B10011S
Part | Datasheet |
---|---|
![]() |
B10011S-MFPG1Y (pdf) |
Related Parts | Information |
---|---|
![]() |
B10011S-MFPG3 |
![]() |
B10011S-MFPG3Y74 |
![]() |
B10011S-MFPG3Y |
![]() |
B10011S-MFPG1Y74 |
PDF Datasheet Preview |
---|
• Capability of Single-wire Operation • Hardware Fault Recognition • Inputs with High Common-mode and Differential-mode Interference Rejection Above 100 VPP due to External Filters at the Receiver Input • Immunity Against Electromagnetic Interference • Immunity Against Ground-voltage Offsets < 6V • Ruggedized Against ESD by MIL-STD-883C, Method 3015 Systems which employ this device have the following benefits compared to solutions using discrete components: • High Reliability • Especially Suited for Truck and Van Applications • Interface Between Truck and Trailer • Interface Between Dashboard and Engine Can Transceiver IC B10011S The CAN driver IC B10011S is a low-speed, high-level interface for 24V 27V operation with transmission levels according to ISO WD 11992-1 point-to-point interface between trucks and trailers . It is developed for signal levels of 8V/16V and a speed of up to 250 kbits/s. This device allows transmission, that is insensitive to electromagnetic interference. Such interferences may especially occur in truck applications where due to the length of the wires high common-mode voltages e.g., 50 can be coupled into the lines. This device contains a fault recognition circuit that detects faults on one of the two wires, which are normally used for transmission. If a fault occurs the operation can be switched from double-wire to single-wire mode thus, allowing proper operation even if one wire is broken, has a short-cut or a high series resistance. Figure Block Diagram 1 Select control Error control 16 Compa- rators 15 Output control 14 VCC 13 12 B10011S 10 GND 2 B10011S Pin Configuration Figure Pinning SO16 ASEL 1 BSEL 2 ER 3 RX1 4 RX0 5 TX0 6 VDD 7 VSS 8 16 F1 15 F0 14 S+ 13 VCC 12 H' 11 L' 10 GND Table Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Pin Description 16-lead SOIC SO16 , Small Outline Gull - Wing Symbol Function ASEL Select control input BSEL Select control input Error signal output Reference voltage 2.5V Receiver output Transmitter input Controller supply voltage 5V Controller supply voltage 0V Collector of internal NPN switch Vehicle ground 0V Ordering Information Extended Type Number B10011S-MFPG1Y B10011S-MFPG3Y Package Information B10011S Package SO16 Remarks Pb-free, 1k, taped and reeled Pb-free, 4k, taped and reeled Pin 1 ± ± ± ± History 4749D-AUTO-10/07 • Put datasheet in a new template • Pb-free logo on page 1 deleted • Table “Ordering Information” on page 11 changed 4749C-AUTO-09/05 • Put datasheet in a new template • Pb-free logo on page 1 added • Table “Ordering Information” on page 11 changed 4749B-AUTO-09/04 • Figure 2 “Pinning SO16” on page 2 changed Headquarters Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel 1 408 441-0311 Fax 1 408 487-2600 International Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel 852 2721-9778 Fax 852 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-en-Yvelines Cedex France Tel 33 1-30-60-70-00 Fax 33 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel 81 3-3523-3551 Fax 81 3-3523-7581 Product Contact Web Site Literature Requests Technical Support Sales Contact Disclaimer The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. 2007 Atmel Corporation. All rights reserved. logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. |
More datasheets: AK670/3-2-R | A61-113-200P4C3 | A61-114-200P4C3 | A61-112-200P4C3 | A61-114-233P4C3 | A61-112-233P4C3 | A61-113-233P4C3 | EVAL-AD7492CBZ | B10011S-MFPG3 | B10011S-MFPG3Y74 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived B10011S-MFPG1Y Datasheet file may be downloaded here without warranties.