5.5V required for USB • Packages PLCC52, VQFP64, QFN32 8-bit Flash Microcontroller with Full Speed USB Device AT89C5130A-M AT89C5131A-M AT89C5130A/31A-M is a high-performance Flash version of the 80C51 single-chip 8-bit microcontrollers with full speed USB functions. AT89C5130A/31A-M features a full-speed USB module compatible with the USB specifications Version and This module integrates the USB transceivers with a 3.3V voltage regulator and the Serial Interface Engine SIE with Digital Phase Locked Loop and 48 MHz clock recovery. USB Event detection logic Reset and Suspend/Resume and FIFO buffers supporting the mandatory control Endpoint EP0 and up to 6 versatile Endpoints EP1/EP2/EP3/EP4/EP5/EP6 with minimum software overhead are also part of the USB module. AT89C5130A/31A-M retains the features of the Atmel 80C52 with extended Flash capacity 16/32-Kbytes , 256 bytes of internal RAM, a 4-level interrupt system, two 16bit timer/counters T0/T1 , a full duplex enhanced UART EUART and an on-chip oscillator. In addition, AT89C5130A/31A-M has an on-chip expanded RAM of 1024 bytes ERAM , a dual data pointer, a 16-bit up/down Timer T2 , a Programmable Counter Array PCA , up to 4 programmable LED current sources, a programmable hardware watchdog and a power-on reset. AT89C5130A/31A-M has two software-selectable modes of reduced activity for further reduction in power consumption. In the idle mode the CPU is frozen while the timers, the serial ports and the interrupt system are still operating. In the power-down mode the RAM is saved, the peripheral clock is frozen, but the device has full wake-up capability through USB events or external interrupts. 2 AT89C5130A/31A-M Block Diagram AT89C5130A/31A-M RxD TxD VDD VSS ECI CEX T2EX T2 SCL SDA MISO MOSI SCK XTAL1 XTAL2 ALE PSEN EA RD 2 WR 2 EEPROM ERAM EUART + RAM 16/32Kx8Flash 256x8 4Kx8 1Kx8 PCA Timer2 TWI C51 CORE Timer 0 INT Timer 1 Ctrl Parallel I/O Ports & Ext. Bus Port 0Port 1 Port 2 Port 3 Port 4 Key Board Watch Dog Regu- lator VREF RST T0 T1 INT0 INT1 P0 P1 P2 P3 P4 KIN DD+ AVSS AVDD Notes Alternate function of Port 1 Alternate function of Port 3 Alternate function of Port 4 Pinout Description Ordering Information Table Possible Order Entries Memory Size Kbytes AT89C5130A-RDTIM AT89C5130A-PUTIM AT89C5130A-S3SIM AT89C5131A-RDTIM AT89C5131A-PUTIM AT89C5131A-S3SIM Supply Voltage to 5.5V to 5.5V to 5.5V to 5.5V to 5.5V to 5.5V Temperature Range Industrial Package VQFP64 QFN32 PLCC52 VQFP64 QFN32 PLCC52 Packing Tray Stick Tray Stick AT89C5130A-RDTUM to 5.5V Industrial & Green AT89C5130A-PUTUM to 5.5V Industrial & Green AT89C5130A-S3SUM to 5.5V Industrial & Green AT89C5131A-RDTUM to 5.5V Industrial & Green AT89C5131A-PUTUM to 5.5V Industrial & Green AT89C5131A-S3SUM to 5.5V Industrial & Green Optional Packing and Package options please consult Atmel sales representative -Tape and Reel -Dry Pack -Die form VQFP64 QFN32 PLCC52 VQFP64 QFN32 PLCC52 Tray & Dry Pack Tray & Dry Pack Tray & Dry Pack Tray & Dry Pack Tray & Dry Pack Tray & Dry Pack Packaging Information 64-lead VQFP Ordering Information 179 Packaging Information 180 64-lead 181 52-lead PLCC 182 32-lead QFN 183 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel 1 408 441-0311 Fax 1 408 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel 41 26-426-5555 Fax 41 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel 852 2721-9778 Fax 852 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel 81 3-3523-3551 Fax 81 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel 1 408 441-0311 Fax 1 408 436-4314 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel 1 408 441-0311 Fax 1 408 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel 33 2-40-18-18-18 Fax 33 2-40-18-19-60 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel 33 4-42-53-60-00 Fax 33 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel 1 719 576-3300 Fax 1 719 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel 44 1355-803-000 Fax 44 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel 49 71-31-67-0 Fax 49 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel 1 719 576-3300 Fax 1 719 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel 33 4-76-58-30-00 Fax 33 4-76-58-34-80 Literature Requests Disclaimer The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise,to anyintellectualproperty right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORYWARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULARPURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-TAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ARISING OUTOF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes norepresentationsor warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specificationsand product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for useas components in applications intended to support or sustainlife. Atmel Corporation All rights reserved. logo and combinations thereof, are registered trademarks, and Everywhere You are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper.

