KSZ8864RMNUB-EVAL

KSZ8864RMNUB-EVAL Datasheet

KSZ8864 Evaluation Board User’s Guide

Part	Datasheet
KSZ8864RMNUB-EVAL	KSZ8864RMNUB-EVAL (pdf)

PDF Datasheet Preview
KSZ8864 Evaluation Board User’s Guide KSZ8864 Evaluation Board User’s Guide KSZ8864 Integrated 4-port 10/100 Ethernet Managed Switch Micrel Inc. 5/9/2014 KSZ8864 Evaluation Board User’s Guide Table of contents Features 4 Evaluation Kit Contents 4 Hardware Description 5 Strap in Feature Setting Jumpers 7 EEPROM Mode 8 SPI Mode 9 10/100 Ethernet LED indicators 10 MII/RMII Port Configuration 10 Port 4 SW4-MII Jumper Configuration 11 Port 3 SW3-MII Jumper and Register Configuration 12 Port 4 SW4-RMII Jumper Configuration for KSZ8864 12 Port 3 SW3-RMII Jumper Configuration for KSZ8864 13 MDC/MDIO Interface for MIIM Registers and SMI mode 13 Software Description 15 Introducing Application Software Tools 15 Install Window Driver First 15 DOS SPI Tool 18 MDC/MDIO MIIM Software Tool 19 MDC/MDIO MII software installation 19 On board jumper setting and Software Application 19 MDC/MDIO SMI Software 21 MDC/MDIO SMI On board jumper setting and Software Application 21 EEPROM Software Tool 22 EEPROM software On board jumper setting and Software Application 22 Window SPI Software Tool 25 Window SPI software installation 25 On board jumper setting and Software Application 25 Reference Documents 26 Bill of Micrel Inc. 5/9/2014 KSZ8864 Evaluation Board User’s Guide List of Figures and Tables Figure 1 KSZ8864 Evaluation Board 5 Figure 2 KSZ8864 Evaluation Board Block Diagram 6 Table 1 Feature Setting Table 2 Reserved Jumpers 8 Table 3 EEPROM Mode Settings 8 Table 4 SPI Mode Settings 9 Table 5 LED Table 6 SCONF [1:0] pin [47,48] for SW4-MII PHY/MAC Table 7 Configure for SW4-MII 11 Table 8 Configure for SW3-MII 12 Table 9 Configure for SW4-RMII 12 Table 10 Configure for SW3-RMII 13 Table 11 MDC/MDIO Settings for MIIM 14 Table 12 MDC/MDIO Settings for SMI 14 Date 10/21/10 05/09/14 Micrel Inc. 5/9/2014 KSZ8864 Evaluation Board User’s Guide Introduction The KSZ8864 is Micrel Operations’ new generation integrated 4-port switch with a 64-pin small package. The KSZ8864 device consists of two PHYs and four MACs. Two of MACs support either MII or RMII interfaces for dual processor/DSP data transfer. Higher speed SPI and MDC/MDIO interfaces can fully manage the 4-port switch by the processor. The device had been designed with cost sensitive systems in mind but still offers a multitude of features such as switch management port and tag based VLAN 1/2/4-queue QoS priority a dual MII/RMII option data interfaces and CPU control interfaces of SPI, MDC/MDIO with MIIM/SMI. MIIM is the standard IEEE MII Management Interface. SMI is non-standard Serial Management Interface that can access all registers by the Management Data Input/output MDIO interface. The KSZ8864 is an excellent choice in current complex Ethernet applications with single processor or dual processors, industrial automatic, automotive, etc. fields and as a standalone 4-port switch. The KSZ8864 evaluation board is designed to allow the user to experience first-hand the rich feature set of these existing 4-port switches of KSZ8864CNX/RMNUB. The evaluation board is highly configurable and easy to use. • Micrel KSZ8864 Integrated 4-port 10/100 Managed Ethernet Switch • 2 RJ-45 Jacks for Ethernet LAN with Corresponding Isolation Magnetics. • Auto MDI/MDIX on all Ports. • 1 PHY mode and 1 MAC mode 40-pin male/female connectors are for the port 3 Switch SW3-MII/RMII Interfaces. • 1 PHY mode and 1 MAC mode 40-pin male/female connectors are for the port 4 Switch SW4-MII/RMII Interfaces. • 1 USB Port Interface Configurable to emulate interfaces of EEPROM, SPI interface, MDC/MDIO with SMI Interface and access all MIIM registers. • On Board EEPROM • 2 LEDs Per Port to Indicate the Status and Activity • 5VDC, 2.5A Universal Power Supply Evaluation Kit Contents package in the Design Kit of the KSZ8864 Ethernet switch product on Micrel website. Contact your Micrel FAE for the latest schematic . • The USB cable is not included. Micrel Inc. 5/9/2014 KSZ8864 Evaluation Board User’s Guide Hardware Description The KSZ8864 evaluation board is in a compact form factor and can sit on a bench near a computer/laptop. There are three options for configuration strap in mode EEPROM mode and SPI mode. Strap in mode configuration is easily done with on board jumper options. EEPROM mode and SPI mode are accomplished through a built in USB port interface. Using Micrel EEPROM software and your PC, you can reprogram the EEPROM on board by the USB port. Or using Micrel SPI software and your PC, you can access the KSZ8864’s full feature set registers by the USB to SPI interface. The board also features the MII connectors for the Switch MII/RMII interface on port 3 and port These are to facilitate connections from the switch to an external MAC or PHY with MII/RMII interface. The KSZ8864 evaluation board is easy to use. There are programmable LED indicators for link and activity on all ports and a power LED. A manual reset button allows the user to reset the board without removing the power plug. A standard 5VDC power supply is included so that the user can supply power from any 110-240 Volt AC wall or bench socket, and the power also can be provided by USB port when close pin 2-3 of the JP47 jumper. Micrel Inc. Figure 1 KSZ8864 Evaluation Board Page 5 5/9/2014 KSZ8864 Evaluation Board User’s Guide 5 VDC Jack

