PD69100C-GGGG

PD69100C-GGGG Datasheet

Microsemi’s PoE controller, PD69100, is a costeffective, pre-programmed unit designed to implement Enhanced mode. It is used in conjunction with Microsemi’s PoE Managers PD69108 and PD69104 in Ethernet switches to enable next generation network devices to share power and data over the same cable, as specified in IEEE802.3af and IEEE802.3at standards. Enhanced mode operation along with PD69108/PD69104 managers enables operation in a total Power-over-Ethernet standalone mode.

Part	Datasheet
PD69100C-GGGG	PD69100C-GGGG (pdf)

Related Parts	Information
PD69100R-GGGG	PD69100R-GGGG

PDF Datasheet Preview
W.Microsemi .CO M Microsemi’s PoE controller, PD69100, is a costeffective, pre-programmed unit designed to implement Enhanced mode. It is used in conjunction with Microsemi’s PoE Managers PD69108 and PD69104 in Ethernet switches to enable next generation network devices to share power and data over the same cable, as specified in IEEE802.3af and IEEE802.3at standards. Enhanced mode operation along with PD69108/PD69104 managers enables operation in a total Power-over-Ethernet standalone mode. The controller features an ESPI bus for each PoE device and a communication interface with Host CPU via UART or I2C protocol. Device is based on STMicroelectronics family STM32F101T6 embedded with ARM Cortex -M3 core. It includes the following peripherals: • 3 x Timers • 2 x Uarts • 1 x SPI • 1 x I2C • 1 x 12-bit analog-to-digital converter PIN CONFIGURATION VDD2 VSS2 SWDIO xLED_OE xLED_Latch I2C_Message_Ready xInt_Out xLED_CS VDD1 27 26 25 24 23 22 21 20 19 SWCLK 28 xDisable_Ports 29 xHswp_On 30 Spare 31 xSys_OK 32 SCL / UART1_TX 33 SDA / UART1_RX 34 Boot0 35 VSS3 36 <Part Number > < -Software Ver > < Date Code > 12 3 4 5 6 7 8 9 18 VSS1 17 Reserved 16 I2C_ADDR 15 HW_VER 14 ESPI_MOSI 13 ESPI_MISO 12 ESPI_SCK 11 ESPI_xCS 10 Reserved PD69100 PoE Controller Unit DATASHEET KEY FEATURES Controls up to 48 PoE ports 6 x PD69108 Pre-Standard / Capacitor detection of Cisco devices Supports both UART and I2C interfaces to Host CPU Backwards compatible with PD69000, PD63000, PD62000 and PDIC66000 Supports 2 pair RJ or 4 pair RJ 16 power banks support using four discrete lines connected directly to PD69108 / PD69104. Power management for up to 96 ports Rmode pin for default parameters selection Programmable over-voltage and under voltage Predefined power budget 16 discrete levels LED stream support System OK indication Software download via I2C or UART System and port measurements Detailed port status Thermal protection and monitoring Programmable temperature alarm limit Interrupt out pin for system and port events Forced power for system testing System reset Port power limit setting Port matrix and priority Automatic PoE device type detection RoHS compliant MARKETING DEFINITIONS Device’s label includes the following <Part number> Hardware P/N for example PD69100 <-Software Ver> Software version for example. 0120 <Date Code> Burning date code in the following format yyww yy = year, ww = week FIRMWARE DOWNLOAD Initial burning of controller's firmware is performed in factory. Firmware upgrades can be performed by users using communication interface see application note 126 catalogue number PD69100 VDD3 OSC_IN OSC_OUT xRESET VSSA VDDA Spare_Analog Rmode Reserved ORDERING INFORMATION Part Number PD69100y-gggg Detection y = R Resistor y = C Resistor/legacy Version gggg *For latest firmware version available, refer to Microsemi's website or Customer Care Support. Copyright 2010 Microsemi Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA Within the USA 800 713-4113, Outside the USA 949 221-7100 Fax 949 756-0308 W.Microsemi .CO M PD69100 PoE Controller Unit DATASHEET APPLICABLE DOCUMENTS IEEE 802.3af-2003 standard, DTE Power via MDI IEEE 802.3at-2009 standard, DTE Power via MDI Microsemi PD69108 datasheet , catalogue number DS_PD69108 Microsemi PD69104 datasheet , catalogue number DS_PD69104 Microsemi Serial communication protocol user guide , catalogue number 06-0054-080 Microsemi application note 174 for Designing 48-port Enhanced PoE System 802.3af/802.3at Compliant , catalogue number 06-0054-080 Microsemi Application note 126 Software Download for PoE Units, catalogue number 06-0006-080 ST-Microelectornics STM32F101x6 datasheet PIN FUNCTIONALITY PIN NAME VDD3 OSC_IN OSC_OUT xRESET NRST VSSA VDDA Spare_Analog Rmode Reserved ESPI_xCS ESPI_SCK ESPI_MISO ESPI_MOSI HW_VER I2C_ADDR Reserved VSS1 VDD1 xLed_Cs PIN TYPE Supply Oscillator IN AGND Supply Analog_IN Analog_IN OUT IN OUT IN OUT Analog_IN IN DGND Supply OUT PIN DESCRIPTION Main Supply 3.3V Oscillator Input Oscillator Output Reset Input Analog Ground Main Supply 3.3V N/A Pre Defined Power Budget Settings Software Debug Uart Software Debug Uart ESPI Bus to PoE Manager ESPI Bus to PoE Manager ESPI Bus to PoE Manager ESPI Bus to PoE Manager Hardware Version I2C address of PD69100 Not Used Must be Puledl Up Digital Ground Main Supply 3.3V Chip Select for LED Stream PIN NAME xInt_Out I2C_Message_ Ready xLED_Latch xLED_OE SWDIO VSS2 VDD2 SWCLK xDisable_Ports xHswp_On Spare xSys_OK SCL / UART1_Tx SDA / UART1_RX Boot0 VSS3 TYPE DESCRIPTION Interrupt Output Indication Signals message is ready to be read by Host, Latch for LED stream Enable for status LED DEBUG Serial Debug Data Bus DGND Digital Ground Supply DEBUG Ordering information update Updating template and proofing 2009 Microsemi Corp. All rights reserved. For support contact Visit our web site at: Cat. No. DS_PD69100 PD69100 Copyright 2010 Microsemi Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA Within the USA 800 713-4113, Outside the USA 949 221-7100 Fax 949 756-0308

