ISL97516IUZ-EVALZ

ISL97516IUZ-EVALZ Datasheet


ISL97516 Evaluation Board Application Manual

Part Datasheet
ISL97516IUZ-EVALZ ISL97516IUZ-EVALZ ISL97516IUZ-EVALZ (pdf)
PDF Datasheet Preview
ISL97516 Evaluation Board Application Manual

Application Note

March, 2008

ANXXXX

The ISL97516 EVB is an evaluation kit for evaluating the ISL97516, a step-up voltage regulator that operates with high frequency and high efficiency. This evaluation kit is designed to deliever over 90% efficiency.

The ISL97516 EVB kit provides a dip switch that allows users to select either 620kHz or 1.2MHz switching frequency.

Pinout

ISL97516 10L µTDFN

TOP VIEW

Comp 1 FB 2 EN 3

GND 4
8 SS 7 FSEL 6 VDD 5 LX
• A Complete Evaluation Platform for the ISL97516 evaluation
• Input Voltage 2.3V to 5.5V
• Proven EVB Layout
• RoSH compliant

What is Needed

The following instruments will be needed to perform testing
• Power supplies
• DC Electronic load
• Multimeters
• Oscilloscope
• Cables and wires
Ordering Information

PART # ISL97516IRTZEVAL

DESCRIPTION Evaluation Board for ISL97516

CAUTION These devices are sensitive to electrostatic discharge follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-352-6832 | Intersil and design is a registered trademark of Intersil Americas Inc.

Copyright Intersil Americas Inc. All Rights Reserved

All other trademarks mentioned are the property of their respective owners.

Application Note XXXX

Quick Setup Guide

Step 1 Step 2 Step 3 Step 4 Step 5:

Connect power supply between headers of VIN and GND. The positive output of the power supply should be connected to VIN header. Set power supply voltage between 2.3V and 5V, and current limit at 3A.

Connect E-load between headers of VOUT and GND. The positive input of the E-load should be connected to VOUT header. Set E-load current. The load current should not exceed the maximum output current the part can supply.

Close pin 1 and pin 4 of S1 to tie FSEL pin to VIN to set 1.2MHz switching frequency. Open pin 1 and pin 4 to pull FSEL to ground with R4 to set 620kHz.

Close pin 2 and pin 3 of S1 to tie EN pin to VIN to enable the part. Open pin 2 and pin 3 to pull EN to ground with R3 to disable the part.

Make sure all the connections on the EVB are correct, then turn on power supply and E-load. The part starts to operate.

TABLE Typical Maximumu IOUT Values

VIN V

VOUT V 5

IOMAX mA 870
1150

Table 1 shows typical maximum IOUT values for 1.2MHz switching frequency and 10uH inductor

Maximum Output Current

The MOSFET current limit is norminally 2.0A and guaranteed 1.7A. This restricts the maximum output current that the ISL97516 can drive. Table shows the ISL97516 maximum output current, IOMAX in different input and output voltages.

ANXXXX

March, 2008

Board Design

Schematic

Application Note XXXX
4700pF C6
10k R2
1K R3

R1 85.2k

VOUT 12V 1

CON1

GNDIN 1

CON1

ISL97516

COMP

FSEL 7
/SHDN

VDD 6
More datasheets: MK9173-15CS08LFT | MK9173-15CS08LF | MK9173-15CS08 | MK9173-01CS08T | MK9173-01CS08 | MK9173-15CS08T | ICS853017AM | CC5056F | DEME9SFA197 | SIL05-1A72-71D


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ISL97516IUZ-EVALZ Datasheet file may be downloaded here without warranties.

Datasheet ID: ISL97516IUZ-EVALZ 639214