MAX30100EVKIT#

MAX30100EVKIT# Datasheet

MAX30100

Part	Datasheet
MAX30100EVKIT#	MAX30100EVKIT# (pdf)

PDF Datasheet Preview
MAX30100 EVALUATION KIT AVAILABLE Pulse Oximeter and Heart-Rate Sensor IC for Wearable Health The MAX30100 is an integrated pulse oximetry and heartrate monitor sensor solution. It combines two LEDs, a photodetector, optimized optics, and low-noise analog signal processing to detect pulse oximetry and heart-rate signals. The MAX30100 operates from 1.8V and 3.3V power supplies and can be powered down through software with negligible standby current, permitting the power supply to remain connected at all times. ●● Wearable Devices ●● Fitness Assistant Devices ●● Medical Monitoring Devices Ordering Information appears at end of data sheet. Benefits and Features ●● Complete Pulse Oximeter and Heart-Rate Sensor Solution Simplifies Design • Integrated LEDs, Photo Sensor, and High-Performance Analog Front -End • Tiny 5.6mm x 2.8mm x 1.2mm 14-Pin Optically Enhanced System-in-Package ●● Ultra-Low-Power Operation Increases Battery Life for Wearable Devices • Programmable Sample Rate and LED Current for Power Savings • Ultra-Low Shutdown Current 0.7µA, typ ●● Advanced Functionality Improves Measurement Performance • High SNR Provides Robust Motion Artifact Resilience • Integrated Ambient Light Cancellation • High Sample Rate Capability • Fast Data Output Capability System Block Diagram COVER GLASS HbO2 Hb NO INK CONTROL SIGNAL PROCESSING MAX30100 Pulse Oximeter and Heart-Rate Sensor IC for Wearable Health Absolute Maximum Ratings VDD to +2.2V GND to +0.3V x_DRV, x_LED+ to +6.0V All Other Pins to +6.0V Output Short-Circuit Current Continuous Input Current into Any Terminal.....................±20mA Continuous Power Dissipation TA = +70°C OESIP derate 5.8mW/°C above +70°C .....................464mW Operating Temperature Range............................ -40°C to +85°C Soldering Temperature Storage Temperature Range............................. -40°C to +105°C Package Thermal Characteristics Note 1 OESIP Junction-to-Ambient Thermal Resistance Junction-to-Case Thermal Resistance Note 1 Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to Electrical Characteristics VDD = 1.8V, VIR_LED+ = VR_LED+ = 3.3V, TA = +25°C, min/max are from TA = -40°C to +85°C, unless otherwise noted. Note 2 PARAMETER POWER SUPPLY CONDITIONS MIN TYP MAX UNITS Power-Supply Voltage Guaranteed by RED and IR count tolerance LED Supply Voltage R_LED+ or IR_LED+ to PGND Supply Current Supply Current in Shutdown SENSOR CHARACTERISTICS ADC Resolution Red ADC Count Note 3 IR ADC Count Note 3 Dark Current Count DC Ambient Light Rejection Note 4 VLED+ IDD ISHDN Ordering Information PART TEMP RANGE PIN-PACKAGE MAX30100EFD+ -40°C to +85°C 14 OESIP 0.8mm pitch +Denotes a lead Pb -free/RoHS-compliant package. Chip Information PROCESS BiCMOS Maxim Integrated 26 MAX30100 Pulse Oximeter and Heart-Rate Sensor IC for Wearable Health Package Information For the latest package outline information and land patterns footprints , go to Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE 14 OESIP PACKAGE CODE F142D5+2 OUTLINE NO. 21-0880 LAND PATTERN NO. 90-0461 Maxim Integrated 27 MAX30100 Pulse Oximeter and Heart-Rate Sensor IC for Wearable Health Package Information continued For the latest package outline information and land patterns footprints , go to Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. Maxim Integrated 28 MAX30100 9/14 Initial release Pulse Oximeter and Heart-Rate Sensor IC for Wearable Health PAGES CHANGED For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values min and max limits shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. 2014 Maxim Integrated Products, Inc. 29

PDF Datasheet Preview

MAX30100

EVALUATION KIT AVAILABLE

Pulse Oximeter and Heart-Rate Sensor IC for Wearable Health

The MAX30100 is an integrated pulse oximetry and heartrate monitor sensor solution. It combines two LEDs, a photodetector, optimized optics, and low-noise analog signal processing to detect pulse oximetry and heart-rate signals. The MAX30100 operates from 1.8V and 3.3V power supplies and can be powered down through software with negligible standby current, permitting the power supply to remain connected at all times.
●● Wearable Devices ●● Fitness Assistant Devices ●● Medical Monitoring Devices
Ordering Information appears at end of data sheet.