PDF Datasheet Preview

• 80C52X2 Core 6 Clocks per Instruction Maximum Core Frequency 48 MHz in X1 Mode, 24 MHz in X2 Mode Dual Data Pointer Full-duplex Enhanced UART EUART Three 16-bit Timer/Counters T0, T1 and T2 256 Bytes of Scratchpad RAM
• 16/32-Kbyte On-chip Flash In-System Programming through USB Byte and Page 128 bytes Erase and Write 100k Write Cycles
• 4-Kbyte EEPROM for Bootloader 3-Kbyte and Data 1-Kbyte Byte and Page 128 bytes Erase and Write 100k Write Cycles
• On-chip Expanded RAM ERAM 1024 Bytes
• Integrated Power Monitor POR/PFD to Supervise Internal Power Supply
• USB and Full Speed Compliant Module with Interrupt on Transfer Completion

Endpoint 0 for Control Transfers 32-byte FIFO 6 Programmable Endpoints with In or Out Directions and with Bulk, Interrupt or

Isochronous Transfers Endpoint 1, 2, 3 32-byte FIFO Endpoint 4, 5 2 x 64-byte FIFO with Double Buffering Ping-pong Mode Endpoint 6 2 x 512-byte FIFO with Double Buffering Ping-pong Mode

Suspend/Resume Interrupts 48 MHz PLL for Full-speed Bus Operation Bus Disconnection on Microcontroller Request
• 5 Channels Programmable Counter Array PCA with 16-bit Counter, High-speed Output, Compare/Capture, PWM and Watchdog Timer Capabilities
• Programmable Hardware Watchdog Timer One-time Enabled with Reset-out 100 ms to 3s at 8 MHz
• Keyboard Interrupt Interface on Port P1 8 Bits
• TWI Two Wire Interface 400Kbit/s
• SPI Interface Master/Slave Mode
• 34 I/O Pins
• 4 Direct-drive LED Outputs with Programmable Current Sources 2-6-10 mA Typical
• 4-level Priority Interrupt System 11 sources
• Idle and Power-down Modes
• 0 to 24 MHz On-chip Oscillator with Analog PLL for 48 MHz Synthesis
• Industrial Temperature Range
• Extended Range Power Supply 2.7V to 5.5V 3.3V to 5.5V required for USB
• Packages PLCC52, VQFP64, QFN32
8-bit Flash Microcontroller with Full Speed USB Device

AT89C5130A-M AT89C5131A-M

AT89C5130A/31A-M is a high-performance Flash version of the 80C51 single-chip 8-bit microcontrollers with full speed USB functions.

AT89C5130A/31A-M features a full-speed USB module compatible with the USB specifications Version and This module integrates the USB transceivers with a 3.3V voltage regulator and the Serial Interface Engine SIE with Digital Phase Locked Loop and 48 MHz clock recovery. USB Event detection logic Reset and Suspend/Resume and FIFO buffers supporting the mandatory control Endpoint EP0 and up to 6 versatile Endpoints EP1/EP2/EP3/EP4/EP5/EP6 with minimum software overhead are also part of the USB module.

AT89C5130A/31A-M retains the features of the Atmel 80C52 with extended Flash capacity 16/32-Kbytes , 256 bytes of internal RAM, a 4-level interrupt system, two 16bit timer/counters T0/T1 , a full duplex enhanced UART EUART and an on-chip oscillator.

In addition, AT89C5130A/31A-M has an on-chip expanded RAM of 1024 bytes ERAM , a dual data pointer, a 16-bit up/down Timer T2 , a Programmable Counter Array PCA , up to 4 programmable LED current sources, a programmable hardware watchdog and a power-on reset.

