1483

1483 Datasheet

PRODUCT ID 1483

Part	Datasheet
1483	1483 (pdf)

PDF Datasheet Preview
13.56MHz RFID/NFC Plastic Nail PRODUCT ID 1483 Description • This is a blank 13.56MHz RFID/NFC 'nail'- often used to 'hammer' in a 13.56MHz RFID/NFC tag. The nail contains a small RFID chip and an antenna, and is passively powered by the reader/writer when placed a couple inches away. These can be read by almost any 13.56MHz RFID/NFC reader but make sure it can handle ISO/IEC 14443 Type A cards as there are a few other encoding standards like FeLica They are tested and work great with both our PN532 NFC/RFID breakout board and Adafruit NFC/RFID Shield for Arduino! These chips can be written to & store up to 1 KB of data in writable EEPROM divided into banks, and can handle over 100,000 re-writes. You can use our PN532 NFC/RFID breakout board or Adafruit NFC/RFID Shield for Arduino to read and write data to the EEPROM inside the tag. There is also a permanent 4-byte ID burned into the chip that you can use to identify one tag from another - the ID number cannot be changed. These use a ISO/IEC 14443 Type A chipset, which used to be the 'classic' NFC chipset. In ~2014, the NFC forum decided not to support this chipset anymore, so newer phones do not support it. This only matters if you're trying to use this tag with a phone/tablet. Technical Details • RFID chip specification: o 1 KiloByte 8 KiloBit non-volatile EEPROM storage o Built in encryption engine with 48-bit key o 4 Byte unique identifier burned into the chip o MHz frequency Tag specification o Max Dimensions 22.11mm / round x / long o Head Dimensions 22.11mm / round x 4.06mm / thick o Shaft Dimensions 6mm / round x 38.23mm / long o 2.32g o Works about 2" away from reader Engineered in NYC Adafruit

PDF Datasheet Preview

13.56MHz RFID/NFC Plastic Nail

PRODUCT ID 1483

Description
• This is a blank 13.56MHz RFID/NFC 'nail'- often used to 'hammer' in a 13.56MHz RFID/NFC tag. The nail contains a small RFID chip and an antenna, and is passively powered by the reader/writer when placed a couple inches away. These can be read by almost any 13.56MHz RFID/NFC reader but make sure it can handle ISO/IEC 14443 Type A cards as there are a few other encoding standards like FeLica They are tested and work great with both our PN532 NFC/RFID breakout board and Adafruit NFC/RFID Shield for Arduino! These chips can be written to & store up to 1 KB of data in writable EEPROM divided into banks, and can handle over 100,000 re-writes. You can use our PN532 NFC/RFID breakout board or Adafruit NFC/RFID Shield for Arduino to read and write data to the EEPROM inside the tag. There is also a permanent 4-byte ID burned into the chip that you can use to identify one tag from another - the ID number cannot be changed.

These use a ISO/IEC 14443 Type A chipset, which used to be the 'classic' NFC chipset. In ~2014, the NFC forum decided not to support this chipset anymore, so newer phones do not support it. This only matters if you're trying to use this tag with a phone/tablet. Technical Details
• RFID chip specification:
o 1 KiloByte 8 KiloBit non-volatile EEPROM storage o Built in encryption engine with 48-bit key o 4 Byte unique identifier burned into the chip o MHz frequency Tag specification o Max Dimensions 22.11mm / round x / long o Head Dimensions 22.11mm / round x 4.06mm / thick o Shaft Dimensions 6mm / round x 38.23mm / long o 2.32g o Works about 2" away from reader

Engineered in NYC Adafruit

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 1483 Datasheet file may be downloaded here without warranties.

1483

1483 Datasheet

Datasheet ID: 1483 506778