Benefits and Features
●● Complete Pulse Oximeter and Heart-Rate Sensor Solution Simplifies Design
• Integrated LEDs, Photo Sensor, and High-Performance Analog Front -End
• Tiny 5.6mm x 2.8mm x 1.2mm 14-Pin Optically Enhanced System-in-Package
●● Ultra-Low-Power Operation Increases Battery Life for Wearable Devices
• Programmable Sample Rate and LED Current for Power Savings
• Ultra-Low Shutdown Current 0.7µA, typ
●● Advanced Functionality Improves Measurement Performance
• High SNR Provides Robust Motion Artifact Resilience
• Integrated Ambient Light Cancellation
• High Sample Rate Capability
• Fast Data Output Capability

System Block Diagram

COVER GLASS

HbO2 Hb

NO INK

CONTROL

SIGNAL PROCESSING

MAX30100

Pulse Oximeter and Heart-Rate Sensor IC for Wearable Health

Absolute Maximum Ratings

VDD to +2.2V GND to +0.3V x_DRV, x_LED+ to +6.0V All Other Pins to +6.0V Output Short-Circuit Current Continuous Input Current into Any Terminal.....................±20mA

Continuous Power Dissipation TA = +70°C OESIP derate 5.8mW/°C above +70°C .....................464mW

Operating Temperature Range............................ -40°C to +85°C Soldering Temperature Storage Temperature Range............................. -40°C to +105°C

Package Thermal Characteristics Note 1

OESIP Junction-to-Ambient Thermal Resistance Junction-to-Case Thermal Resistance

Note 1 Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to

Electrical Characteristics

VDD = 1.8V, VIR_LED+ = VR_LED+ = 3.3V, TA = +25°C, min/max are from TA = -40°C to +85°C, unless otherwise noted. Note 2

PARAMETER POWER SUPPLY

CONDITIONS

MIN TYP MAX UNITS

Power-Supply Voltage

Guaranteed by RED and IR count tolerance

LED Supply Voltage R_LED+ or IR_LED+ to PGND

Supply Current

Supply Current in Shutdown SENSOR CHARACTERISTICS ADC Resolution Red ADC Count Note 3

IR ADC Count Note 3

Dark Current Count

DC Ambient Light Rejection Note 4

VLED+ IDD

ISHDN
Ordering Information

PART

TEMP RANGE

PIN-PACKAGE

MAX30100EFD+
-40°C to +85°C
14 OESIP 0.8mm pitch
+Denotes a lead Pb -free/RoHS-compliant package.

Chip Information

PROCESS BiCMOS

Maxim Integrated 26

MAX30100

Pulse Oximeter and Heart-Rate Sensor IC for Wearable Health

Package Information

For the latest package outline information and land patterns footprints , go to Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.

PACKAGE TYPE 14 OESIP

PACKAGE CODE F142D5+2

OUTLINE NO. 21-0880

LAND PATTERN NO. 90-0461

Maxim Integrated 27

MAX30100

Pulse Oximeter and Heart-Rate Sensor IC for Wearable Health

Package Information continued

For the latest package outline information and land patterns footprints , go to Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.

Maxim Integrated 28

MAX30100
9/14 Initial release

Pulse Oximeter and Heart-Rate Sensor IC for Wearable Health

PAGES CHANGED
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at

Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values min and max limits shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.

Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. 2014 Maxim Integrated Products, Inc. 29

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MAX30100EVKIT# Datasheet file may be downloaded here without warranties.

Datasheet ID: MAX30100EVKIT# 647291