MIKROE-2846

MIKROE-2846 Datasheet

PID MIKROE-2846

Part	Datasheet
MIKROE-2846	MIKROE-2846 (pdf)

PDF Datasheet Preview
ADC 5 click PID MIKROE-2846 Weight 24 g ADC 5 click is a device used to sample an analog voltage on the input and convert it to a digital information. In general, ADC analog to digital converters are the most commonly used devices for converting the voltage signals into an information, which can be then processed in the digital domain. There are many types of ADC converters commercially available. They can vary in bit depth, sample rate, used approximation algorithm SAR, delta-sigma... and so on. Those attributes affect how accurately the sampled voltage will be translated into the digital world. ADC 5 click uses the ADC121S021 device from Texas Instruments - a low power, single channel 12-bit CMOS analog to digital converter, with a high-speed serial interface. This device uses the SAR algorithm for sampling the input voltage which, coupled with relatively high bit depth, gives a pretty accurate digital reconstruction of the input voltage. How does it work? The ADC 5 click is equipped with the ADC121S021, a 12-bit CMOS ADC device from Texas Instruments. This AD converter is using a reference voltage obtained from the LP2985 LDO regulator from the same company, which provides a clean and accurate regulated voltage on its output, perfectly suited to be used as the reference voltage for this converter. Since the reference voltage is set to 3.3V, the maximum value of the input voltage is also 3.3V. The device uses the SPI communication. The MOSI pin does not exist, since no communication from the MCU to the click board is going on. The reading speed, also known as the sample rate, directly depends on the clock rate of the SCK line. The sample rate over which the specified electrical performance is ensured is 50 Ks/s to 200 Ks/s. The ADC121S021 has the ability to use any clock signal frequency up to the rated maximum frequency, so the sample rate can be changed continuously. The sample rate is usually the determining factor when the maximum frequency of the input signal is considered. The aliasing of the input signal can occur as the input signal frequency is nearing half the sample rate of the converter. The bandwidth of the input signal is limited by this frequency, also called the Nyquist frequency, so using input frequencies beyond the Nyquist frequency, results with a very inaccurate conversion. ADC converters in general, use a range of different mechanisms to convert the voltage on their input terminals. The ADC121S021 AD converter uses the SAR, or the successive approximation method for the conversion, which consists of comparing the input voltage with a series of internally generated voltage values. At each step in this process, the approximation is stored in a successive approximation register. The comparing steps are continued until the desired resolution is reached. The ADC click board is also equipped with the screw terminal which can be used for easy and secure connection of the input voltage rail. Although the reference voltage is 3.3V, it is powered only by the 5V rail from the mikroBUS , used as the input for the LDO regulator. Specifications Type ADC 5 click can be used to digitally convert input voltage signals up to 3.3V so that the signals can be analyzed by various mathematical models and algorithms on the CPU or MCU. On-board modules ADC121S021 a single channel, 50ks/s to 200Ks/s, a 12-Bit SAR ADC, LP2950 - micropower voltage regulator with low voltage drop, both made by Texas Instruments. Key Features The ADC 5 click specified to work with sample rates from 50Ks/s to 200Ks/s. It uses a precise LDO as a reference voltage source and SAR approximation method of sampling Interface Input Voltage 5V Click board size M x mm Pinout diagram This table shows how the pinout on ADC 5 click corresponds to the pinout on the mikroBUS socket the latter shown in the two middle columns . Notes Chip select SPI clock SPI data output Ground NC 1 AN PWM 16 NC NC 2 RST INT 15 NC CS 3 CS 14 NC SCK 4 SCK TX 13 NC SDO 5 MISO SCL 12 NC NC 6 MOSI SDA 11 NC NC 7 3.3V 5V 10 +5V Power supply GND 8 GND 9 GND Ground ADC 5 click electrical specifications Min Typ Max Unit Vin analog input ADC reference voltage Onboard settings and indicators

PDF Datasheet Preview

ADC 5 click

PID MIKROE-2846

Weight 24 g

ADC 5 click is a device used to sample an analog voltage on the input and convert it to a digital information. In general, ADC analog to digital converters are the most commonly used devices for converting the voltage signals into an information, which can be then processed in the digital domain. There are many types of ADC converters commercially available. They can vary in bit depth, sample rate, used approximation algorithm SAR, delta-sigma... and so on. Those attributes affect how accurately the sampled voltage will be translated into the digital world.

