USB-SMBUS-CABLEZ

USB-SMBUS-CABLEZ Datasheet

USB-to-I2C Interface Dongles USB-SMBUS-CABLEZ, USB-5PSMBUS-CABLEZ

Part	Datasheet
USB-SMBUS-CABLEZ	USB-SMBUS-CABLEZ (pdf)

Related Parts	Information
USB-5PSMBUS-CABLEZ	USB-5PSMBUS-CABLEZ

PDF Datasheet Preview
USB-to-I2C Interface Dongles USB-SMBUS-CABLEZ, USB-5PSMBUS-CABLEZ This data sheet provides details of the interface dongles. The USB-SMBUS-CABLEZ is a 3-pin version designed for use with the ADM1062/ADM1063/ADM1064/ADM1065/ ADM1066/ADM1067/ADM1068/ADM1069 hereafter referred to as ADM1062 to ADM1069 family of programmable super sequencers. The USB-5PSMBUS-CABLEZ is a 5-pin version for use with the ADM1175/ADM1176/ADM1177/ADM1178 family of hot swap controllers and ADM1191x power monitoring devices. The dongles are designed to connect a standard PC or notebook USB port to a 3-pin or 5-pin header on an evaluation board, system board, or preprogramming module. The dongles can then be used to access and program a supported I2C device using the appropriate PC software. Note that a suitable power supply must also be provided to the device. Both dongles provide clock SCL , data SDA , and GND signals. The USB-5PSMBUS-CABLEZ also provides a CONV and an ALERT signal. The signals are labeled on the crimp housing of the cable. It is advisable to mark Pin 1 of the header on the board to ensure correct orientation upon connection, as shown in Figure 2 shows the schematic for the PCB contained in the USB port dongle. The schematic is the same for the USB-SMBUS-CABLEZ and the USB-5PSMBUS-CABLEZ. SCL SDA GND 3-PIN HEADER ON ADM1062 TO ADM1069 EVALUATION BOARD SCL SDA GND 3-TERMINAL CRIMP HOUSING CABLE USB-SMBUS-CABLEZ USB-TO-I2C DONGLE SCL SDA GND CONV ALERT PIN 1 SCL SDA GND CONV ALERT CABLE 5-PIN HEADER ON ADM1175/ADM1176/ADM1177/ ADM1178 OR ADM119x EVALUATION BOARD 5-TERMINAL CRIMP HOUSING USB-5PSMBUS-CABLEZ USB-TO-I2C DONGLE PIN 1 IS INDICATED BY A TRIANGLE ON THE CRIMP HOUSING. Figure USB-to-I2C Dongle Cable Connections TO PC USB PORT TO PC USB PORT 07624-001 Evaluation boards are only intended for device evaluation and not for production purposes. Evaluation boards are supplied “as is” and without warranties of any kind, express, implied, or statutory including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. No license is granted by implication or otherwise under any patents or other intellectual property by application or use of evaluation boards. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Analog Devices reserves the right to change devices or specifications at any time without notice. Trademarks and registered trademarks are the property of their respective owners. Evaluation boards are not authorized to be used in life support devices or systems. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: Fax: 2008 Analog Devices, Inc. All rights reserved. USB-SMBUS-CABLEZ, USB-5PSMBUS-CABLEZ EVALUATION BOARD SOFTWARE DRIVER INSTALLATION Version or later of the ADM1062 to ADM1069 evaluation software or Version of the ADM1175/ADM1176/ADM1177/ ADM1178 and ADM119x evaluation software provides the necessary software support for the USB-to-I2C interface dongle. To install the driver software, perform the following steps: Install the evaluation software before the cable is plugged in. If prompted by the software, restart the PC. Plug the cable into a free USB port on the PC. The operating system recognizes that a new device has been attached and asks if you want to install new drivers for it. Select the default option, which is to let the operating system locate the drivers for you, and click Continue to search for the drivers. Depending on your PC settings, you may also be prompted that the driver you are installing is unsigned. Click Continue Anyway if prompted to complete the driver installation. The cable is now ready for use. Note that on certain PC configurations you will be prompted to install the drivers the first time you plug the cable into each of the USB ports on the PC. Once this installation is complete for a port, it does not need to be repeated. For more information on these devices and to download the evaluation software, visit WARNING ORDERING INFORMATION BILL OF MATERIALS Table Qty Reference Designator C2, C4 to C7, C9, C14, C15, C16 C3, C8 C10, C11 C12, C13 R1 to R3 R4, R9, R10, R12, R13 R6, R7 R11, R14 SLK1 1 FEC = Farnell Electronics. Description 10 nF capacitor, 0603 47 nF capacitor, 0603 uF capacitor, Case R 470 nF capacitor, 0603 12 pF capacitor, 0603 Green LED, 0603 ADP3303-3.3, IC, 8-lead SOIC 24LC64, IC, 8-lead SOIC ADG836, IC, 10-lead MSOP CY7C68013A-56LFXC, IC, 56-lead QFN P82B96, IC, 8-lead SOIC 7-pin, connector, through-hole pads 10 kΩ resistor, 0603 kΩ resistor, 0603 330 kΩ resistor, 0603 100 kΩ resistor, 0603 1 kΩ resistor, 0603 100 Ω resistor, 0805 USB SKT connector, USB Plug Type A SLK 3W, link, solder pads 24 MHz crystal, HC49/4H ORDERING GUIDE Model USB-SMBUS-CABLEZ1 USB-5PSMBUS-CABLEZ1 Description USB Port to 3-Pin I2-Interface Cable USB Port to 5-Pin I2C-Interface Cable 1 Z = RoHS Compliant Part. ESD CAUTION Supplier/Part Number1 FEC 301-9561 FEC 317-445 FEC 197-002 FEC 317-275 FEC 721-979 FEC 114-1096 Analog Devices ADP3303 FEC 975-8070 Analog Devices ADG836 Digi-Key 428-1669-ND FEC 890-6068 Not fitted FEC 923-3504 FEC 933-0810 FEC 933-1042 FEC 933-0402 FEC 933-0380 FEC 923-3881 FEC 130-8875 N/A FEC 950-9640 2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. EB076240-0-8/08 0

