AT91CAP7A-STK

AT91CAP7A-STK Datasheet

The AT91CAP7A-STK Starter Kit is built on a single PCB, including:

Part	Datasheet
AT91CAP7A-STK	AT91CAP7A-STK (pdf)

PDF Datasheet Preview
CAPTM CUSTOMIZABLE MICROCONTROLLERS Starter Kit for CAP Customizable Microcontroller The CAP Starter Kit is the ideal vehicle for low-cost, no-risk evaluation of the customization capabilities of Atmel’s CAP microcontroller. It is intended to familiarize the user with the CAP concept and architecture, and is an ideal vehicle for students of electronic engineering to consolidate their knowledge of systemon-chip design, both hardware and software. CAP comprises a microcontroller-based system-on-chip with processor, memories, peripherals and standard interfaces, together with a Metal Programmable MP Block for application-specific functions. The CAP Starter Kit facilitates the mapping of application-specific IP blocks into its FPGA that emulates the functionality of the CAP MP Block, while at the same time providing a development platform for software for the ARM processor. This enables the hardware and software of simple applications, or modules of more complex applications, to be tested at close to operational speed. CAP Starter Kit Board The AT91CAP7A-STK Starter Kit is built on a single PCB, including: Microcontroller System-On-Chip n 64M Bytes SDRAM Memory, 3.3V n 256M Bytes NAND Flash, 3.3V n II EP2C8F256C7N 256BGA n Altera Configuration PROM -EPCS4SI8N n Extension Connector x3 for I/O Access n inch TFT Color LCD n Serial Ports One Connected to the CAP7 Debug Unit n One USB Full Speed Device Port n Mini Joy Stick n Four Analog Inputs n Light Sensor n Temperature Sensor n Voltage Potentiometer n Voltage Regulators 1.2V, 2.5V and 3.3V n Points for CAP7 Power Measurements n Eight LED’s Four Push Buttons n JTAG ICE Connector CAP7 n JTAG ISP Connector FPGA n POR Circuit for FPGA n POR Circuit for CAP7 n 50 MHz OSC Starter Kit for CAP Customizable Microcontroller CAP Starter Kit Development The CAP Starter Kit is supplied with an essential set of development tools in order to get started immediately. These include: n for downloading IAR KickStart version of IAR Embedded for ARM n for downloading Altera’s free 2 Web Edition tools for FPGA programming n The CAP7 Starter Kit Standalone Board n CD for documentation and software, including everything a user needs to evaluate the CAP7 products, including software development tools and FPGA development tools n board power supply with adaptors for Europe, United Kingdom, China and the United States n A set of communication cables, including cables for USB and serial ports SDRAM JT AG Reset OSC XTALs EBI NAND Flash USB Port ADC Ports RS232 Port RS232 Port DBGU ADC Sensors CAP7 Header 40pins PIOA MPIO FPGA Altera FPGA Cyclone II EP2C8 Header 40pins JT AG

PDF Datasheet Preview

CAPTM CUSTOMIZABLE MICROCONTROLLERS

Starter Kit for CAP Customizable Microcontroller

The CAP Starter Kit is the ideal vehicle for low-cost, no-risk evaluation of the customization capabilities of Atmel’s CAP microcontroller. It is intended to familiarize the user with the CAP concept and architecture, and is an ideal vehicle for students of electronic engineering to consolidate their knowledge of systemon-chip design, both hardware and software.

CAP comprises a microcontroller-based system-on-chip with processor, memories, peripherals and standard interfaces, together with a Metal Programmable MP Block for application-specific functions. The CAP Starter Kit facilitates the mapping of application-specific IP blocks into its FPGA that emulates the functionality of the CAP MP Block, while at the same time providing a development platform for software for the ARM processor. This enables the hardware and software of simple applications, or modules of more complex applications, to be tested at close to operational speed.

CAP Starter Kit Board

The AT91CAP7A-STK Starter Kit is built on a single PCB, including:

Microcontroller System-On-Chip
n 64M Bytes SDRAM Memory, 3.3V n 256M Bytes NAND Flash, 3.3V n II EP2C8F256C7N 256BGA n Altera Configuration PROM -EPCS4SI8N n Extension Connector x3 for I/O

Access
n inch TFT Color LCD n Serial Ports One Connected to the CAP7

Debug Unit
n One USB Full Speed Device Port n Mini Joy Stick
n Four Analog Inputs n Light Sensor n Temperature Sensor n Voltage Potentiometer n Voltage Regulators 1.2V, 2.5V and 3.3V n Points for CAP7 Power Measurements n Eight LED’s Four Push Buttons n JTAG ICE Connector CAP7 n JTAG ISP Connector FPGA n POR Circuit for FPGA n POR Circuit for CAP7 n 50 MHz OSC

Starter Kit for CAP Customizable Microcontroller

CAP Starter Kit Development

The CAP Starter Kit is supplied with an essential set of development tools in order to get started immediately. These include:
n for downloading IAR KickStart version of IAR Embedded
for ARM
n for downloading Altera’s free 2 Web Edition
tools for FPGA programming
n The CAP7 Starter Kit Standalone Board n CD for documentation and software, including everything a user needs
to evaluate the CAP7 products, including software development tools and FPGA development tools
n board power supply with adaptors for Europe, United Kingdom, China and the

United States
n A set of communication cables, including cables for USB and serial ports

SDRAM

JT AG

Reset OSC XTALs

EBI NAND Flash

USB Port ADC Ports

RS232 Port

RS232 Port

DBGU ADC

Sensors

CAP7

Header 40pins

PIOA MPIO

FPGA

Altera FPGA Cyclone II EP2C8

Header 40pins

JT AG

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT91CAP7A-STK Datasheet file may be downloaded here without warranties.

Datasheet ID: AT91CAP7A-STK 519107