Part | Datasheet |
---|---|
![]() |
BF140D03BK1200 (pdf) |
Related Parts | Information |
---|---|
![]() |
BF140A01RE0000 |
![]() |
BF240SD3GR2500 |
PDF Datasheet Preview |
---|
42,00 21,00 35,50 17,75 APEM BF Series Paddle Control 7,20 R 2,50 2,90 1,45 O 38,00 O 4,16 2,10 1,05 0,80 x45°CHAMFER 0,75 HALL EFFECT JOYSTICK AND SWITCH FUNCTIONS O 3,00 O 1,60 11,75 99,5 2,28 0,46 5,71 SCULPTED ERGONOMIC DESIGN 5V OPERATION - DUAL REDUND2,5A0 NT OUTPUTS AS STANDARD EMC & MAGNETICALLY SHIELDED - ANALOGUE OR PWM OUTPUTS 45° NEXT GENERATION HALL EFFECT TECHNOLOGY O 2,50 4,80 45° AVAILABLE WITH COLOUR-CODED INSERTS SPRUNG AND DETENT LEVER OPTIONS IP67 SEALED M2ThrededHole BF SERIES PADDLE - CONTACTLESS JOYSTICK & SWITCH PRODUCT OVERVIEW The BF Series Paddle is the very latest generation in high precision contactless controls. It combines the features of a contactless single axis joystick and a switch in one control. Long trouble-free life is assured with the latest hall effect technology, providing a range of analogue, switched or custom PWM output options. The all-new design with its innovative mechanism and ergonomic styling is specifically designed for robustness, strength and performance. As well as all of the features you would expect from the very latest in joystick technology, the innovative design of the BF Series Paddle introduces a number of new functions and product features: EFFECTIVELY ZERO BELOW PANEL DEPTH ERGONOMIC DESIGN COMBINES CONTACTLESS JOYSTICK AND SWITCH FUNCTIONS IN ONE CONTROL TWO HALL EFFECT SWITCHES WITH SELECTABLE SWITCHING POINTS TWO INDEPENDENT ANALOGUE OUTPUTS WITH A RANGE OF GAIN OPTIONS DUAL REDUNDANT OUTPUTS AS STANDARD - With either the same or inverted polarity. PWM OUTPUT OPTIONS END STACKABLE MOUNTING AVAILABLE WITH A RANGE OF COLOURED HANDLE INSERTS INNOVATIVE HARD-WEARING MECHANISM LEVER CAN BE SPRUNG TO CENTRE, WITH OR WITHOUT DETENTS, OR CAN BE FRICTIONED WITH DETENTS DETENT LEVER OPTION PROVIDES TACTILE FEEDBACK AND ALLOWS POSITIVE POSITIONING HIDDEN FIXINGS HALL EFFECT SENSING - Latest technology, a reduced part count and an ease of integration. HIGH EMC IMMUNITY - Integral shielding, as standard. MAGNETICALLY SCREENED INDUSTRY STANDARD CONNECTOR Note The company reserves the right to change specifications without notice. BF SERIES PADDLE - CONTACTLESS JOYSTICK & SWITCH CONFIGURATIONS & OUTPUTS OUTPUT OPTIONS The BF Series Paddle is configured as two “electrical” controls in one mechanical package. The Paddle operates from 5V and provides two proportional outputs. The second output is accurate to the first within +/-2% of the power supply. The power supply for the secondary output is also completely independent. Customers may choose their preference of voltage outputs gains . The secondary output can be of the same or inverse polarity to the primary wiper. For example, with a secondary inverse output, the first and second outputs can be summed and compared to zero to verify that the joystick is operating correctly. Paddles having two identical outputs of the same polarity may be used to drive two identical dual redundant circuits. There are also two Hall Effect switches that trigger at pre-determined lever positions. The BF Series Paddle may be specified with a variety of PWM output options. For more details on available PWM options please refer to Apem. The Paddle incorporates two Hall Effect switches. The angle of the lever at the switch trigger point can be selected when ordering. If no switches are specified then the output on pins 2 and 7 will be unused. The outputs are configured as ‘open drain’ type with a 1K5 pull up resistor to 5V. GAIN OPTIONS The voltage output on the wiper, at full scale deflection is determined by the gain. The gain is expressed as a percentage of the voltage supplied. Therefore assuming a 5V supply a Paddle specified with +/- 25% gain would yield 1.25V at South, 2.5V at centre and 3.75V at North. A range of gain options are available as standard. All controls are supplied pre-set and no further calibration is needed throughout the lifetime of operation. OUTPUT IMPEDANCE The voltage outputs at centre and at each end of travel are specified across an infinite load, with no current flowing. The output impedance specified in the electrical specification should be taken into account when designing a system. Load resistance of less than 10K Ohms is not recommended. Note The company reserves the right to change specifications without notice. BF SERIES PADDLE - CONTACTLESS JOYSTICK & SWITCH MECHANICAL & CONNECTION INFORMATION MECHANISM The brand new mechanism design has been developed for strength and long life whilst retaining a superb feel. SPRUNG TO CENTRE The lever springs back to the centre position when released. DETENT POSITIONS The lever ‘clicks’ into a number of preset positions. The internal switches can be configured to trigger at 2 of these points. DETENT POSITIONS WITH SPRUNG TO CENTRE The lever ‘clicks’ into a number of preset positions and springs back to its centre position when released. CONNECTIONS The Paddle is fitted, as standard, with an industry standard 2.54mm pitch 8 way connector. CONNECTIONS Paddles are supplied with an eight way connector as standard. PIN 1 5V PIN 2 Switch 1 + PIN 3 0V PIN 4 Analogue / PWM output 1 PIN 5 Analogue / PWM ouptut 2 PIN 6 0V PIN 7 Switch 2 - PIN 8 5V BF SERIES OUTPUT CHARACTERISTICS 40% GAIN DUAL INVERSE OUTPUTS Switches at Degrees 4.5V 4 Output 1 Switches at 25 Degrees 4.5V 4 PIN 1 Output 1 Switch 2 On Switch 1 On Switch 2 Switch 1 -25 -20 20 25 Output 2 Degrees Deflection -25 -20 Output 2 Degrees Deflection 20 25 |
More datasheets: 1308 | MV9101 | SP1486EMN-L/TR | SP1486EMN-L | HLMP-Y801-JPP00 | 1700 | 74F322PC | 3294-15SUGC/S400-A5 | BF140A01RE0000 | BF240SD3GR2500 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived BF140D03BK1200 Datasheet file may be downloaded here without warranties.