PDF Datasheet Preview

USB-to-I2C Interface Dongles USB-SMBUS-CABLEZ, USB-5PSMBUS-CABLEZ

This data sheet provides details of the interface dongles. The USB-SMBUS-CABLEZ is a 3-pin version designed for use with the ADM1062/ADM1063/ADM1064/ADM1065/ ADM1066/ADM1067/ADM1068/ADM1069 hereafter referred to as ADM1062 to ADM1069 family of programmable super sequencers. The USB-5PSMBUS-CABLEZ is a 5-pin version for use with the ADM1175/ADM1176/ADM1177/ADM1178 family of hot swap controllers and ADM1191x power monitoring devices.

The dongles are designed to connect a standard PC or notebook USB port to a 3-pin or 5-pin header on an evaluation board, system board, or preprogramming module. The dongles can
then be used to access and program a supported I2C device using the appropriate PC software. Note that a suitable power supply must also be provided to the device.

Both dongles provide clock SCL , data SDA , and GND signals. The USB-5PSMBUS-CABLEZ also provides a CONV and an ALERT signal. The signals are labeled on the crimp housing of the cable. It is advisable to mark Pin 1 of the header on the board to ensure correct orientation upon connection, as shown in Figure 2 shows the schematic for the PCB contained in the USB port dongle. The schematic is the same for the USB-SMBUS-CABLEZ and the USB-5PSMBUS-CABLEZ.

SCL SDA GND
3-PIN HEADER ON ADM1062 TO ADM1069

EVALUATION BOARD

SCL SDA GND
3-TERMINAL CRIMP HOUSING

CABLE

USB-SMBUS-CABLEZ

USB-TO-I2C DONGLE

SCL SDA GND CONV ALERT

PIN 1 SCL SDA GND CONV ALERT

CABLE
5-PIN HEADER ON ADM1175/ADM1176/ADM1177/

ADM1178 OR ADM119x EVALUATION BOARD
5-TERMINAL CRIMP HOUSING

USB-5PSMBUS-CABLEZ

USB-TO-I2C DONGLE

PIN 1 IS INDICATED BY A TRIANGLE ON THE CRIMP HOUSING.