PDF Datasheet Preview

W.Microsemi .CO M

Microsemi’s PoE controller, PD69100, is a costeffective, pre-programmed unit designed to implement Enhanced mode. It is used in conjunction with Microsemi’s PoE Managers PD69108 and PD69104 in Ethernet switches to enable next generation network devices to share power and data over the same cable, as specified in IEEE802.3af and IEEE802.3at standards. Enhanced mode operation along with PD69108/PD69104 managers enables operation in a total Power-over-Ethernet standalone mode.

The controller features an ESPI bus for each PoE device and a communication interface with Host CPU via UART or I2C protocol.

Device is based on STMicroelectronics family STM32F101T6 embedded with ARM Cortex -M3 core. It includes the following peripherals:
• 3 x Timers
• 2 x Uarts
• 1 x SPI
• 1 x I2C
• 1 x 12-bit analog-to-digital converter

PIN CONFIGURATION

VDD2 VSS2 SWDIO xLED_OE xLED_Latch I2C_Message_Ready xInt_Out xLED_CS VDD1
27 26 25 24 23 22 21 20 19

SWCLK 28 xDisable_Ports 29
xHswp_On 30 Spare 31
xSys_OK 32 SCL / UART1_TX 33 SDA / UART1_RX 34

Boot0 35 VSS3 36
<Part Number > < -Software Ver > < Date Code >
12 3 4 5 6 7 8 9
18 VSS1 17 Reserved 16 I2C_ADDR 15 HW_VER 14 ESPI_MOSI 13 ESPI_MISO 12 ESPI_SCK 11 ESPI_xCS 10 Reserved

PD69100

PoE Controller Unit

DATASHEET

KEY FEATURES Controls up to 48 PoE ports 6 x PD69108 Pre-Standard / Capacitor detection of Cisco devices Supports both UART and I2C interfaces to

