MX25U1635FM2I-10G

MX25U1635FM2I-10G Datasheet

MX25U1635F

Part	Datasheet
MX25U1635FM2I-10G	MX25U1635FM2I-10G (pdf)

PDF Datasheet Preview
MX25U1635F MX25U1635F DATASHEET P/N PM1901 MX25U1635F Contents 4 GENERAL 6 Table Additional Feature PIN CONFIGURATIONS 8 PIN 8 BLOCK 9 DATA 10 Table Protected Area 11 Table 4K-bit Secured OTP Memory 13 Table Memory DEVICE 14 Quad Peripheral Interface QPI Read 16 COMMAND 17 Table Command Write Enable 21 Write Disable 22 Read Identification 23 Release from Deep Power-down RDP , Read Electronic Signature 24 Read Electronic Manufacturer ID & Device ID 26 QPI ID Read 27 Table ID Definitions Read Status Register 28 Write Status Register 32 Table Protection Read Data Bytes 36 Read Data Bytes at Higher Speed 37 2 x I/O Read Mode 39 4 x I/O Read Mode 40 Burst 43 Performance Enhance 44 Performance Enhance Mode 47 Sector Erase 48 Block Erase 49 Block Erase 50 Chip Erase 51 Page Program 52 4 x I/O Page Program 54 Deep Power-down 55 Enter Secured OTP 56 Exit Secured OTP 56 Read Security Register 56 P/N PM1901 MX25U1635F Table Security Register Write Security Register 57 Write Protection Selection 58 Single Block Lock/Unlock Protection 61 Read Block Lock Status 63 Gang Block Lock/Unlock 63 Program/ Erase Suspend/ 64 Erase 64 Program 64 66 No Operation 66 Software Reset-Enable RSTEN and Reset 66 Read SFDP Mode 68 Table Signature and Parameter Identification Data Values Table Parameter Table 0 JEDEC Flash Parameter Table Parameter Table 1 Macronix Flash Parameter 74 Table Reset POWER-ON 75 ELECTRICAL 76 Table ABSOLUTE MAXIMUM Table CAPACITANCE TA = 25°C, f = Table DC Table AC OPERATING 81 Table Power-Up Timing and VWI INITIAL DELIVERY 83 ERASE AND PROGRAMMING 84 LATCH-UP 84 ORDERING 85 PART NAME 86 PACKAGE 87 P/N PM1901 ADVANCED INFORMATION MX25U1635F 1.8V 16M-BIT [x 1/x 2/x 4] CMOS SERIAL MULTI I/O FLASH MEMORY GENERAL • Serial Peripheral Interface compatible -- Mode 0 and Mode 3 • 16,777,216 x 1 bit structure or 8,388,608 x 2 bits two I/O read mode structure or 4,194,304 x 4 bits four I/O read mode structure • Equal Sectors with 4K byte each, or Equal Blocks with 32K byte each or Equal Blocks with 64K byte each - Any Block can be erased individually • Single Power Supply Operation - to volt for read, erase, and program operations • Latch-up protected to 100mA from -1V to Vcc +1V • Low Vcc write inhibit is from 1.0V to 1.4V PERFORMANCE • High Performance - Fast read for SPI mode - 1 I/O 104MHz with 8 dummy cycles - 2 I/O 84MHz with 4 dummy cycles, equivalent to 168MHz - 4 I/O 104MHz with 2+4 dummy cycles, equivalent to 416MHz - Fast read for QPI mode - 4 I/O 84MHz with 2+2 dummy cycles, equivalent to 336MHz - 4 I/O 104MHz with 2+4 dummy cycles, equivalent to 416MHz - Fast program time 1.2ms typ. and 3ms max. /page 256-byte per page - Byte program time 12us typical - 8/16/32/64 byte Wrap-Around Burst Read Mode - Fast erase time 60ms typ. /sector 4K-byte per sector 250ms typ. /block 32K-byte per block , 500ms typ. / block 64K-byte per block • Low Power Consumption - Low active read current 20mA typ. at 104MHz, 15mA typ. at 84MHz - Low active erase/programming current 20mA typ. - Standby current 30uA typ. • Deep Power Down 5uA typ. • Typical 100,000 erase/program cycles • 10 years data retention SOFTWARE FEATURES • Input Data Format - 1-byte Command code • Advanced Security Features - Block lock protection The BP0-BP3 status bit defines the size of the area to be software protection against program and erase instructions - Additional 4k-bit secured OTP for unique identifier • Auto Erase and Auto Program Algorithm - Automatically erases and verifies data at selected sector or block - Automatically programs and verifies data at selected page by an internal algorithm that automatically times the program pulse widths Any page to be programed should have page in the erased state first P/N PM1901 MX25U1635F • Status Register Feature • Command Reset • Program/Erase Suspend • Electronic Identification - JEDEC 1-byte manufacturer ID and 2-byte device ID - RES command for 1-byte Device ID - REMS command for 1-byte manufacturer ID and 1-byte device ID • Support Serial Flash Discoverable Parameters SFDP mode HARDWARE FEATURES • SCLK Input - Serial clock input • SI/SIO0 - Serial Data Input or Serial Data Input/Output for 2 x I/O read mode and 4 x I/O read mode • SO/SIO1 - Serial Data Output or Serial Data Input/Output for 2 x I/O read mode and 4 x I/O read mode • WP#/SIO2 - Hardware write protection or serial data Input/Output for 4 x I/O read mode • RESET#/SIO3 - Hardware Reset pin or Serial input & Output for 4 x I/O read mode • PACKAGE - 8-pin SOP 200mil - 8-land WSON 6mm x 5mm - 8-land USON 4mm x 4mm - All devices are RoHS Compliant P/N PM1901 MX25U1635F MX25U1635F is a 16,777,216 bit serial Flash memory, which is configured as 2,097,152 x 8 internally. When it is in two or four I/O read mode, the structure becomes 8,388,608 bits x 2 or 4,194,304 bits x MX25U1635F feature a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus while it is in single I/O mode. The three bus signals are a clock input SCLK , a serial data input SI , and a serial data output SO . Serial access to the device is enabled by CS# input. When it is in two I/O read mode, the SI pin and SO pin become SIO0 pin and SIO1 pin for address/dummy bits input and data output. When it is in four I/O read mode, the SI pin, SO pin and WP# pin become SIO0 pin, SIO1 pin, SIO2 pin and SIO3 pin for address/dummy bits input and data output. The MX25U1635F Serial Multi I/O provides sequential read operation on the whole chip. After program/erase command is issued, auto program/erase algorithms which program/erase and verify the specified page or sector/block locations will be executed. Program command is executed on byte basis, or page 256 bytes basis, or word basis for erase command is executed on 4K-byte sector, 32K-byte block, or 64K-byte block, or whole chip basis. To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read command can be issued to detect completion status of a program or erase operation via the WIP bit. Advanced security features enhance the protection and security functions, please see security features section for more details. When the device is not in operation and CS# is high, it is put in standby mode and draws less than 30uA DC current. The MX25U1635F utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after 100,000 program and erase cycles. P/N PM1901 ORDERING INFORMATION PART NO. MX25U1635FM2I-10G CLOCK MHz MX25U1635FZNI-10G MX25U1635FZUI-10G TEMPERATURE -40°C~85°C -40°C~85°C -40°C~85°C MX25U1635F PACKAGE 8-SOP 200mil 8-WSON 6mmx5mm 8-USON 4mmx4mm Remark RoHS Compliant RoHS Compliant RoHS Compliant P/N PM1901 MX25U1635F PART NAME DESCRIPTION MX 25 U 1635F ZN I OPTION G RoHS Compliant SPEED 10 104MHz TEMPERATURE RANGE I Industrial -40°C to 85°C PACKAGE M2 8-SOP 200mil ZN 8-WSON 6mmx5mm ZU 8-USON 4mmx4mm DENSITY & MODE 1635F 16Mb TYPE U 1.8V DEVICE 25 Serial Flash P/N PM1901 PACKAGE INFORMATION MX25U1635F P/N PM1901 MX25U1635F P/N PM1901 MX25U1635F P/N PM1901 MX25U1635F Except for customized products which has been expressly identified in the applicable agreement, Macronix's products are designed, developed, and/or manufactured for ordinary business, industrial, personal, and/or household applications only, and not for use in any applications which may, directly or indirectly, cause death, personal injury, or severe property damages. In the event Macronix products are used in contradicted to their target usage above, the buyer shall take any and all actions to ensure said Macronix's product qualified for its actual use in accordance with the applicable laws and regulations and Macronix as well as it’s suppliers and/or distributors shall be released from any and all liability arisen therefrom. Copyright Macronix International Co., Ltd. All rights reserved, including the trademarks and tradename thereof, such as Macronix, MXIC, MXIC Logo, MX Logo, Integrated Solutions Provider, NBit, Nbit, NBiit, Macronix NBit, eLiteFlash, HybridNVM, HybridFlash, XtraROM, Phines, KH Logo, BE-SONOS, KSMC, Kingtech, MXSMIO, Macronix vEE, Macronix MAP, Rich io, Rich Book, Rich TV, and FitCAM. The names and brands of third party referred thereto if any are for identification purposes only. For the contact and order information, please visit Macronix’s Web site at: MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice. 90

