ICS511MT

ICS511MT Datasheet

ICS511

Part	Datasheet
ICS511MT	ICS511MT (pdf)

Related Parts	Information
ICS511M	ICS511M
ICS511MI	ICS511MI
ICS511MIT	ICS511MIT

PDF Datasheet Preview
LOCO PLL CLOCK MULTIPLIER DATASHEET ICS511 The ICS511 LOCOTM is the most cost effective way to generate a high quality, high frequency clock output from a lower frequency crystal or clock input. The name LOCO stands for Low Cost Oscillator, as it is designed to replace crystal oscillators in most electronic systems. Using Phase-Locked Loop PLL techniques, the device uses a standard fundamental mode, inexpensive crystal to produce output clocks up to 200 MHz. Stored in the chip’s ROM is the ability to generate nine different multiplication factors, allowing one chip to output many common frequencies see table on page The device also has an output enable pin which tri-states the clock output when the OE pin is taken low. This product is intended for clock generation. It has low output jitter variation in the output period , but input to output skew and jitter are not defined nor guaranteed. For applications which require defined input to output skew, use the ICS570B. • Packaged as 8-pin SOIC or die • Available in Pb lead free package • Upgrade of popular ICS501 with: - changed multiplier table - faster operating frequencies - output duty cycle at VDD/2 • Zero ppm multiplication error • Input crystal frequency of 5 - 27 MHz • Input clock frequency of 2 - 50 MHz • Output clock frequencies up to 200 MHz • Extremely low jitter of 25 ps one sigma • Compatible with all popular CPUs • Duty cycle of 45/55 up to 200 MHz • Mask option for nine selectable frequencies • Operating voltage of V or 5 V • Tri-state output for board level testing • Industrial temperature version available • Advanced, low power CMOS process NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 Block Diagram S1:0 2 Crystal or Clock input X1/ICLK X2 Crystal O s c illa to r Optional crystal capacitors PLL Clock M u ltip lie r Circuitry and ROM IDT / ICS LOCO PLL CLOCK MULTIPLIER ICS511 ICS511 LOCO PLL CLOCK MULTIPLIER CLOCK MULTIPLIER Pin Assignment X1/ICLK 1 VDD 2 GND 3 S1 4 8 X2 7 OE 6 S0 5 CLK 8 Pi n 150 mi l SOI C Clock Output Table S1 S0 CLK 4X input 5.333X input 5X input 2.5X input 2X input 3.333X input 6X input 3X input 8X input 0 = connect directly to ground 1 = connect directly to VDD M = leave unconnected floating Common Output Frequency Examples MHz Output 32 40 Input 16 15 Selection S1, S0 M, M, M 1, M, M, M, 0, 0, 0 60 64 10 16 M, 0 1, 0, 0 Ordering Information Part / Order Number 511M* 511MT* 511MI* 511MIT* 511MLF 511MLFT 511MILF 511MILFT 511-DWF 511-DPK Marking ICS511M ICS511I 511MLF 511MILF Shipping Packaging Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Die on uncut, probed wafers Tested die in waffle pack Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC Temperature 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C 0 to +70° C 0 to +70° C *NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 “LF” designates Pb lead free packaging. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT / ICS LOCO PLL CLOCK MULTIPLIER ICS511 ICS511 LOCO PLL CLOCK MULTIPLIER CLOCK MULTIPLIER Innovate with IDT and accelerate your future networks. Contact: For Sales 800-345-7015 408-284-8200 Fax 408-284-2775 For Tech Support Corporate Headquarters Integrated Device Technology, Inc. 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA ICS511 LOCO PLL CLOCK MULTIPLIER CLOCK MULTIPLIER IDT / ICS LOCO PLL CLOCK MULTIPLIER ICS511

PDF Datasheet Preview

LOCO PLL CLOCK MULTIPLIER

DATASHEET

ICS511

The ICS511 LOCOTM is the most cost effective way to generate a high quality, high frequency clock output from a lower frequency crystal or clock input. The name LOCO stands for Low Cost Oscillator, as it is designed to replace crystal oscillators in most electronic systems. Using Phase-Locked Loop PLL techniques, the device uses a standard fundamental mode, inexpensive crystal to produce output clocks up to 200 MHz.

Stored in the chip’s ROM is the ability to generate nine different multiplication factors, allowing one chip to output many common frequencies see table on page

The device also has an output enable pin which tri-states the clock output when the OE pin is taken low.

This product is intended for clock generation. It has low output jitter variation in the output period , but input to output skew and jitter are not defined nor guaranteed. For applications which require defined input to output skew, use the ICS570B.
• Packaged as 8-pin SOIC or die
• Available in Pb lead free package
• Upgrade of popular ICS501 with:
- changed multiplier table
- faster operating frequencies
- output duty cycle at VDD/2
• Zero ppm multiplication error
• Input crystal frequency of 5 - 27 MHz
• Input clock frequency of 2 - 50 MHz
• Output clock frequencies up to 200 MHz
• Extremely low jitter of 25 ps one sigma
• Compatible with all popular CPUs
• Duty cycle of 45/55 up to 200 MHz
• Mask option for nine selectable frequencies
• Operating voltage of V or 5 V
• Tri-state output for board level testing
• Industrial temperature version available
• Advanced, low power CMOS process

NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01

Block Diagram

S1:0 2

Crystal or Clock input

X1/ICLK X2

Crystal O s c illa to r

Optional crystal capacitors

PLL Clock M u ltip lie r Circuitry and ROM

IDT / ICS LOCO PLL CLOCK MULTIPLIER

ICS511

ICS511 LOCO PLL CLOCK MULTIPLIER

CLOCK MULTIPLIER

Pin Assignment

X1/ICLK 1 VDD 2 GND 3 S1 4
8 X2 7 OE 6 S0 5 CLK
8 Pi n 150 mi l SOI C

Clock Output Table

S1 S0

CLK 4X input 5.333X input 5X input 2.5X input 2X input 3.333X input 6X input 3X input 8X input
0 = connect directly to ground 1 = connect directly to VDD M = leave unconnected floating

Common Output Frequency Examples MHz

Output
32 40

Input
16 15

Selection S1, S0 M, M, M 1, M, M, M, 0, 0, 0
60 64
10 16

M, 0 1, 0, 0
Ordering Information

Part / Order Number
511M* 511MT* 511MI* 511MIT* 511MLF 511MLFT 511MILF 511MILFT 511-DWF 511-DPK

Marking

ICS511M ICS511I 511MLF 511MILF

Shipping Packaging

Tubes Tape and Reel

Tubes Tape and Reel

Tubes Tape and Reel

Tubes Tape and Reel Die on uncut, probed wafers Tested die in waffle pack

Package
8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC

Temperature
0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C 0 to +70° C 0 to +70° C
*NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01
“LF” designates Pb lead free packaging.

While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.

IDT / ICS LOCO PLL CLOCK MULTIPLIER

ICS511

ICS511 LOCO PLL CLOCK MULTIPLIER

CLOCK MULTIPLIER

Innovate with IDT and accelerate your future networks. Contact:

For Sales
800-345-7015 408-284-8200 Fax 408-284-2775

For Tech Support

Corporate Headquarters

Integrated Device Technology, Inc.
2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA

ICS511 LOCO PLL CLOCK MULTIPLIER

CLOCK MULTIPLIER

IDT / ICS LOCO PLL CLOCK MULTIPLIER

ICS511

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ICS511MT Datasheet file may be downloaded here without warranties.

Datasheet ID: ICS511MT 636991