MAX20313EVKIT#

MAX20313EVKIT# Datasheet

MAX20313 Evaluation Kit

Part	Datasheet
MAX20313EVKIT#	MAX20313EVKIT# (pdf)

PDF Datasheet Preview
MAX20313 Evaluation Kit Evaluates MAX20313/MAX20314/ MAX20315/MAX20316 The MAX20313 evaluation kit EV kit is a fully assembled and tested circuit board that demonstrates the MAX20313 500mA to 6A adjustable current-limit switch device. The EV kit comes with the MAX20313EWC+ installed. The EV kit board can also be used to evaluate the MAX20314, MAX20315, and MAX20316. ●● 2.5V to 5.5V Operating Voltage Range ●● Power, Enable, and Flag LED Reading ●● Proven PCB Layout ●● Fully Assembled and Tested EV Kit Contents ●● EV kit board containing a MAX20313 Ordering Information appears at end of data sheet. Quick Start Required Equipment ●● MAX20313 EV kit ●● 5V power supply ●● Multimeter ●● Load box Procedure The EV kit is fully assembled and tested. Follow the steps below to verify board operation: 1 Connect 4.3V on IN. Verify the OUT voltage is 4.3V and LED1 is on. 2 Install shunt on JU2. OUT voltage goes down and LED3 is on. 3 Remove shunt on JU2. OUT voltage is 4.3V and LED3 is off. 4 Connect load box to OUT. Increase the load current and verify OUT voltage goes down when output current goes up to about 2.06A, and LED2 turns on. 5 Decrease load current and verify OUT voltage goes back to 4.3V and LED2 turns off. MAX20313 Evaluation Kit Evaluates MAX20313/MAX20314/ MAX20315/MAX20316 Detailed Description The MAX20313 EV kit is a fully assembled and tested circuit board demonstrating the MAX20313 500mA to 6A adjustable current limit switch device in a 12-bump waferlevel package WLP . LED Indicator The EV kit features LED1 to indicate power on VIN. LED2 indicates FLAG is asserted. LED3 indicates the device is disabled. VIN Power VIN can be powered from J1, IN, OUT, or test point TP7. Use jumper JU1 to connect VIN to IN or OUT. Use jumper JU3 to connect VIN to J1 VBUS. Table 1 Enable Pin Use jumper JU2 to enable/disable the device. Table 2 Current Limit Threshold Use jumper JU4, JU5, JU6 to choose RSETI, which sets the current limit threshold. Table 4 Table JU1, JU3 Jumper Setting JUMPER JU1 JU3 Default position. SHUNT POSITION 1-2-3 Installed Not installed* DESCRIPTION VIN is connected to VOUT VIN is connected to VIN is connected to J1 VBUS VIN is not connected to J1 VBUS Table JU2 Jumper Setting JUMPER JU2 Default position. SHUNT POSITION Installed Not installed DESCRIPTION EN is low MAX20313 is disabled, LED3 is on EN is high MAX20313 is enabled, LED3 is off Table Switch Truth Table MAX20313 MAX20314 EN 0 1 MAX20315 MAX20316 Ordering Information PART MAX20313EVKIT# #Denotes RoHS compliant. TYPE EV Kit MAX20313 EV Bill of Materials ITEM REF_DES 1 C1, C2, C5 DNI/DNP QTY MFG PART # 3 C1608X7R1V105K080AC TDK MANUFACTURER 2 C6, C7 GRM188R70J105KA01 CL10B105KQ8NNNC MURATA/SAMSUNG ELECTRONICS 3 J1 4 JU1 5 JU2-JU6 6 LED1 1 ZX62D-B-5P8 1 PEC03SAAN 5 PEC02SAAN 1 LTST-C150KGKT HIROSE ELECTRIC CO LTD. SULLINS LITE-ON ELECTRONICS INC. 7 LED2 1 LTST-C150KRKT LITE-ON ELECTRONICS INC. 8 LED3 9 R1, R2, R12 10 R3, R5, R8 11 R4 12 R6 13 R7 14 R9 15 R10, R11, R13 1 LTST-C150KSKT LITE-ON ELECTRONICS INC. 3 CRCW0805680RFK VISHAY DALE CRCW08051K00FK; ERJ-6ENF1001V MCR10EZHF1001; VISHAY DALE PANASONIC ROHM YAGEO RC0805FR-071KL 1 CRCW08052K00FK VISHAY DALE 1 CRCW0805665RFK VISHAY DALE For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. 2016 Maxim Integrated Products, Inc. 7

