278-25-336SA2I8

278-25-336SA2I8 Datasheet

278-25-336

Part	Datasheet
278-25-336SA2I8	278-25-336SA2I8 (pdf)

Related Parts	Information
278-25-336SA2I	278-25-336SA2I

PDF Datasheet Preview
Resistance Weld SMD Crystal 278-25-336 For use with IDT’s VCXO-based Synchronization PLLs DATASHEET Specifications Parameters Frequency Resonance Mode Frequency Tolerance 25°C Frequency Stability, ref 25°C Over Operating Temperature Range Temperature Range Operating TOPR Temperature Range, Storage TSTG Equivalent Series Resistance ESR Shunt Capacitance CO Pullability C0 / C1 Load Capacitance CL Drive Level Aging per year Maximum Soldering Temp / Time Moisture Sensitivity Level MSL Termination Finish - 3% - Weight TYP Ratings/Units MHz Fundamental ±20 PPM ±20 PPM -40°C ~ +85°C -40°C ~ +85°C 40 Ohms pF 270 10 pF mW ±3 PPM 260°C / 10 Seconds 1 Sn - Ag - Cu 649 mg Note Dimensional drawing is for reference to critical specifications defined by size measurements. Certain non-critical visual attributes, such as side castellations, etc. may vary. The above specifications, having been carefully prepared and checked, is believed to be accurate at the time of publication however, no responsibility is assumed by IDT for inaccuracies. All specifications subject to change without notice. Package Outline and Dimensions SA2 2015 Integrated Device Technology, Inc. Ordering Information Part / Order Number 278-25-336SA2I 278-25-336SA2I8 Shipping Packaging Cut-Tape Tape and Reel Package x mm SA2 x mm SA2 Temperature -40° to +85° -40° to +85° Corporate Headquarters 6024 Silver Creek Valley Road San Jose, CA 95138 USA Sales 1-800-345-7015 or 408-284-8200 Fax 408-284-2775 Tech Support email: DISCLAIMER Integrated Device Technology, Inc. IDT and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties. IDT’s products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT. Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Product specification subject to change without notice. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third party owners. Copyright 2015 Integrated Device Technology, Inc.. All rights reserved.

PDF Datasheet Preview

Resistance Weld SMD Crystal
278-25-336

For use with IDT’s VCXO-based Synchronization PLLs

DATASHEET

Specifications

Parameters Frequency Resonance Mode Frequency Tolerance 25°C Frequency Stability, ref 25°C Over Operating Temperature Range Temperature Range Operating TOPR Temperature Range, Storage TSTG Equivalent Series Resistance ESR Shunt Capacitance CO Pullability C0 / C1 Load Capacitance CL Drive Level Aging per year Maximum Soldering Temp / Time Moisture Sensitivity Level MSL Termination Finish - 3% - Weight TYP

Ratings/Units MHz Fundamental ±20 PPM ±20 PPM
-40°C ~ +85°C -40°C ~ +85°C
40 Ohms pF 270 10 pF mW ±3 PPM
260°C / 10 Seconds 1

Sn - Ag - Cu 649 mg

Note Dimensional drawing is for reference to critical specifications defined by size measurements. Certain non-critical visual attributes, such as side castellations, etc. may vary. The above specifications, having been carefully prepared and checked, is believed to be accurate at the time of publication however, no responsibility is assumed by IDT for inaccuracies. All specifications subject to change without notice.

Package Outline and Dimensions SA2
2015 Integrated Device Technology, Inc.
Ordering Information

Part / Order Number 278-25-336SA2I 278-25-336SA2I8

Shipping Packaging Cut-Tape

Tape and Reel

Package x mm SA2 x mm SA2

Temperature -40° to +85° -40° to +85°

Corporate Headquarters 6024 Silver Creek Valley Road San Jose, CA 95138 USA

Sales 1-800-345-7015 or 408-284-8200 Fax 408-284-2775

Tech Support email:

DISCLAIMER Integrated Device Technology, Inc. IDT and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties.

IDT’s products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT.

Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Product specification subject to change without notice. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third party owners.

Copyright 2015 Integrated Device Technology, Inc.. All rights reserved.

More datasheets: IPP26CNE8N G | IPD25CNE8N G | MAXGTPREFDES# | 031-8520-006 | 366330023 | 960006AFLFT | JW150C1 | JW050C1 | SLS200PS2X0-01 | 278-25-336SA2I

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 278-25-336SA2I8 Datasheet file may be downloaded here without warranties.

Datasheet ID: 278-25-336SA2I8 636595