MX25V8006EZNI-13G

MX25V8006EZNI-13G Datasheet

MX25V8006E

Part	Datasheet
MX25V8006EZNI-13G	MX25V8006EZNI-13G (pdf)

Related Parts	Information
MX25V8006EM1I-13G	MX25V8006EM1I-13G

PDF Datasheet Preview
MX25V8006E MX25V8006E DATASHEET P/N PM1646 MX25V8006E Contents 4 GENERAL 5 PIN 5 PIN 5 BLOCK 6 MEMORY 7 Table Memory 7 DEVICE 8 Figure Serial Peripheral Interface Modes 8 DATA 9 Table Protected Area 9 Table 512 bit Secured OTP 10 HOLD 11 Figure Hold Condition Operation Table COMMAND 12 COMMAND 13 1 Write Enable 13 2 Write Disable 13 3 Read Status Register 14 4 Write Status Register 15 Table Protection 15 5 Read Data Bytes 16 6 Read Data Bytes at Higher Speed 16 7 Dual Output Mode 16 8 Sector Erase 16 9 Block Erase 17 10 Chip Erase 17 11 Page Program 17 12 Deep Power-down 18 13 Release from Deep Power-down RDP , Read Electronic Signature RES 18 14 Read Identification 19 15 Read Electronic Manufacturer ID & Device ID 19 Table ID 19 16 Enter Secured OTP 19 17 Exit Secured OTP 19 18 Read Security Register 20 Table SECURITY REGISTER 20 19 Write Security Register 20 Read SFDP Mode 21 Read Serial Flash Discoverable Parameter RDSFDP 21 Table a. Signature and Parameter Identification Data Values 22 Table b. Parameter Table 0 JEDEC Flash Parameter 23 Table c. Parameter Table 1 Macronix Flash Parameter 25 P/N PM1646 MX25V8006E POWER-ON 27 ELECTRICAL 28 P/N PM1646 MX25V8006E 8M-BIT [x 1/x 2] CMOS SERIAL FLASH GENERAL • Serial Peripheral Interface compatible -- Mode 0 and Mode 3 • 8,388,608 x 1 bit structure or 4,194,304 x 2 bits Dual Output mode structure • 256 Equal Sectors with 4K byte each - Any Sector can be erased individually • 16 Equal Blocks with 64K byte each - Any Block can be erased individually • Program Capability - Byte base - Page base 256bytes • Single Power Supply Operation - to volt for read, erase, and program operations • Latch-up protected to 100mA from -1V to Vcc +1V PERFORMANCE • High Performance - Fast access time 75MHz serial clock - Serial clock of Dual Output mode 70MHz - Fast program time 1.4ms typ. and 5ms max. /page 256-byte per page - Byte program time 9us - Fast erase time 60ms typ. /sector 4K-byte per sector 0.7s typ. /block 64K-byte per block • Low Power Consumption - Low active read current 12mA max. at 75MHz and 4mA max. at 33MHz - Low active programming current 20mA max. - Low active erase current 20mA max. - Low standby current 25uA max. - Deep power-down mode 5uA typ. • Minimum 100,000 erase/program cycles • 20 years data retention SOFTWARE FEATURES • Input Data Format - 1-byte Command code • Advanced Security Features - Block lock protection The BP2-BP0 status bit defines the size of the area to be software protection against program and erase instructions - Additional 512 bit secured OTP for unique identifier • Auto Erase and Auto Program Algorithm - Automatically erases and verifies data at selected sector - Automatically programs and verifies data at selected page by an internal algorithm that automatically times the program pulse widths Any page to be programed should have page in the erased state first • Status Register Feature • Electronic Identification - JEDEC 1-byte manufacturer ID and 2-byte device ID - RES command for 1-byte Device ID - REMS command for 1-byte manufacturer ID and 1-byte device ID • Support Serial Flash Discoverable Parameters SFDP mode HARDWARE FEATURES • PACKAGE - 8-pin SOP 150mil - 8-land WSON 6x5mm, 0.8mm package height - All devices are RoHS Compliant P/N PM1646 MX25V8006E The device features a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus. The four bus signals are a clock input SCLK , a serial data input SI , a serial data output SO , and a chip select CS# . Serial access to the device is enabled by CS# input. When it is in Dual Output read mode, the SI and SO pins become SIO0 and SIO1 pins for data output. The device provides sequential read operation on whole chip. After program/erase command is issued, auto program/erase algorithms which program/erase and verify the specified page or sector/block locations will be executed. Program command is executed on byte basis, or page basis, or word basis for erase command is executes on sector, or block, or whole chip basis. To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read command can be issued to detect completion status of a program or erase operation via WIP bit. When the device is not in operation and CS# is high, it is put in standby mode. The device utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after 100,000 program and erase cycles. PIN CONFIGURATIONS 8-PIN SOP 150mil CS# 1 SO/SIO1 2 WP# 3 GND 4 8 VCC 7 HOLD# 6 SCLK 5 SI/SIO0 8-LAND, WSON 6x5mm CS# 1 SO/SIO1 2 WP# 3 GND 4 8 VCC 7 HOLD# 6 SCLK 5 SI/SIO0 PIN DESCRIPTION SYMBOL DESCRIPTION CS# Chip Select SI/SIO0 Serial Data Input for 1 x I/O / Serial Data Input & Output for Dual Output mode ORDERING INFORMATION PART NO. MX25V8006EM1I-13G MX25V8006EZNI-13G CLOCK MHz OPERATING CURRENT mA STANDBY CURRENT uA Temperature Package -40~85°C 8-SOP 150mil -40~85°C 8-land WSON 6x5mm Remark P/N PM1646 MX25V8006E PART NAME DESCRIPTION MX 25 V 8006E M1 I OPTION G RoHS Compliant SPEED 13 75MHz TEMPERATURE RANGE I Industrial -40°C to 85°C PACKAGE ZN WSON 0.8mm package height M1 150mil 8-SOP DENSITY & MODE 8006E 8Mb TYPE V 2.5V DEVICE 25 Serial Flash P/N PM1646 PACKAGE INFORMATION MX25V8006E P/N PM1646 MX25V8006E P/N PM1646 MX25V8006E Updated VWI value. Removed Advanced Information. Modified Figure Write Security Register WRSCUR Sequence Added Read SFDP RDSFDP Mode Page P26 Date 2010/12/15 P28,40 JAN/24/2011 P38 P4,8,12, FEB/10/2012 P21~26,31 P/N PM1646 MX25V8006E Except for customized products which has been expressly identified in the applicable agreement, Macronix's products are designed, developed, and/or manufactured for ordinary business, industrial, personal, and/or household applications only, and not for use in any applications which may, directly or indirectly, cause death, personal injury, or severe property damages. In the event Macronix products are used in contradicted to their target usage above, the buyer shall take any and all actions to ensure said Macronix's product qualified for its actual use in accordance with the applicable laws and regulations and Macronix as well as it’s suppliers and/or distributors shall be released from any and all liability arisen therefrom. Copyright Macronix International Co., Ltd. All rights reserved, including the trademarks and tradename thereof, such as Macronix, MXIC, MXIC Logo, MX Logo, Integrated Solutions Provider, NBit, Nbit, NBiit, Macronix NBit, eLiteFlash, XtraROM, Phines, KH Logo, BE-SONOS, KSMC, Kingtech, MXSMIO, Macronix vEE, Macronix MAP, Rich Audio, Rich Book, Rich TV, and FitCAM. The names and brands of other companies are for identification purposes only and may be claimed as the property of the respective companies. For the contact and order information, please visit Macronix’s Web site at: MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice. 52

