63811-0600

63811-0600 Datasheet

63811-0600 Hand Crimp Tool for “Sabre” Flat Blade Male Terminals

Part	Datasheet
63811-0600	63811-0600 (pdf)

PDF Datasheet Preview
63811-0600 Hand Crimp Tool for “Sabre” Flat Blade Male Terminals HAND CRIMP TOOL SPECIFICATION SHEET Order No. 63811-0600 TYPE 2 Small handle spread which make this style tool ideally suited for end users Ratchet with safety release that ensures consistent performance A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position SCOPE Terminal Wire Size Insulation Diameter Strip Length Series No. AWG mm 43178-100* 18 - - - DEFINITION OF TERMS BRUSH BELL MOUTH INSULATION CRIMP SEAM BEND UP ROLLING STRIP LENGTH CUT-OFF TAB BEND DOWN CONDUCTOR CRIMP COND.CRIMP HEIGHT TWISTING The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. CONDITIONS: After crimping, the conductor profiles should measure the following see notes on page Terminal Wire Size Series No. 43178-100* 18 Cond. Crimp Height Ref Punch Width Ref Cond. Pull Force Min. Profile N Lb. A B Doc No ATS-638110600 Release Date 10-27-95 UNCONTROLLED COPY 63811-0600 Hand Crimp Tool for “Sabre” Flat Blade Male Terminals OPERATION Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will release the handles and the hand tool will spring open. Crimping Terminals Figure 1 Lift the locator blade and place the terminal into the correct die profile A or B , release the locator blade. Not all tools are equipped with a locator or locator blade. Partially close the tool until the terminal is held in place, See Figure Figure 2 Place a wire into the terminal and up against the locator blade. See Figure On tools without locators line the wire up with the conductor and insulation grips visually.

PDF Datasheet Preview

63811-0600 Hand Crimp Tool for “Sabre” Flat Blade Male Terminals

HAND CRIMP TOOL SPECIFICATION SHEET Order No. 63811-0600

TYPE 2

Small handle spread which make this style tool ideally suited for end users Ratchet with safety release that ensures consistent performance A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position

SCOPE

Terminal Wire Size Insulation Diameter

Strip Length

Series No. AWG mm
43178-100* 18 - - -

DEFINITION OF TERMS

BRUSH

BELL MOUTH

INSULATION CRIMP

SEAM

BEND UP ROLLING

STRIP LENGTH

CUT-OFF TAB

BEND DOWN

CONDUCTOR CRIMP COND.CRIMP HEIGHT

TWISTING

The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope.

CONDITIONS:

After crimping, the conductor profiles should measure the following see notes on page

Terminal Wire Size

Series No.
43178-100* 18

Cond. Crimp Height Ref

Punch Width Ref Cond.

Pull Force Min. Profile

N Lb. A B

Doc No ATS-638110600 Release Date 10-27-95

UNCONTROLLED COPY
63811-0600 Hand Crimp Tool for “Sabre” Flat Blade Male Terminals

OPERATION

Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will release the handles and the hand tool will spring open.

Crimping Terminals

Figure 1

Lift the locator blade and place the terminal into the correct die profile A or B , release the locator blade. Not all tools are equipped with a locator or locator blade.

Partially close the tool until the terminal is held in place, See Figure

Figure 2

Place a wire into the terminal and up against the locator blade. See Figure On tools without locators line the wire up with the conductor and insulation grips visually.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 63811-0600 Datasheet file may be downloaded here without warranties.

Datasheet ID: 63811-0600 649667