AT27C040-90RI

AT27C040-90RI Datasheet


AT27C040

Part Datasheet
AT27C040-90RI AT27C040-90RI AT27C040-90RI (pdf)
Related Parts Information
AT27C040-15RI AT27C040-15RI AT27C040-15RI
AT27C040-70RI AT27C040-70RI AT27C040-70RI
AT27C040-12RI AT27C040-12RI AT27C040-12RI
AT27C040-12RC AT27C040-12RC AT27C040-12RC
AT27C040-90RC AT27C040-90RC AT27C040-90RC
AT27C040-15RC AT27C040-15RC AT27C040-15RC
AT27C040-70RC AT27C040-70RC AT27C040-70RC
PDF Datasheet Preview
AT27C040
• Fast Read Access Time - 70 ns
• Low Power CMOS Operation
100 µA max. Standby 30 mA max. Active at 5 MHz
• JEDEC Standard Packages 32-Lead 600-mil PDIP 32-Lead 450-mil SOIC SOP 32-Lead PLCC 32-Lead TSOP
• 5V ± 10% Supply
• High Reliability CMOS Technology 2000V ESD Protection 200 mA Latchup Immunity
• Rapid Programming Algorithm - 100 µs/byte typical
• CMOS and TTL Compatible Inputs and Outputs
• Integrated Product Identification Code
• Commercial and Industrial Temperature Ranges

The AT27C040 chip is a low-power, high-performance, 4,194,304-bit one-time programmable read only memory OTP EPROM organized as 512K by 8 bits. The AT27C040 requires only one 5V power supply in normal read mode operation. Any byte can be accessed in less than 70 ns, eliminating the need for speed reducing WAIT states on high-performance microprocessor systems.

Atmel's scaled CMOS technology provides low active power consumption, and fast
programming. Power consumption is typically 8 mA in active mode and less than 10
µA in standby mode.
continued

Pin Configurations

Pin Name Function

PDIP, SOIC Top View

A0 - A18 Addresses

O0 - O7 Outputs

Chip Enable

Output Enable
4-Megabit 512K x 8 OTP EPROM

AT27C040

PLCC Top View

TSOP Top View

The AT27C040 is available in a choice of industry standard JEDEC-approved one-time programmable OTP plastic PDIP, PLCC, SOIC SOP , and TSOP packages. The device features two-line control CE, OE to eliminate bus contention in high-speed systems.

Atmel's AT27C040 has additional features to ensure high quality and efficient production use. The Rapid Programming Algorithm reduces the time required to program the part and guarantees reliable programming. Programming time is typically only 100 µs/byte. The Integrated Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry standard programming equipment to select the proper programming algorithms and voltages.

Switching Considerations

Switching between active and standby conditions via the Chip Enable pin may produce transient voltage excursions. Unless accommodated by the system design, these transients may exceed data sheet limits, resulting in device non-conformance. At a minimum, a µF high frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected between the VCC and Ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a µF bulk electrolytic capacitor should be utilized, again connected between the VCC and Ground terminals. This capacitor should be positioned as close as possible to the point where the power supply is connected to the array.

AT27C040

Block Diagram

AT27C040

Operating Modes

Mode/Pin Read

CE OE

VPP X 1

Outputs DOUT

Output Disable

High Z

Standby Rapid Program 2

High Z

PGM Verify

DOUT

PGM Inhibit

Product Identification 4

Notes X can be VIL or VIH. Refer to Programming Characteristics

X A9 = VH 3 A0 = VIH or VIL A1 - A18 = VIL
Ordering Information
tACC ns 70

ICC mA

Active

Standby
Ordering Code AT27C040-70JC AT27C040-70PC AT27C040-70RC AT27C040-70TC AT27C040-70JI AT27C040-70PI AT27C040-70RI AT27C040-70TI AT27C040-90JC AT27C040-90PC AT27C040-90RC AT27C040-90TC AT27C040-90JI AT27C040-90PI AT27C040-90RI AT27C040-90TI AT27C040-12JC AT27C040-12PC AT27C040-12RC AT27C040-12TC AT27C040-12JI AT27C040-12PI AT27C040-12RI AT27C040-12TI AT27C040-15JC AT27C040-15PC AT27C040-15RC AT27C040-15TC AT27C040-15JI AT27C040-15PI AT27C040-15RI AT27C040-15TI

Package 32J 32P6 32R 32T 32J 32P6 32R 32T 32J 32P6 32R 32T 32J 32P6 32R 32T 32J 32P6 32R 32T 32J 32P6 32R 32T 32J 32P6 32R 32T 32J 32P6 32R 32T
32J 32P6 32R 32T

Package Type 32-Lead, Plastic J-Leaded Chip Carrier PLCC 32-Lead, Wide, Plastic Dual Inline Package PDIP 32-Lead, Wide, Plastic Gull Wing Small Outline SOIC 32-Lead, Plastic Thin Small Outline Package TSOP

AT27C040

Operation Range Commercial 0°C to 70°C Industrial
-40°C to 85°C Commercial 0°C to 70°C Industrial
-40°C to 85°C Commercial 0°C to 70°C Industrial
-40°C to 85°C Commercial 0°C to 70°C Industrial
-40°C to 85°C
More datasheets: CENB1040A1203N01 | CENB1040A0503F01 | CENB1040A0903F01 | 74LVTH32245GX | 74LVTH32245G | AT27C040-15RI | AT27C040-70RI | AT27C040-12RI | AT27C040-12RC | AT27C040-90RC


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT27C040-90RI Datasheet file may be downloaded here without warranties.

Datasheet ID: AT27C040-90RI 518935