MIKROE-2523

MIKROE-2523 Datasheet

PID MIKROE-2523 Weight 27 g

Part	Datasheet
MIKROE-2523	MIKROE-2523 (pdf)

PDF Datasheet Preview
AC Current click PID MIKROE-2523 Weight 27 g AC Current click can measure alternating currents up to 30A and it features the MCP3201 ADC analog to digital converter and the MCP607 CMOS Op Amp, both from Microchip. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target MCU over an SPI interface, and the AN pin on the mikroBUS line. AC Current click can only be used for sensors with voltage output 30A input current 1V output voltage amplitude . If someone wants to measure current with a sensor for a different range 10A or 100A , then it is necessary to change the multiplication constant in firmware. Note This click board can be used for measuring current from a High-Voltage alternating source, so it is important to know that there is danger from electric shock. Note AC Current click does not include the non-invasive AC current sensor. Take a look at the AC Current click - bundle, if you want to buy both the sensor and the click. MCP3201 ADC converter MCP3210 ADC converter is a 12-bit Analog-to-Digital converter. The device provides a single pseudo-differential input. The converter is capable of sample rates of up to 100 ksps at a clock rate of MHz. The MCP3201 device operates over a broad voltage range 2.7V-5.5V . Low-current design permits operation with typical standby and active currents of only 500 nA and300 uA, respectively. MCP607 CMOS Operational Amplifier MCP607 operational amplifier is unity-gain stable with a low offset voltage 250 uV, maximum . Performance characteristics include rail-to-rail output swing capability and low input bias current 80 pA at +85°C, maximum . Analog output There is an Analog output for users who want to side step the onboard ADC and use an ADC from a microcontroller instead. One wire measurement To measure current using this click it is necessary to put one wire through the sensor, not both. How it works When current flows through the sensor there is the same voltage waveform at the output of the sensor usually sinusoidal . The first stage on the click board is the Low-Pass filter whose role is the suppression of radio waves and other noise from large cable from sensor to the click board . The R1 from the LowPass filter and the R2 make the voltage divider. After the Low-Pass filter there is the operational amplifier, which is powered by single supply voltage. Because of the single supply this operational amplifier can amplify only the positive part of signal rectifier . Gain is defined by the R4 and R3: The next stage is another Low-Pass filter which has to make continual DC voltage, which can be used to calculate the input current. The 12bit ADC is used to convert voltage to digital data. Development board MCU communicates with the ADC using SPI and calculates RMS of input current. Key features • 3.5mm jack • measurement • MCP3201 ADC converter o resolution o 100 ksps Maximum Sampling Rate at VDD = 5V o 50 ksps Maximum Sampling Rate at VDD = 2.7V o 500 nA Typical Standby Current, 2 uA Maximum o 400 uA Maximum Active Current at 5V • MCP607 Op Amp o Stable o Low Input Offset Voltage 250 uV maximum o Low Input Bias Current 80 pA maximum at +85°C • Interface SPI • 3.3V or 5V power supply SPECIFICATION Product Type On-board modules Key Features Key Benefits Interface Power Supply Compatibility Click board size Measurements One phase measuring from the power line 110/220V or some other alternating voltage/current source, power consumption measurement, current monitoring over the analog output . MCP3201, MCP607 Non-invasive measurement, 12-bit resolution MCP3201 ADC converter, the click measures alternating currents up to 30A , MCP607 CMOS Op Amp Non-invasive measurement SPI 3.3V or 5V mikroBUS M x mm Pinout diagram This table shows how the pinout on AC Current click corresponds to the pinout on the mikroBUS socket the latter shown in the two middle columns . Notes Pin Notes mikroBUStm Analog AN 1 AN PWM 16 NC Not connected Not connected NC 2 RST INT 15 NC Not connected Chip select/Shutdown input CS 3 CS TX 14 NC Not connected SPI clock SCK 4 SCK RX 13 NC Not connected Serial data out MISO 5 MISO SCL 12 NC Not connected Not connected NC 6 MOSI SDA 11 NC Not connected Power supply +3.3V 7 3.3V 5V 10 +5V Power supply Ground GND 8 GND 9 GND Ground Onboard jumpers The table below shows information about onboard jumpers: Designator Name Default Position Default Option JP1 PWR.SEL. Left 3.3V Power Supply Voltage Selection 3.3V/5V, left position 3.3V, right position 5V Programming This code snippet initializes MCU, AC Current click board and measures and shows current value in mA. 01 void main