PDF Datasheet Preview

MX25V8006E

MX25V8006E DATASHEET

P/N PM1646

MX25V8006E

Contents
4 GENERAL 5 PIN 5 PIN 5 BLOCK 6 MEMORY 7

Table Memory 7 DEVICE 8

Figure Serial Peripheral Interface Modes 8 DATA 9

Table Protected Area 9 Table 512 bit Secured OTP 10 HOLD 11 Figure Hold Condition Operation Table COMMAND 12 COMMAND 13 1 Write Enable 13 2 Write Disable 13 3 Read Status Register 14 4 Write Status Register 15 Table Protection 15 5 Read Data Bytes 16 6 Read Data Bytes at Higher Speed 16 7 Dual Output Mode 16 8 Sector Erase 16 9 Block Erase 17 10 Chip Erase 17 11 Page Program 17 12 Deep Power-down 18 13 Release from Deep Power-down RDP , Read Electronic Signature RES 18 14 Read Identification 19 15 Read Electronic Manufacturer ID & Device ID 19 Table ID 19 16 Enter Secured OTP 19 17 Exit Secured OTP 19 18 Read Security Register 20 Table SECURITY REGISTER 20 19 Write Security Register 20 Read SFDP Mode 21 Read Serial Flash Discoverable Parameter RDSFDP 21 Table a. Signature and Parameter Identification Data Values 22 Table b. Parameter Table 0 JEDEC Flash Parameter 23 Table c. Parameter Table 1 Macronix Flash Parameter 25

P/N PM1646

MX25V8006E

POWER-ON 27 ELECTRICAL 28
P/N PM1646

MX25V8006E
8M-BIT [x 1/x 2] CMOS SERIAL FLASH

GENERAL
• Serial Peripheral Interface compatible -- Mode 0 and Mode 3
• 8,388,608 x 1 bit structure or 4,194,304 x 2 bits Dual Output mode structure
• 256 Equal Sectors with 4K byte each
- Any Sector can be erased individually
• 16 Equal Blocks with 64K byte each
- Any Block can be erased individually
• Program Capability
- Byte base - Page base 256bytes
• Single Power Supply Operation - to volt for read, erase, and program operations
• Latch-up protected to 100mA from -1V to Vcc +1V

PERFORMANCE
• High Performance
- Fast access time 75MHz serial clock - Serial clock of Dual Output mode 70MHz - Fast program time 1.4ms typ. and 5ms max. /page 256-byte per page - Byte program time 9us - Fast erase time 60ms typ. /sector 4K-byte per sector 0.7s typ. /block 64K-byte per block
• Low Power Consumption - Low active read current 12mA max. at 75MHz and 4mA max. at 33MHz - Low active programming current 20mA max. - Low active erase current 20mA max. - Low standby current 25uA max. - Deep power-down mode 5uA typ.
• Minimum 100,000 erase/program cycles
• 20 years data retention

