AT17F16A-30JU

AT17F16A-30JU Datasheet

AT17F16A

Part	Datasheet
AT17F16A-30JU	AT17F16A-30JU (pdf)

PDF Datasheet Preview
• Programmable 16, 777, 216 x 1-bit Serial Memories Designed to Store Configuration Programs for Field Programmable Gate Arrays FPGAs • 3.3V Output Capability • 5V Tolerant I/O Pins • Program Support using the Atmel ATDH2200E System or Industry Third-party Programmers • In-System Programmable ISP via 2-wire Bus • Simple Interface to SRAM FPGAs • Compatible with Atmel AT40K and AT94K Devices, Excalibur , Cyclone and APEX Devices • Cascadable Read-back to Support Additional Configurations or Higher-density Arrays • Low-power CMOS FLASH Process • Available in 8-lead LAP and 20-lead PLCC Packages • Emulation of Atmel’s AT24CXXX Serial EEPROMs • Low-power Standby Mode • Single Device Capable of Holding 4 Bit Stream Files Allowing Simple System Reconfiguration • Fast Serial Download Speeds up to 33 MHz • Endurance 10,000 Write Cycles Typical • Green Pb/Halide-free/RoHS Compliant Packages FPGA Configuration Flash Memory AT17F16A The AT17FxxA Series of In-System Programmable Configuration PROMs Configurators provide an easy-to-use, cost-effective configuration memory for Field Programmable Gate Arrays. The AT17FxxA Series device is packaged in the 8-lead LAP and 20-lead PLCC, see Table The AT17FxxA Series Configurator uses a simple serial-access procedure to configure one or more FPGA devices. The AT17FxxA Series Configurators can be programmed with industry-standard programmers, Atmel’s ATDH2200E Programming Kit or Atmel’s ATDH2225 ISP Cable. Table AT17FxxA Series Packages Package 8-lead LAP 20-lead PLCC AT17F16A Yes Pin Configuration 8-lead LAP DATA 1 DCLK 2 RESET/OE 3 nCS 4 8 VCC 7 SER_EN 6 A2 nCASC 5 GND 20-lead PLCC 3 NC 2 DATA 1 NC 20 VCC 19 NC DCLK 4 NC 5 NC 6 PAGESEL1 7 RESET/OE 8 18 SER_EN 17 NC 16 PAGE_EN 15 READY 14 NC nCS 9 GND 10 PAGESEL0 11 A2 nCASC 12 NC 13 2 AT17F16A Block Diagram READY PAGE_EN PAGESEL0 PAGESEL1 Power-on Reset Reset Config. Page Select AT17F16A Clock/Oscillator Logic Serial Download Logic DCLK nCASC A2 Flash Memory CE/WE/OE Data Address 2-wire Serial Programming Control Logic DATA nCS RESET/OE SER_EN Device Description Ordering Code Package 1 16-Mbit AT17F16A-30CU AT17F16A-30JU 8CN4-8 LAP 20J-20 PLCC Notes For the -30JC and -30JI packages, customers may migrate to the AT17F16A-30JU. Operation Range Industrial -40° C to 85° C 8CN4 20J Package Type 8-lead 6 mm x 6 mm x mm. Leadless Array Package LAP 20-lead, Plastic J-leaded Chip Carrier PLCC 12 AT17F16A Packaging Information AT17F16A Marked Pin1 Indentifier Top View Side View mm TYP 8 Bottom View Pin1 Corner SYMBOL A A1 b D E e1 L L1 COMMON DIMENSIONS Unit of Measure = mm NOM BSC REF NOTE 1 Note: Metal Pad Dimensions. All exposed metal area shall have the following finished platings. Ni to mm Au to mm Package Drawing Contact: TITLE 8CN4, 8-lead 6 x 6 x mm Body , Lead Pitch 1.27mm, Leadless Array Package LAP 8CN4 20J PLCC PIN NO. 1 IDENTIFIER e E1 E D2/E2 B1 A2 A1 A 0.51 0.020 MAX 3X This package conforms to JEDEC reference MS-018, Variation AA. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is mm per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. Lead coplanarity is mm maximum. COMMON DIMENSIONS Unit of Measure = mm SYMBOL MIN NOM MAX NOTE Note 2 Removed -30CC and -30CI devices from ordering information. Announced last-time buy for -30JC and -30JI devices. E Feb. 2008 Removed -30JC and 30JI devices from ordering information. Headquarters Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel 1 408 441-0311 Fax 1 408 487-2600 International Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel 852 2721-9778 Fax 852 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel 33 1-30-60-70-00 Fax 33 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel 81 3-3523-3551 Fax 81 3-3523-7581 Product Contact Web Site Literature Requests Technical Support Sales Contact Disclaimer The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. 2008 Atmel Corporation. All rights reserved. logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.

