MIKROE-2355

MIKROE-2355 Datasheet

From MikroElektonika Documentation

Part	Datasheet
MIKROE-2355	MIKROE-2355 (pdf)

PDF Datasheet Preview
Ozone click From MikroElektonika Documentation Ozone click carries a MiCS-2614 compact MOS sensor for ozone O3 detection. Its detection range is from 10-1000ppb. Features and usage notes Ozone click Ozone click is a small 5 x 7 x 1.55mm MEMS sensor consisting of a micro machined diaphragm with an embedded heating resistor and the sensing layer on top. Schematic also available in PDF The sensor outputs an analog voltage, which is converted by the onboard MCP3201 12-bit ADC converter. The MCP3201 is typically used as a sensor interface for data acquisition. It’s capable of outputting sample rates of up to 100 ksps at a clock rate of MHz. The click communicates with the target MCU through the mikroBUS SPI interface CS, SCK, MISO . The board is designed to use a 5V power supply only. Note that the sensing layer is sensitive to various external factors. For example, it must not be exposed to high concentrations of organic solvents, silicone vapours or cigarette-smoke. Otherwise it might damage the sensitive layer and diminish the accuracy of the sensor. Programming The following code snippet reads off the sensor data every 500 milliseconds. Ozone click IC/Module MiCS-2614 Interface SPI Power 5V supply Website 1 void main 3 system_init ; 4 display_init ; 6 while 1 measurement ; calculation ; display_result ; delay_ms 500 ; Code examples that demonstrate the usage of Ozone click with MikroElektronika hardware, written for mikroC for ARM, AVR, dsPIC, FT90x, PIC and PIC32 are available on Libstock Resources - Vendor’s data sheet - mikroBUS standard specifications Retrieved from This page was last modified on 11 July 2016, at Content is available under Creative Commons Attribution unless otherwise noted. 8/8/2016

PDF Datasheet Preview

Ozone click

From MikroElektonika Documentation

Ozone click carries a MiCS-2614 compact MOS sensor for ozone O3 detection. Its detection range is from 10-1000ppb.

Features and usage notes

Ozone click

Ozone click is a small 5 x 7 x 1.55mm MEMS sensor consisting of a micro machined diaphragm with an embedded heating resistor and the sensing layer on top.

Schematic also available in PDF

The sensor outputs an analog voltage, which is converted by the onboard MCP3201 12-bit ADC converter. The MCP3201 is typically used as a sensor interface for data acquisition. It’s capable of outputting sample rates of up to 100 ksps at a clock rate of MHz.

The click communicates with the target MCU through the mikroBUS SPI interface CS, SCK, MISO . The board is designed to use a 5V power supply only.

Note that the sensing layer is sensitive to various external factors. For example, it must not be exposed to high concentrations of organic solvents, silicone vapours or cigarette-smoke. Otherwise it might damage the sensitive layer and diminish the accuracy of the sensor.

Programming

The following code snippet reads off the sensor data every 500 milliseconds.

Ozone click

IC/Module MiCS-2614

Interface SPI

Power 5V supply

Website
1 void main
3 system_init ;
4 display_init ;
6 while 1
measurement ;
calculation ;
display_result ;
delay_ms 500 ;

Code examples that demonstrate the usage of Ozone click with MikroElektronika hardware, written for mikroC for ARM, AVR, dsPIC, FT90x, PIC and PIC32 are available on Libstock

Resources
- Vendor’s data sheet - mikroBUS standard specifications

Retrieved from

This page was last modified on 11 July 2016, at Content is available under Creative Commons Attribution unless otherwise noted.
8/8/2016

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MIKROE-2355 Datasheet file may be downloaded here without warranties.

Datasheet ID: MIKROE-2355 649478