AT89C5130A/31A-M has two software-selectable modes of reduced activity for further reduction in power consumption. In the idle mode the CPU is frozen while the timers, the serial ports and the interrupt system are still operating. In the power-down mode the RAM is saved, the peripheral clock is frozen, but the device has full wake-up capability through USB events or external interrupts.
2 AT89C5130A/31A-M

Block Diagram

AT89C5130A/31A-M

RxD TxD VDD VSS ECI CEX T2EX T2 SCL SDA

MISO MOSI SCK

XTAL1 XTAL2

ALE PSEN

EA RD 2 WR 2

EEPROM ERAM

EUART +

RAM 16/32Kx8Flash 256x8
4Kx8
1Kx8

PCA Timer2 TWI

C51 CORE

Timer 0 INT Timer 1 Ctrl

Parallel I/O Ports & Ext. Bus Port 0Port 1 Port 2 Port 3 Port 4

Key Board

Watch Dog

Regu-
lator

VREF

RST T0 T1

INT0 INT1

P0 P1 P2 P3 P4 KIN DD+ AVSS AVDD

Notes Alternate function of Port 1 Alternate function of Port 3 Alternate function of Port 4

Pinout Description
Ordering Information

Table Possible Order Entries

Memory Size Kbytes

AT89C5130A-RDTIM

AT89C5130A-PUTIM

AT89C5130A-S3SIM

AT89C5131A-RDTIM

AT89C5131A-PUTIM

AT89C5131A-S3SIM

Supply Voltage to 5.5V to 5.5V to 5.5V to 5.5V to 5.5V to 5.5V

Temperature Range Industrial

Package VQFP64 QFN32 PLCC52 VQFP64 QFN32 PLCC52

Packing Tray Stick Tray Stick

AT89C5130A-RDTUM
to 5.5V

Industrial & Green

AT89C5130A-PUTUM
to 5.5V

Industrial & Green

AT89C5130A-S3SUM
to 5.5V

Industrial & Green

AT89C5131A-RDTUM
to 5.5V

Industrial & Green

AT89C5131A-PUTUM
to 5.5V

Industrial & Green

AT89C5131A-S3SUM
to 5.5V

Industrial & Green

Optional Packing and Package options please consult Atmel sales representative -Tape and Reel -Dry Pack -Die form

VQFP64 QFN32 PLCC52 VQFP64 QFN32 PLCC52

Tray & Dry Pack

Tray & Dry Pack

Tray & Dry Pack

Tray & Dry Pack

Tray & Dry Pack

Tray & Dry Pack

Packaging Information
64-lead VQFP
Ordering Information 179 Packaging Information 180
64-lead 181 52-lead PLCC 182 32-lead QFN 183

Atmel Corporation
2325 Orchard Parkway San Jose, CA 95131, USA Tel 1 408 441-0311 Fax 1 408 487-2600

Regional Headquarters

Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel 41 26-426-5555 Fax 41 26-426-5500

Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel 852 2721-9778 Fax 852 2722-1369

Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel 81 3-3523-3551 Fax 81 3-3523-7581

Atmel Operations

Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel 1 408 441-0311 Fax 1 408 436-4314

Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel 1 408 441-0311 Fax 1 408 436-4314

La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel 33 2-40-18-18-18 Fax 33 2-40-18-19-60

ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel 33 4-42-53-60-00 Fax 33 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel 1 719 576-3300 Fax 1 719 540-1759

Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel 44 1355-803-000 Fax 44 1355-242-743

RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel 49 71-31-67-0 Fax 49 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel 1 719 576-3300 Fax 1 719 540-1759

Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom

Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel 33 4-76-58-30-00 Fax 33 4-76-58-34-80

Literature Requests

Disclaimer The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise,to anyintellectualproperty right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORYWARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULARPURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-TAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ARISING OUTOF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes norepresentationsor warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specificationsand product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for useas components in applications intended to support or sustainlife.

Atmel Corporation All rights reserved. logo and combinations thereof, are registered trademarks, and Everywhere You are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.

Printed on recycled paper.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT89C5131A-S3SIM Datasheet file may be downloaded here without warranties.

Datasheet ID: AT89C5131A-S3SIM 519081