TSL13FN

TSL13FN Datasheet

TSL13FN_Datasheet, Rev. Converters

Part	Datasheet
TSL13FN	TSL13FN (pdf)

PDF Datasheet Preview
Effective Document - Printout not Controlled TSL13FN Light-to-Voltage Converters Figure 1 Added Value of Using TSL13FN Approximates Human Eye Response High Irradiance Responsivity to Green Low Supply Current The TSL13FN is a cost optimized, highly integrated light-to-voltage optical sensor that contains a photodiode and a transimpedance amplifier with a 20 MΩ feedback resistor on a single monolithic integrated circuit. The photodiode active area is 0.5mm x 0.5mm and the sensor responds to visible light in the range of 300 nm to 1100 nm. The output voltage is linear with light intensity irradiance incident on the sensor over a wide dynamic range. These devices are supplied in a surface mountable package. Ordering Information and Content Guide appear at end of datasheet. Key Benefits & Features The benefits and features of TSL13FN are listed below: Single Diode mV/ uW/cm2 at λp = 525nm 0.8mA Typical Figure 2 TSL13FN Block Diagram Block Diagram The functional blocks of this device for reference are shown below: ams Datasheet 2014-Jun-04 [1-00] Release Date 2014-06-17, Key Contact Matt Kroese Voltage Output TSL13FN 1 Effective Document - Printout not Controlled Pin Assignment Figure 3 Pin Diagram Top View Pin Assignment VDD 1 OUTPUT 2 NO CONNECT 3 6 GND 5 NO CONNECT 4 NO CONNECT Pin Description Figure 4 Pin Description Pin Number 1 2 3 4 5 6 Pin Name VDD OUT N/C N/C N/C GND Supply voltage Output voltage No connection No connection No connection Power supply ground. All voltages are referenced to GND TSL13FN 2 Release Date 2014-06-17, Key Contact Matt Kroese ams Datasheet 2014-Jun-04 [1-00] Absolute Maximum Ratings Absolute Maximum Ratings Figure 5 Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only. Functional operation of the device at these or any other conditions beyond those indicated under “Operating Conditions” is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameter Supply voltage Output current Tstg Storage temperature range Min Max Units Comments V All voltages are with respect to GND -10 mA -40 85 Effective Document - Printout not Controlled ams Datasheet 2014-Jun-04 [1-00] Release Date 2014-06-17, Key Contact Matt Kroese Ordering & Contact Information Ordering & Contact Information Figure 21 Ordering Information Device TSL13 0 to 70°C Package Description Package Designator Ordering Number 6-lead Surface Mount TSL13FN Buy our products or get free samples online at Technical Support is available at For further information and requests, e-mail us at For sales offices, distributors and representatives, please visit: Headquarters ams AG Tobelbaderstrasse 30 8141 Unterpremstaetten Austria, Europe Tel +43 0 3136 500 0 Website: Effective Document - Printout not Controlled TSL13FN 14 Release Date 2014-06-17, Key Contact Matt Kroese ams Datasheet 2014-Jun-04 [1-00] RoHS Compliant & ams Green Statement RoHS Compliant & ams Green Statement RoHS The term RoHS compliant means that ams AG products fully comply with current RoHS directives. Our semiconductor products do not contain any chemicals for all 6 substance categories, including the requirement that lead not exceed by weight in homogeneous materials. Where designed to be soldered at high temperatures, RoHS compliant products are suitable for use in specified lead-free processes. ams Green RoHS compliant and no Sb/Br ams Green defines that in addition to RoHS compliance, our products are free of Bromine Br and Antimony Sb based flame retardants Br or Sb do not exceed by weight in homogeneous material . Important Information The information provided in this statement represents ams AG knowledge and belief as of the date that it is provided. ams AG bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. ams AG has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. ams AG and ams AG suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Effective Document - Printout not Controlled ams Datasheet 2014-Jun-04 [1-00] Release Date 2014-06-17, Key Contact Matt Kroese TSL13FN 15 Copyrights & Disclaimer Copyrights & Disclaimer Copyright ams AG, Tobelbader Strasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. Devices sold by ams AG are covered by the warranty and patent indemnification provisions appearing in its General Terms of Trade. ams AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein. ams AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with ams AG for current information. This product is intended for use in commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by ams AG for each application. This product is provided by ams AG “AS IS” and any express or implied warranties, including, but not limited to the implied warranties of merchantability and fitness for a particular purpose are disclaimed. ams AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of ams AG rendering of technical or other services. Effective Document - Printout not Controlled TSL13FN 16 Release Date 2014-06-17, Key Contact Matt Kroese ams Datasheet 2014-Jun-04 [1-00] Document Status Document Status Document Status Product Status Definition Product Preview Pre-Development Information in this datasheet is based on product ideas in the planning phase of development. All specifications are design goals without any warranty and are subject to change without notice Preliminary Datasheet Pre-Production Information in this datasheet is based on products in the design, validation or qualification phase of development. The performance and parameters shown in this document are preliminary without any warranty and are subject to change without notice Datasheet Production Information in this datasheet is based on products in ramp-up to full production or full production which conform to specifications in accordance with the terms of ams AG standard warranty as given in the General Terms of Trade Datasheet discontinued Discontinued Information in this datasheet is based on products which conform to specifications in accordance with the terms of ams AG standard warranty as given in the General Terms of Trade, but these products have been superseded and should not be used for new designs Effective Document - Printout not Controlled ams Datasheet 2014-Jun-04 [1-00] Release Date 2014-06-17, Key Contact Matt Kroese TSL13FN 19

PDF Datasheet Preview

Effective Document - Printout not Controlled

TSL13FN

Light-to-Voltage Converters

Figure 1 Added Value of Using TSL13FN

Approximates Human Eye Response High Irradiance Responsivity to Green Low Supply Current
The TSL13FN is a cost optimized, highly integrated light-to-voltage optical sensor that contains a photodiode and a transimpedance amplifier with a 20 MΩ feedback resistor on a single monolithic integrated circuit. The photodiode active area is 0.5mm x 0.5mm and the sensor responds to visible light in the range of 300 nm to 1100 nm. The output voltage is linear with light intensity irradiance incident on the sensor over a wide dynamic range. These devices are supplied in a surface mountable package. Ordering Information and Content Guide appear at end of datasheet.