PDF Datasheet Preview

• Programmable 16, 777, 216 x 1-bit Serial Memories Designed to Store Configuration Programs for Field Programmable Gate Arrays FPGAs
• 3.3V Output Capability
• 5V Tolerant I/O Pins
• Program Support using the Atmel ATDH2200E System or Industry Third-party

Programmers
• In-System Programmable ISP via 2-wire Bus
• Simple Interface to SRAM FPGAs
• Compatible with Atmel AT40K and AT94K Devices, Excalibur ,

Cyclone and APEX Devices
• Cascadable Read-back to Support Additional Configurations or Higher-density Arrays
• Low-power CMOS FLASH Process
• Available in 8-lead LAP and 20-lead PLCC Packages
• Emulation of Atmel’s AT24CXXX Serial EEPROMs
• Low-power Standby Mode
• Single Device Capable of Holding 4 Bit Stream Files Allowing Simple System

Reconfiguration
• Fast Serial Download Speeds up to 33 MHz
• Endurance 10,000 Write Cycles Typical
• Green Pb/Halide-free/RoHS Compliant Packages

FPGA Configuration Flash Memory

AT17F16A

The AT17FxxA Series of In-System Programmable Configuration PROMs Configurators provide an easy-to-use, cost-effective configuration memory for Field Programmable Gate Arrays. The AT17FxxA Series device is packaged in the 8-lead LAP and 20-lead PLCC, see Table The AT17FxxA Series Configurator uses a simple serial-access procedure to configure one or more FPGA devices.

The AT17FxxA Series Configurators can be programmed with industry-standard programmers, Atmel’s ATDH2200E Programming Kit or Atmel’s ATDH2225 ISP Cable.

Table AT17FxxA Series Packages Package 8-lead LAP 20-lead PLCC

AT17F16A Yes

Pin Configuration
8-lead LAP

DATA 1 DCLK 2 RESET/OE 3
nCS 4
8 VCC 7 SER_EN 6 A2 nCASC 5 GND
20-lead PLCC
3 NC 2 DATA 1 NC 20 VCC 19 NC

DCLK 4 NC 5 NC 6

PAGESEL1 7 RESET/OE 8
18 SER_EN 17 NC 16 PAGE_EN 15 READY 14 NC
nCS 9 GND 10 PAGESEL0 11 A2 nCASC 12

NC 13
2 AT17F16A

Block Diagram

READY

PAGE_EN PAGESEL0 PAGESEL1

Power-on Reset

Reset

Config. Page Select

AT17F16A

Clock/Oscillator Logic

Serial Download Logic

DCLK nCASC A2

Flash Memory

CE/WE/OE Data

Address
2-wire Serial Programming Control Logic

DATA
nCS RESET/OE SER_EN

Device Description
Ordering Code

Package 1
16-Mbit

AT17F16A-30CU AT17F16A-30JU
8CN4-8 LAP 20J-20 PLCC

Notes For the -30JC and -30JI packages, customers may migrate to the AT17F16A-30JU.

Operation Range

Industrial -40° C to 85° C
8CN4 20J

Package Type 8-lead 6 mm x 6 mm x mm. Leadless Array Package LAP 20-lead, Plastic J-leaded Chip Carrier PLCC
12 AT17F16A

Packaging Information

AT17F16A

Marked Pin1 Indentifier

Top View

Side View
mm TYP 8

Bottom View

Pin1 Corner

SYMBOL A A1 b D E e1 L L1

COMMON DIMENSIONS Unit of Measure = mm

NOM BSC REF

NOTE 1

Note:

Metal Pad Dimensions. All exposed metal area shall have the following finished platings.

Ni to mm Au to mm

Package Drawing Contact:

TITLE 8CN4, 8-lead 6 x 6 x mm Body , Lead Pitch 1.27mm,

Leadless Array Package LAP
8CN4
20J PLCC

PIN NO. 1 IDENTIFIER
e E1 E

D2/E2 B1

A2 A1 A
0.51 0.020 MAX 3X

This package conforms to JEDEC reference MS-018, Variation AA. Dimensions D1 and E1 do not include mold protrusion.

Allowable protrusion is mm per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. Lead coplanarity is mm maximum.

COMMON DIMENSIONS Unit of Measure = mm

SYMBOL MIN NOM MAX NOTE

Note 2
Removed -30CC and -30CI devices from ordering information. Announced last-time buy for -30JC and -30JI devices.

E Feb. 2008
Removed -30JC and 30JI devices from ordering information.

Headquarters

Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel 1 408 441-0311 Fax 1 408 487-2600

International

Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel 852 2721-9778 Fax 852 2722-1369

Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel 33 1-30-60-70-00 Fax 33 1-30-60-71-11

Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel 81 3-3523-3551 Fax 81 3-3523-7581

Product Contact

Web Site

Literature Requests

Technical Support

Sales Contact

Disclaimer The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
2008 Atmel Corporation. All rights reserved. logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT17F16A-30JU Datasheet file may be downloaded here without warranties.

Datasheet ID: AT17F16A-30JU 518862