Figure USB-to-I2C Dongle Cable Connections

TO PC USB PORT

TO PC USB PORT
07624-001

Evaluation boards are only intended for device evaluation and not for production purposes. Evaluation boards are supplied “as is” and without warranties of any kind, express, implied, or statutory including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. No license is granted by implication or otherwise under any patents or other intellectual property by application or use of evaluation boards. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Analog Devices reserves the right to change devices or specifications at any time without notice. Trademarks and registered trademarks are the property of their respective owners. Evaluation boards are not authorized to be used in life support devices or systems.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel:

Fax:
2008 Analog Devices, Inc. All rights reserved.

USB-SMBUS-CABLEZ, USB-5PSMBUS-CABLEZ

EVALUATION BOARD SOFTWARE

DRIVER INSTALLATION

Version or later of the ADM1062 to ADM1069 evaluation software or Version of the ADM1175/ADM1176/ADM1177/ ADM1178 and ADM119x evaluation software provides the necessary software support for the USB-to-I2C interface dongle. To install the driver software, perform the following steps:

Install the evaluation software before the cable is plugged in. If prompted by the software, restart the PC.

Plug the cable into a free USB port on the PC. The operating system recognizes that a new device has been attached and asks if you want to install new drivers for it.

Select the default option, which is to let the operating system locate the drivers for you, and click Continue to search for the drivers. Depending on your PC settings, you may also be prompted that the driver you are installing is unsigned. Click Continue Anyway if prompted to complete the driver installation. The cable is now ready for use.

Note that on certain PC configurations you will be prompted to install the drivers the first time you plug the cable into each of the USB ports on the PC. Once this installation is complete for a port, it does not need to be repeated.

For more information on these devices and to download the evaluation software, visit

WARNING
ORDERING INFORMATION

BILL OF MATERIALS

Table

Qty Reference Designator

C2, C4 to C7, C9, C14, C15, C16

C3, C8

C10, C11

C12, C13

R1 to R3

R4, R9, R10, R12, R13

R6, R7

R11, R14

SLK1
1 FEC = Farnell Electronics.

Description 10 nF capacitor, 0603 47 nF capacitor, 0603 uF capacitor, Case R 470 nF capacitor, 0603 12 pF capacitor, 0603 Green LED, 0603 ADP3303-3.3, IC, 8-lead SOIC 24LC64, IC, 8-lead SOIC ADG836, IC, 10-lead MSOP CY7C68013A-56LFXC, IC, 56-lead QFN P82B96, IC, 8-lead SOIC 7-pin, connector, through-hole pads 10 kΩ resistor, 0603 kΩ resistor, 0603 330 kΩ resistor, 0603 100 kΩ resistor, 0603 1 kΩ resistor, 0603 100 Ω resistor, 0805 USB SKT connector, USB Plug Type A SLK 3W, link, solder pads 24 MHz crystal, HC49/4H
ORDERING GUIDE

Model USB-SMBUS-CABLEZ1 USB-5PSMBUS-CABLEZ1

Description USB Port to 3-Pin I2-Interface Cable USB Port to 5-Pin I2C-Interface Cable
1 Z = RoHS Compliant Part.

ESD CAUTION

Supplier/Part Number1 FEC 301-9561 FEC 317-445 FEC 197-002 FEC 317-275 FEC 721-979 FEC 114-1096 Analog Devices ADP3303 FEC 975-8070 Analog Devices ADG836 Digi-Key 428-1669-ND FEC 890-6068 Not fitted FEC 923-3504 FEC 933-0810 FEC 933-1042 FEC 933-0402 FEC 933-0380 FEC 923-3881 FEC 130-8875 N/A FEC 950-9640
2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.

EB076240-0-8/08 0

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived USB-SMBUS-CABLEZ Datasheet file may be downloaded here without warranties.

Datasheet ID: USB-SMBUS-CABLEZ 517987