SOFTWARE FEATURES
• Input Data Format
- 1-byte Command code
• Advanced Security Features
- Block lock protection The BP2-BP0 status bit defines the size of the area to be software protection against program and erase instructions - Additional 512 bit secured OTP for unique identifier
• Auto Erase and Auto Program Algorithm
- Automatically erases and verifies data at selected sector - Automatically programs and verifies data at selected page by an internal algorithm that automatically times the
program pulse widths Any page to be programed should have page in the erased state first
• Status Register Feature
• Electronic Identification
- JEDEC 1-byte manufacturer ID and 2-byte device ID
- RES command for 1-byte Device ID - REMS command for 1-byte manufacturer ID and 1-byte device ID
• Support Serial Flash Discoverable Parameters SFDP mode

HARDWARE FEATURES
• PACKAGE
- 8-pin SOP 150mil
- 8-land WSON 6x5mm, 0.8mm package height - All devices are RoHS Compliant

P/N PM1646

MX25V8006E

The device features a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus. The four bus signals are a clock input SCLK , a serial data input SI , a serial data output SO , and a chip select CS# . Serial access to the device is enabled by CS# input.

When it is in Dual Output read mode, the SI and SO pins become SIO0 and SIO1 pins for data output.

The device provides sequential read operation on whole chip.

After program/erase command is issued, auto program/erase algorithms which program/erase and verify the specified page or sector/block locations will be executed. Program command is executed on byte basis, or page basis, or word basis for erase command is executes on sector, or block, or whole chip basis.

To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read command can be issued to detect completion status of a program or erase operation via WIP bit.

When the device is not in operation and CS# is high, it is put in standby mode.

The device utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after 100,000 program and erase cycles.

PIN CONFIGURATIONS 8-PIN SOP 150mil

CS# 1 SO/SIO1 2

WP# 3 GND 4
8 VCC 7 HOLD# 6 SCLK 5 SI/SIO0
8-LAND, WSON 6x5mm

CS# 1 SO/SIO1 2

WP# 3 GND 4
8 VCC 7 HOLD# 6 SCLK 5 SI/SIO0

PIN DESCRIPTION

SYMBOL DESCRIPTION

CS# Chip Select

SI/SIO0

Serial Data Input for 1 x I/O / Serial Data Input & Output for Dual Output mode
ORDERING INFORMATION

PART NO. MX25V8006EM1I-13G MX25V8006EZNI-13G

CLOCK MHz

OPERATING CURRENT mA

STANDBY CURRENT uA

Temperature

Package
-40~85°C
8-SOP 150mil
-40~85°C
8-land WSON 6x5mm

Remark

P/N PM1646

MX25V8006E

PART NAME DESCRIPTION MX 25 V 8006E M1 I

OPTION G RoHS Compliant

SPEED 13 75MHz

TEMPERATURE RANGE I Industrial -40°C to 85°C

PACKAGE ZN WSON 0.8mm package height M1 150mil 8-SOP

DENSITY & MODE 8006E 8Mb

TYPE V 2.5V

DEVICE 25 Serial Flash

P/N PM1646

PACKAGE INFORMATION

MX25V8006E

P/N PM1646

MX25V8006E

P/N PM1646

MX25V8006E

Updated VWI value.

Removed Advanced Information.

Modified Figure Write Security Register WRSCUR Sequence

Added Read SFDP RDSFDP Mode

Page P26

Date 2010/12/15

P28,40 JAN/24/2011 P38 P4,8,12, FEB/10/2012 P21~26,31

P/N PM1646

MX25V8006E

Except for customized products which has been expressly identified in the applicable agreement, Macronix's products are designed, developed, and/or manufactured for ordinary business, industrial, personal, and/or household applications only, and not for use in any applications which may, directly or indirectly, cause death, personal injury, or severe property damages. In the event Macronix products are used in contradicted to their target usage above, the buyer shall take any and all actions to ensure said Macronix's product qualified for its actual use in accordance with the applicable laws and regulations and Macronix as well as it’s suppliers and/or distributors shall be released from any and all liability arisen therefrom. Copyright Macronix International Co., Ltd. All rights reserved, including the trademarks and tradename thereof, such as Macronix, MXIC, MXIC Logo, MX Logo, Integrated Solutions Provider, NBit, Nbit, NBiit, Macronix NBit, eLiteFlash, XtraROM, Phines, KH Logo, BE-SONOS, KSMC, Kingtech, MXSMIO, Macronix vEE, Macronix MAP, Rich Audio, Rich Book, Rich TV, and FitCAM. The names and brands of other companies are for identification purposes only and may be claimed as the property of the respective companies. For the contact and order information, please visit Macronix’s Web site at:

MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice. 52

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MX25V8006EZNI-13G Datasheet file may be downloaded here without warranties.

Datasheet ID: MX25V8006EZNI-13G 646955