PDF Datasheet Preview

MAX20313 Evaluation Kit

Evaluates MAX20313/MAX20314/ MAX20315/MAX20316

The MAX20313 evaluation kit EV kit is a fully assembled and tested circuit board that demonstrates the MAX20313 500mA to 6A adjustable current-limit switch device. The EV kit comes with the MAX20313EWC+ installed. The EV kit board can also be used to evaluate the MAX20314, MAX20315, and MAX20316.
●● 2.5V to 5.5V Operating Voltage Range ●● Power, Enable, and Flag LED Reading ●● Proven PCB Layout ●● Fully Assembled and Tested

EV Kit Contents
●● EV kit board containing a MAX20313
Ordering Information appears at end of data sheet.

Quick Start

Required Equipment
●● MAX20313 EV kit
●● 5V power supply
●● Multimeter
●● Load box

Procedure

The EV kit is fully assembled and tested. Follow the steps below to verify board operation:
1 Connect 4.3V on IN. Verify the OUT voltage is 4.3V and LED1 is on.
2 Install shunt on JU2. OUT voltage goes down and LED3 is on.
3 Remove shunt on JU2. OUT voltage is 4.3V and LED3 is off.
4 Connect load box to OUT. Increase the load current and verify OUT voltage goes down when output current goes up to about 2.06A, and LED2 turns on.
5 Decrease load current and verify OUT voltage goes back to 4.3V and LED2 turns off.

MAX20313 Evaluation Kit

Evaluates MAX20313/MAX20314/ MAX20315/MAX20316

Detailed Description

The MAX20313 EV kit is a fully assembled and tested circuit board demonstrating the MAX20313 500mA to 6A adjustable current limit switch device in a 12-bump waferlevel package WLP .

LED Indicator

The EV kit features LED1 to indicate power on VIN. LED2 indicates FLAG is asserted. LED3 indicates the device is disabled.

VIN Power

VIN can be powered from J1, IN, OUT, or test point TP7. Use jumper JU1 to connect VIN to IN or OUT. Use jumper JU3 to connect VIN to J1 VBUS. Table 1

Enable Pin

Use jumper JU2 to enable/disable the device. Table 2

Current Limit Threshold Use jumper JU4, JU5, JU6 to choose RSETI, which sets the current limit threshold. Table 4

Table JU1, JU3 Jumper Setting

JUMPER JU1

JU3 *Default position.

SHUNT POSITION 1-2-3*

Installed Not installed*

DESCRIPTION VIN is connected to VOUT VIN is connected to VIN is connected to J1 VBUS VIN is not connected to J1 VBUS

Table JU2 Jumper Setting

JUMPER JU2
*Default position.

SHUNT POSITION Installed

Not installed*

DESCRIPTION EN is low MAX20313 is disabled, LED3 is on EN is high MAX20313 is enabled, LED3 is off

Table Switch Truth Table

MAX20313 MAX20314

EN 0 1

MAX20315 MAX20316
Ordering Information

PART MAX20313EVKIT# #Denotes RoHS compliant.

TYPE EV Kit

MAX20313 EV Bill of Materials

ITEM

REF_DES
1 C1, C2, C5

DNI/DNP QTY

MFG PART #
3 C1608X7R1V105K080AC TDK

MANUFACTURER
2 C6, C7

GRM188R70J105KA01 CL10B105KQ8NNNC

MURATA/SAMSUNG ELECTRONICS
3 J1 4 JU1 5 JU2-JU6
6 LED1
1 ZX62D-B-5P8
1 PEC03SAAN
5 PEC02SAAN
1 LTST-C150KGKT

HIROSE ELECTRIC CO LTD. SULLINS

LITE-ON ELECTRONICS INC.
7 LED2
1 LTST-C150KRKT

LITE-ON ELECTRONICS INC.
8 LED3 9 R1, R2, R12
10 R3, R5, R8
11 R4 12 R6 13 R7 14 R9
15 R10, R11, R13
1 LTST-C150KSKT

LITE-ON ELECTRONICS INC.
3 CRCW0805680RFK

VISHAY DALE

CRCW08051K00FK;

ERJ-6ENF1001V MCR10EZHF1001;

VISHAY DALE PANASONIC ROHM YAGEO

RC0805FR-071KL
1 CRCW08052K00FK

VISHAY DALE
1 CRCW0805665RFK

VISHAY DALE
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at

Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
2016 Maxim Integrated Products, Inc. 7

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MAX20313EVKIT# Datasheet file may be downloaded here without warranties.

Datasheet ID: MAX20313EVKIT# 647271