ADC 5 click uses the ADC121S021 device from Texas Instruments - a low power, single channel 12-bit CMOS analog to digital converter, with a high-speed serial interface. This device uses the SAR algorithm for sampling the input voltage which, coupled with relatively high bit depth, gives a pretty accurate digital reconstruction of the input voltage.

How does it work?

The ADC 5 click is equipped with the ADC121S021, a 12-bit CMOS ADC device from Texas Instruments. This AD converter is using a reference voltage obtained from the LP2985 LDO regulator from the same company, which provides a clean and accurate regulated voltage on its output, perfectly suited to be used as the reference voltage for this converter. Since the reference voltage is set to 3.3V, the maximum value of the input voltage is also 3.3V. The device uses the SPI communication. The MOSI pin does not exist, since no communication from the MCU to the click board is going on. The reading speed, also known as the sample rate, directly depends on the clock rate of the SCK line. The sample rate over which the specified electrical performance is ensured is 50 Ks/s to 200 Ks/s. The ADC121S021 has the ability to use any clock signal frequency up to the rated maximum frequency, so the sample rate can be changed continuously. The sample rate is usually the determining factor when the maximum frequency of the input signal is considered. The aliasing of the input signal can occur as the input signal frequency is nearing half the sample rate of the converter. The bandwidth of the input signal is limited by this frequency, also called the Nyquist frequency, so using input frequencies beyond the Nyquist frequency, results with a very inaccurate conversion.

ADC converters in general, use a range of different mechanisms to convert the voltage on their input terminals. The ADC121S021 AD converter uses the SAR, or the successive approximation method for the conversion, which consists of comparing the input voltage with a series of internally generated voltage values. At each step in this process, the approximation is stored in a successive approximation register. The comparing steps are continued until the desired resolution is reached. The ADC click board is also equipped with the screw terminal which can be used for easy and secure connection of the input voltage rail. Although the reference voltage is 3.3V, it is powered only by the 5V rail from the mikroBUS , used as the input for the LDO regulator.

Specifications

Type

ADC 5 click can be used to digitally convert input voltage signals up to 3.3V so that the signals can be analyzed by various mathematical models and algorithms on the CPU or MCU.

On-board modules

ADC121S021 a single channel, 50ks/s to 200Ks/s, a 12-Bit SAR ADC, LP2950 - micropower voltage regulator with low voltage drop, both made by Texas Instruments.

Key Features

The ADC 5 click specified to work with sample rates from 50Ks/s to 200Ks/s. It uses a precise LDO as a reference voltage source and SAR approximation method of sampling

Interface

Input Voltage 5V

Click board size

M x mm

Pinout diagram

This table shows how the pinout on ADC 5 click corresponds to the pinout on the mikroBUS socket the latter shown in the two middle columns .

Notes

Chip select SPI clock SPI data output

Ground

NC 1 AN

PWM 16 NC

NC 2 RST INT 15 NC

CS 3 CS
14 NC

SCK 4 SCK TX
13 NC

SDO 5 MISO SCL 12 NC

NC 6 MOSI SDA 11 NC

NC 7 3.3V 5V
10 +5V Power supply

GND 8 GND 9 GND Ground

ADC 5 click electrical specifications

Min Typ Max Unit

Vin analog input

ADC reference voltage

Onboard settings and indicators

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MIKROE-2846 Datasheet file may be downloaded here without warranties.

Datasheet ID: MIKROE-2846 649456