Host CPU Backwards compatible with PD69000,

PD63000, PD62000 and PDIC66000 Supports 2 pair RJ or 4 pair RJ 16 power banks support using four discrete
lines connected directly to PD69108 / PD69104. Power management for up to 96 ports Rmode pin for default parameters selection Programmable over-voltage and under voltage Predefined power budget 16 discrete levels LED stream support System OK indication Software download via I2C or UART System and port measurements Detailed port status Thermal protection and monitoring Programmable temperature alarm limit Interrupt out pin for system and port events Forced power for system testing System reset Port power limit setting Port matrix and priority Automatic PoE device type detection RoHS compliant

MARKETING DEFINITIONS Device’s label includes the following <Part number> Hardware P/N for example

PD69100 <-Software Ver> Software version for
example. 0120 <Date Code> Burning date code in the
following format yyww yy = year, ww = week

FIRMWARE DOWNLOAD

Initial burning of controller's firmware is performed in factory. Firmware upgrades can be performed by users using communication interface see application note 126 catalogue number

PD69100

VDD3 OSC_IN OSC_OUT xRESET

VSSA VDDA Spare_Analog Rmode Reserved
ORDERING INFORMATION

Part Number PD69100y-gggg

Detection
y = R Resistor y = C Resistor/legacy

Version
gggg
*For latest firmware version available, refer to Microsemi's website or Customer Care Support.

Copyright 2010

Microsemi

Analog Mixed Signal Group
2381 Morse Avenue, Irvine, CA 92614, USA Within the USA 800 713-4113, Outside the USA 949 221-7100 Fax 949 756-0308

W.Microsemi .CO M

PD69100

PoE Controller Unit

DATASHEET

APPLICABLE DOCUMENTS IEEE 802.3af-2003 standard, DTE Power via MDI IEEE 802.3at-2009 standard, DTE Power via MDI Microsemi PD69108 datasheet , catalogue number DS_PD69108 Microsemi PD69104 datasheet , catalogue number DS_PD69104 Microsemi Serial communication protocol user guide , catalogue number 06-0054-080 Microsemi application note 174 for Designing 48-port Enhanced PoE System 802.3af/802.3at Compliant ,
catalogue number 06-0054-080 Microsemi Application note 126 Software Download for PoE Units, catalogue number 06-0006-080 ST-Microelectornics STM32F101x6 datasheet

PIN FUNCTIONALITY

PIN NAME

VDD3 OSC_IN OSC_OUT xRESET NRST VSSA VDDA Spare_Analog

Rmode Reserved ESPI_xCS ESPI_SCK ESPI_MISO ESPI_MOSI HW_VER I2C_ADDR Reserved VSS1 VDD1 xLed_Cs

PIN TYPE

Supply Oscillator

IN AGND Supply Analog_IN

Analog_IN OUT IN OUT IN OUT Analog_IN IN DGND Supply OUT

PIN DESCRIPTION

Main Supply 3.3V Oscillator Input Oscillator Output

Reset Input Analog Ground Main Supply 3.3V N/A Pre Defined Power Budget Settings Software Debug Uart Software Debug Uart ESPI Bus to PoE Manager ESPI Bus to PoE Manager ESPI Bus to PoE Manager ESPI Bus to PoE Manager Hardware Version I2C address of PD69100 Not Used Must be Puledl Up Digital Ground Main Supply 3.3V Chip Select for LED Stream

PIN NAME
xInt_Out I2C_Message_ Ready xLED_Latch xLED_OE SWDIO VSS2 VDD2

SWCLK xDisable_Ports
xHswp_On

Spare xSys_OK SCL / UART1_Tx SDA / UART1_RX

Boot0 VSS3

TYPE DESCRIPTION

Interrupt Output Indication Signals message is ready to be read by Host,

Latch for LED stream

Enable for status LED

DEBUG Serial Debug Data Bus

DGND Digital Ground

Supply DEBUG
Ordering information update

Updating template and proofing
2009 Microsemi Corp.

All rights reserved.

For support contact Visit our web site at:

Cat. No. DS_PD69100

PD69100

Copyright 2010

Microsemi

Analog Mixed Signal Group
2381 Morse Avenue, Irvine, CA 92614, USA Within the USA 800 713-4113, Outside the USA 949 221-7100 Fax 949 756-0308

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived PD69100C-GGGG Datasheet file may be downloaded here without warranties.

Datasheet ID: PD69100C-GGGG 649099