PDF Datasheet Preview

KSZ8864 Evaluation Board User’s Guide

KSZ8864 Evaluation Board User’s Guide

KSZ8864 Integrated 4-port 10/100 Ethernet Managed Switch

Micrel Inc.
5/9/2014

KSZ8864 Evaluation Board User’s Guide

Table of contents

Features 4 Evaluation Kit Contents 4 Hardware Description 5

Strap in Feature Setting Jumpers 7

EEPROM Mode 8 SPI Mode 9 10/100 Ethernet LED indicators 10 MII/RMII Port Configuration 10

Port 4 SW4-MII Jumper Configuration 11 Port 3 SW3-MII Jumper and Register Configuration 12 Port 4 SW4-RMII Jumper Configuration for KSZ8864 12 Port 3 SW3-RMII Jumper Configuration for KSZ8864 13 MDC/MDIO Interface for MIIM Registers and SMI mode 13 Software Description 15 Introducing Application Software Tools 15 Install Window Driver First 15 DOS SPI Tool 18 MDC/MDIO MIIM Software Tool 19 MDC/MDIO MII software installation 19 On board jumper setting and Software Application 19 MDC/MDIO SMI Software 21 MDC/MDIO SMI On board jumper setting and Software Application 21 EEPROM Software Tool 22 EEPROM software On board jumper setting and Software Application 22 Window SPI Software Tool 25 Window SPI software installation 25 On board jumper setting and Software Application 25 Reference Documents 26 Bill of

Micrel Inc.
5/9/2014

KSZ8864 Evaluation Board User’s Guide

List of Figures and Tables

Figure 1 KSZ8864 Evaluation Board 5 Figure 2 KSZ8864 Evaluation Board Block Diagram 6 Table 1 Feature Setting Table 2 Reserved Jumpers 8 Table 3 EEPROM Mode Settings 8 Table 4 SPI Mode Settings 9 Table 5 LED Table 6 SCONF [1:0] pin [47,48] for SW4-MII PHY/MAC Table 7 Configure for SW4-MII 11 Table 8 Configure for SW3-MII 12 Table 9 Configure for SW4-RMII 12 Table 10 Configure for SW3-RMII 13 Table 11 MDC/MDIO Settings for MIIM 14 Table 12 MDC/MDIO Settings for SMI 14