Key Benefits & Features

The benefits and features of TSL13FN are listed below:

Single Diode mV/ uW/cm2 at λp = 525nm 0.8mA Typical

Figure 2 TSL13FN Block Diagram

Block Diagram

The functional blocks of this device for reference are shown below:
ams Datasheet 2014-Jun-04 [1-00] Release Date 2014-06-17, Key Contact Matt Kroese

Voltage Output

TSL13FN 1

Effective Document - Printout not Controlled

Pin Assignment

Figure 3 Pin Diagram Top View

Pin Assignment

VDD 1 OUTPUT 2 NO CONNECT 3
6 GND 5 NO CONNECT 4 NO CONNECT

Pin Description

Figure 4 Pin Description

Pin Number
1 2 3 4 5 6

Pin Name

VDD OUT N/C N/C N/C GND

Supply voltage Output voltage No connection No connection No connection Power supply ground. All voltages are referenced to GND

TSL13FN 2 Release Date 2014-06-17, Key Contact Matt Kroese
ams Datasheet 2014-Jun-04 [1-00]

Absolute Maximum Ratings

Absolute Maximum Ratings

Figure 5 Absolute Maximum Ratings

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only. Functional operation of the device at these or any other conditions beyond those indicated under “Operating Conditions” is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Parameter

Supply voltage

Output current

Tstg

Storage temperature range

Min Max Units

Comments

V All voltages are with respect to GND
-10 mA
-40 85

Effective Document - Printout not Controlled
ams Datasheet 2014-Jun-04 [1-00] Release Date 2014-06-17, Key Contact Matt Kroese
Ordering & Contact Information
Ordering & Contact Information
Figure 21 Ordering Information

Device

TSL13
0 to 70°C
Package Description Package Designator Ordering Number
6-lead Surface Mount

TSL13FN

Buy our products or get free samples online at Technical Support is available at For further information and requests, e-mail us at For sales offices, distributors and representatives, please visit:

Headquarters ams AG Tobelbaderstrasse 30 8141 Unterpremstaetten Austria, Europe

Tel +43 0 3136 500 0 Website:

Effective Document - Printout not Controlled

TSL13FN 14 Release Date 2014-06-17, Key Contact Matt Kroese
ams Datasheet 2014-Jun-04 [1-00]

RoHS Compliant & ams Green Statement

RoHS Compliant & ams Green Statement

RoHS The term RoHS compliant means that ams AG products fully comply with current RoHS directives. Our semiconductor products do not contain any chemicals for all 6 substance categories, including the requirement that lead not exceed by weight in homogeneous materials. Where designed to be soldered at high temperatures, RoHS compliant products are suitable for use in specified lead-free processes.
ams Green RoHS compliant and no Sb/Br ams Green defines that in addition to RoHS compliance, our products are free of Bromine Br and Antimony Sb based flame retardants Br or Sb do not exceed by weight in homogeneous material .

Important Information The information provided in this statement represents ams AG knowledge and belief as of the date that it is provided. ams AG bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. ams AG has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. ams AG and ams AG suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

Effective Document - Printout not Controlled
ams Datasheet 2014-Jun-04 [1-00] Release Date 2014-06-17, Key Contact Matt Kroese

TSL13FN 15

Copyrights & Disclaimer

Copyrights & Disclaimer

Copyright ams AG, Tobelbader Strasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner.

Devices sold by ams AG are covered by the warranty and patent indemnification provisions appearing in its General Terms of Trade. ams AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein. ams AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with ams AG for current information. This product is intended for use in commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by ams AG for each application. This product is provided by ams AG “AS IS” and any express or implied warranties, including, but not limited to the implied warranties of merchantability and fitness for a particular purpose are disclaimed.
ams AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of ams AG rendering of technical or other services.

Effective Document - Printout not Controlled

TSL13FN 16 Release Date 2014-06-17, Key Contact Matt Kroese
ams Datasheet 2014-Jun-04 [1-00]

Document Status

Document Status

Document Status Product Status

Definition

Product Preview

Pre-Development

Information in this datasheet is based on product ideas in the planning phase of development. All specifications are design goals without any warranty and are subject to change without notice

Preliminary Datasheet

Pre-Production

Information in this datasheet is based on products in the design, validation or qualification phase of development. The performance and parameters shown in this document are preliminary without any warranty and are subject to change without notice

Datasheet

Production

Information in this datasheet is based on products in ramp-up to full production or full production which conform to specifications in accordance with the terms of ams AG standard warranty as given in the General Terms of Trade

Datasheet discontinued

Discontinued

Information in this datasheet is based on products which conform to specifications in accordance with the terms of ams AG standard warranty as given in the General Terms of Trade, but these products have been superseded and should not be used for new designs
Effective Document - Printout not Controlled
ams Datasheet 2014-Jun-04 [1-00] Release Date 2014-06-17, Key Contact Matt Kroese

TSL13FN 19

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived TSL13FN Datasheet file may be downloaded here without warranties.

Datasheet ID: TSL13FN 519819