PROFIBUS / UART Expansion Interface Description 80-000268RI-2 Assemblies The on-board dedicated UART port provides standard serial interface at data rates up to 115,200 baud. The serial interface is routed to the UART2 serial port of MityARM / MityDSP. This expansion port can accept either the PROFIBUS/RS485 Expansion Board Included in the PROFIBUS Development Kit or an optional RS232 Expansion Board from Critical Link.
Part | Datasheet |
---|---|
![]() |
80-000454 (pdf) |
Related Parts | Information |
---|---|
![]() |
80-000365 |
![]() |
80-000382 |
![]() |
80-000413 |
![]() |
80-000334 |
![]() |
80-000395 |
PDF Datasheet Preview |
---|
Critical Link, LLC PROFIBUS Dev Kit 27 September 2012 • PROFIBUS Interface o Certified by PI International o Real-Time Linux Drivers o Electrically Isolated Interface o Up to 6Mbaud operation • PROFIBUS Support using o MityARM-1810 and 1810F o MityDSP-L138 and L138F • RS485 Support Only using o MityARM-1808 and 1808F • Software Included • Real-Time Linux Kernel • uBoot • User Boot Loader • PROFIBUS PRU Image binary • Slave PROFIBUS Stack evaluation version Digital Interfaces • RS-232 Serial Interface • USB Host Interface • USB OTG Interface • 10/100 MBit Ethernet Interface • Electrically Isolated CAN Bus Interface • UART Expansion for PROFIBUS/RS-485 Interface • DVI Video Interface • SD/MMC Card Socket • Audio Output APPLICATIONS • MityARM1808/1810 and MityDSPL138 Evaluation • PROFIBUS Development • Process Automation • Factory Automation • Industrial Automation • Embedded Instrumentation • Rapid Prototyping Expansion • 3 50-pin IO Expansion Slots • Integrated +3V/+5V/±12V Power Supply DESCRIPTION The PROFIBUS DEVELOPMENT KIT provides all the hardware and software support for system designers and developers to evaluate the AM1810 or OMAPL138 Microprocessors for PROFIBUS as well as the Critical Link MityARM-1810 and/or MityDSP-L138 series System on Modules. Included is a MityARM-1810 module, but the kit is fully compatible with MityARM-1810, MityDSP-L138, and MityARM-1808 modules with varying PROFBIUS support. See the compatibility chart below. Module Type MityARM-1810 MityARM-1810F MityDSP-L138 MityDSP-L138F MityARM-1808 MityARM-1808F PROFIBUS Support Yes No RS485 Support Yes Copyright 2007-2012, Critical Link LLC Critical Link, LLC PROFIBUS Dev Kit 27 September 2012 In addition, the PROFIBUS DEVELOPMENT KIT includes on board RS-232, 10/100 MBit Ethernet, Universal Serial Bus USB Host and USB-On The-Go OTG communication interfaces and an Electrically Isolated CAN interface. The single UART expansion port allows for the connection of either the PROFIBUS/RS-485 expansion board included with the PROFIBUS Development Kit with 2500V galvanic isolation barrier or a simple RS232 serial port expansion kit optional . Integrated Digital Video Interface DVI controller for external display connection with DDC support. Interface to display via 5 pair LVDS link with additional SPI interface for resistive touch controller requires an FPGA based module to be installed , Multi Media Card MMC interface, 3 I/O Expansion connectors for custom add-on card and integrated power supply with +3V/+5V/±12V outputs from single 12VDC input. A block diagram of the PROFIBUS DEVELOPMENT KIT is illustrated in Figure All available processor GPIO ports and FPGA I/O lines if FPGA module is installed are either used directly by the PROFIBUS DEVELOPMENT KIT or are routed to the 3 50pin Expansion IO connectors. Control of the on-board interface hardware and connected Expansion IO cards require proper configuration of the MityARM / MityDSP ARM, DSP, and FPGA. While not required, it is strongly recommended that the MityARM software and firmware development kit and supplied API be used to manage these interfaces. HID / Thumb drive SD Card Disk Serial Ethernet Profinet Modbus TCP EtherCAT Master Audio Line Out RS232/ RS485/ Profibus Monitor Panel w/Touch or GPIO +12V USB-A Connector Micro-USB Connector Micro-SD Connector SATA Header 10-pin Header RJ-45 & Magnetics 10-pin Hdr 1/8" stereo jack 10-pin Hdr DVI LCD / Touch Header ISO 1050 Filter MityARM-1810 PROFIBUS Development Kit USB1 USB0 MMCSD 0 ORDERING INFORMATION Development Kits The following table lists the orderable module configurations. For shipping status, availability, and lead time of these or other configurations please contact your Critical Link representative. Table 13 Orderable Model Numbers Development Kit Model Module Included PROFIBUS Support 80-000365 L138-FI-225-RC 80-000382 L138-FI-236-RL 80-000395 L138-FG-225-RC 80-000413 L138-DG-225-RI 80-000454 L138-DI-225-RI 80-000334 L138-FX-225-RC 80-000315 1808-FG-225-RC 80-000317 1808-FX-225-RC 80-000320 1810-DG-225-RC 80-000348 1810-DX-225-RC LVDS/LCD Support Yes No Yes No Yes No Expansions Kits The following table lists the orderable expansion kits for the above development kits. For shipping status, availability, and lead time of these or other configurations please contact your Critical Link representative. Expansion Kit Model 80-000358 80-000450 80-000289 Table 14 Orderable Expansion Kit Numbers Type Interface Port Notes RS232 Expansion Board J504 PROFIBUS RS485 Expansion J504 Board included WQVGA LCD w/Driver |
More datasheets: CY62147DV30LL-70BVXAT | CY62147DV30LL-70BVXA | CY62147DV30L-55BVXET | WLNG-AN-DP101-G | WLNG-SE-DP101-G | B10-03B | B10-05B | TIPL762A-S | TIPL762-S | 80-000365 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 80-000454 Datasheet file may be downloaded here without warranties.