Date 10/21/10 05/09/14

Micrel Inc.
5/9/2014

KSZ8864 Evaluation Board User’s Guide

Introduction

The KSZ8864 is Micrel Operations’ new generation integrated 4-port switch with a 64-pin small package. The KSZ8864 device consists of two PHYs and four MACs. Two of MACs support either MII or RMII interfaces for dual processor/DSP data transfer. Higher speed SPI and MDC/MDIO interfaces can fully manage the 4-port switch by the processor. The device had been designed with cost sensitive systems in mind but still offers a multitude of features such as switch management port and tag based VLAN 1/2/4-queue QoS priority a dual MII/RMII option data interfaces and CPU control interfaces of SPI, MDC/MDIO with MIIM/SMI. MIIM is the standard IEEE MII Management Interface. SMI is non-standard Serial Management Interface that can access all registers by the Management Data Input/output MDIO interface. The KSZ8864 is an excellent choice in current complex Ethernet applications with single processor or dual processors, industrial automatic, automotive, etc. fields and as a standalone 4-port switch.

The KSZ8864 evaluation board is designed to allow the user to experience first-hand the rich feature set of these existing 4-port switches of KSZ8864CNX/RMNUB. The evaluation board is highly configurable and easy to use.
• Micrel KSZ8864 Integrated 4-port 10/100 Managed Ethernet Switch
• 2 RJ-45 Jacks for Ethernet LAN with Corresponding Isolation Magnetics.
• Auto MDI/MDIX on all Ports.
• 1 PHY mode and 1 MAC mode 40-pin male/female connectors are for the port 3 Switch

SW3-MII/RMII Interfaces.
• 1 PHY mode and 1 MAC mode 40-pin male/female connectors are for the port 4 Switch

SW4-MII/RMII Interfaces.
• 1 USB Port Interface Configurable to emulate interfaces of EEPROM, SPI interface,

MDC/MDIO with SMI Interface and access all MIIM registers.
• On Board EEPROM
• 2 LEDs Per Port to Indicate the Status and Activity
• 5VDC, 2.5A Universal Power Supply

Evaluation Kit Contents
package in the Design Kit of the KSZ8864 Ethernet switch product on Micrel website. Contact your Micrel FAE for the latest schematic .
• The USB cable is not included.

Micrel Inc.
5/9/2014

KSZ8864 Evaluation Board User’s Guide

Hardware Description

The KSZ8864 evaluation board is in a compact form factor and can sit on a bench near a computer/laptop. There are three options for configuration strap in mode EEPROM mode and SPI mode. Strap in mode configuration is easily done with on board jumper options. EEPROM mode and SPI mode are accomplished through a built in USB port interface. Using Micrel EEPROM software and your PC, you can reprogram the EEPROM on board by the USB port. Or using Micrel SPI software and your PC, you can access the KSZ8864’s full feature set registers by the USB to SPI interface. The board also features the MII connectors for the Switch MII/RMII interface on port 3 and port These are to facilitate connections from the switch to an external MAC or PHY with MII/RMII interface.

The KSZ8864 evaluation board is easy to use. There are programmable LED indicators for link and activity on all ports and a power LED. A manual reset button allows the user to reset the board without removing the power plug. A standard 5VDC power supply is included so that the user can supply power from any 110-240 Volt AC wall or bench socket, and the power also can be provided by USB port when close pin 2-3 of the JP47 jumper.

Micrel Inc.

Figure 1 KSZ8864 Evaluation Board

Page 5
5/9/2014

KSZ8864 Evaluation Board User’s Guide
5 VDC Jack

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived KSZ8864RMNUB-EVAL Datasheet file may be downloaded here without warranties.

Datasheet ID: KSZ8864RMNUB-EVAL 647883