PDF Datasheet Preview

AC Current click

PID MIKROE-2523 Weight 27 g

AC Current click can measure alternating currents up to 30A and it features the MCP3201 ADC analog to digital converter and the MCP607 CMOS Op Amp, both from Microchip. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target MCU over an SPI interface, and the AN pin on the mikroBUS line. AC Current click can only be used for sensors with voltage output 30A input current 1V output voltage amplitude . If someone wants to measure current with a sensor for a different range 10A or 100A , then it is necessary to change the multiplication constant in firmware. Note This click board can be used for measuring current from a High-Voltage alternating source, so it is important to know that there is danger from electric shock. Note AC Current click does not include the non-invasive AC current sensor. Take a look at the AC Current click - bundle, if you want to buy both the sensor and the click.

MCP3201 ADC converter MCP3210 ADC converter is a 12-bit Analog-to-Digital converter. The device provides a single pseudo-differential input. The converter is capable of sample rates of up to 100 ksps at a clock rate of MHz. The MCP3201 device operates over a broad voltage range 2.7V-5.5V . Low-current design permits operation with typical standby and active currents of only 500 nA and300 uA, respectively. MCP607 CMOS Operational Amplifier MCP607 operational amplifier is unity-gain stable with a low offset voltage 250 uV, maximum . Performance characteristics include rail-to-rail output swing capability and low input bias current 80 pA at +85°C, maximum . Analog output There is an Analog output for users who want to side step the onboard ADC and use an ADC from a microcontroller instead. One wire measurement To measure current using this click it is necessary to put one wire through the sensor, not both.

How it works When current flows through the sensor there is the same voltage waveform at the output of the sensor usually sinusoidal . The first stage on the click board is the Low-Pass filter whose role is the suppression of radio waves and other noise from large cable from sensor to the click board . The R1 from the LowPass filter and the R2 make the voltage divider. After the Low-Pass filter there is the operational amplifier, which is powered by single supply voltage. Because of the single supply this operational amplifier can amplify only the positive part of signal rectifier . Gain is defined by the R4 and R3:

The next stage is another Low-Pass filter which has to make continual DC voltage, which can be used to calculate the input current.

The 12bit ADC is used to convert voltage to digital data. Development board MCU communicates with the ADC using SPI and calculates RMS of input current.

Key features
• 3.5mm jack
• measurement
• MCP3201 ADC converter
o resolution o 100 ksps Maximum Sampling Rate at VDD = 5V o 50 ksps Maximum Sampling Rate at VDD = 2.7V o 500 nA Typical Standby Current, 2 uA Maximum o 400 uA Maximum Active Current at 5V
• MCP607 Op Amp o Stable o Low Input Offset Voltage 250 uV maximum o Low Input Bias Current 80 pA maximum at +85°C
• Interface SPI
• 3.3V or 5V power supply

SPECIFICATION

Product Type

On-board modules

Key Features

Key Benefits Interface Power Supply Compatibility Click board size

Measurements One phase measuring from the power line 110/220V or some other alternating voltage/current source, power consumption measurement, current monitoring over the analog output .

MCP3201, MCP607

Non-invasive measurement, 12-bit resolution MCP3201 ADC converter, the click measures alternating currents up to 30A , MCP607 CMOS Op Amp Non-invasive measurement SPI 3.3V or 5V mikroBUS

M x mm

Pinout diagram

This table shows how the pinout on AC Current click corresponds to the pinout on the mikroBUS socket the latter shown in the two middle columns .

Notes

Pin Notes
mikroBUStm

Analog AN 1 AN PWM 16 NC Not connected

Not connected NC 2 RST INT 15 NC Not connected

Chip select/Shutdown input CS 3 CS TX 14 NC Not connected

SPI clock SCK 4 SCK RX 13 NC Not connected

Serial data out MISO 5 MISO SCL 12 NC Not connected

Not connected NC 6 MOSI SDA 11 NC Not connected

Power supply +3.3V 7 3.3V 5V 10 +5V Power supply

Ground GND 8 GND 9 GND Ground

Onboard jumpers The table below shows information about onboard jumpers:

Designator Name

Default Position

Default Option

JP1 PWR.SEL. Left
3.3V Power Supply Voltage Selection 3.3V/5V, left position 3.3V, right position 5V

Programming

This code snippet initializes MCU, AC Current click board and measures and shows current value in mA.
01 void main

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MIKROE-2523 Datasheet file may be downloaded here without warranties.

Datasheet ID: MIKROE-2523 649360