B10011S-MFPG3Y

B10011S-MFPG3Y Datasheet


B10011S

Part Datasheet
B10011S-MFPG3Y B10011S-MFPG3Y B10011S-MFPG3Y (pdf)
Related Parts Information
B10011S-MFPG3 B10011S-MFPG3 B10011S-MFPG3
B10011S-MFPG3Y74 B10011S-MFPG3Y74 B10011S-MFPG3Y74
B10011S-MFPG1Y B10011S-MFPG1Y B10011S-MFPG1Y
B10011S-MFPG1Y74 B10011S-MFPG1Y74 B10011S-MFPG1Y74
PDF Datasheet Preview
• Capability of Single-wire Operation
• Hardware Fault Recognition
• Inputs with High Common-mode and Differential-mode Interference Rejection Above
100 VPP due to External Filters at the Receiver Input
• Immunity Against Electromagnetic Interference
• Immunity Against Ground-voltage Offsets < 6V
• Ruggedized Against ESD by MIL-STD-883C, Method 3015

Systems which employ this device have the following benefits compared to solutions using discrete components:
• High Reliability
• Especially Suited for Truck and Van Applications
• Interface Between Truck and Trailer
• Interface Between Dashboard and Engine

Can Transceiver IC

B10011S

The CAN driver IC B10011S is a low-speed, high-level interface for 24V 27V operation with transmission levels according to ISO WD 11992-1 point-to-point interface between trucks and trailers . It is developed for signal levels of 8V/16V and a speed of up to 250 kbits/s.

This device allows transmission, that is insensitive to electromagnetic interference. Such interferences may especially occur in truck applications where due to the length of the wires high common-mode voltages e.g., 50 can be coupled into the lines.

This device contains a fault recognition circuit that detects faults on one of the two wires, which are normally used for transmission. If a fault occurs the operation can be switched from double-wire to single-wire mode thus, allowing proper operation even if one wire is broken, has a short-cut or a high series resistance.

Figure Block Diagram
1 Select
control

Error control
16 Compa-
rators 15

Output control
14 VCC
13 12

B10011S
10 GND
2 B10011S

Pin Configuration

Figure Pinning SO16

ASEL 1 BSEL 2

ER 3 RX1 4 RX0 5 TX0 6 VDD 7 VSS 8
16 F1 15 F0 14 S+ 13 VCC 12 H' 11 L' 10 GND

Table

Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Pin Description 16-lead SOIC SO16 , Small Outline Gull - Wing

Symbol Function

ASEL Select control input

BSEL Select control input

Error signal output

Reference voltage 2.5V

Receiver output

Transmitter input

Controller supply voltage 5V

Controller supply voltage 0V

Collector of internal NPN switch

Vehicle ground 0V
Ordering Information

Extended Type Number B10011S-MFPG1Y B10011S-MFPG3Y

Package Information

B10011S

Package SO16

Remarks Pb-free, 1k, taped and reeled Pb-free, 4k, taped and reeled

Pin 1
± ± ± ±

History
4749D-AUTO-10/07
• Put datasheet in a new template
• Pb-free logo on page 1 deleted
• Table “Ordering Information” on page 11 changed
4749C-AUTO-09/05
• Put datasheet in a new template
• Pb-free logo on page 1 added
• Table “Ordering Information” on page 11 changed
4749B-AUTO-09/04
• Figure 2 “Pinning SO16” on page 2 changed

Headquarters

Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel 1 408 441-0311 Fax 1 408 487-2600

International

Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel 852 2721-9778 Fax 852 2722-1369

Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-en-Yvelines Cedex France Tel 33 1-30-60-70-00 Fax 33 1-30-60-71-11

Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel 81 3-3523-3551 Fax 81 3-3523-7581

Product Contact

Web Site

Literature Requests

Technical Support

Sales Contact

Disclaimer The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
2007 Atmel Corporation. All rights reserved. logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
More datasheets: A61-113-200P4C3 | A61-114-200P4C3 | A61-112-200P4C3 | A61-114-233P4C3 | A61-112-233P4C3 | A61-113-233P4C3 | EVAL-AD7492CBZ | B10011S-MFPG3 | B10011S-MFPG3Y74 | B10011S-MFPG1Y


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived B10011S-MFPG3Y Datasheet file may be downloaded here without warranties.

Datasheet ID: B10011S-MFPG3Y 519333