PDF Datasheet Preview

MX25U1635F

MX25U1635F DATASHEET

P/N PM1901

MX25U1635F

Contents
4 GENERAL 6

Table Additional Feature PIN CONFIGURATIONS 8 PIN 8 BLOCK 9 DATA 10

Table Protected Area 11 Table 4K-bit Secured OTP Memory 13 Table Memory DEVICE 14 Quad Peripheral Interface QPI Read 16 COMMAND 17 Table Command Write Enable 21 Write Disable 22 Read Identification 23 Release from Deep Power-down RDP , Read Electronic Signature 24 Read Electronic Manufacturer ID & Device ID 26 QPI ID Read 27 Table ID Definitions Read Status Register 28 Write Status Register 32 Table Protection Read Data Bytes 36 Read Data Bytes at Higher Speed 37 2 x I/O Read Mode 39 4 x I/O Read Mode 40 Burst 43 Performance Enhance 44 Performance Enhance Mode 47 Sector Erase 48 Block Erase 49 Block Erase 50 Chip Erase 51 Page Program 52 4 x I/O Page Program 54 Deep Power-down 55 Enter Secured OTP 56 Exit Secured OTP 56 Read Security Register 56

P/N PM1901

MX25U1635F

Table Security Register Write Security Register 57 Write Protection Selection 58 Single Block Lock/Unlock Protection 61 Read Block Lock Status 63 Gang Block Lock/Unlock 63 Program/ Erase Suspend/ 64 Erase 64 Program 64 66 No Operation 66 Software Reset-Enable RSTEN and Reset 66 Read SFDP Mode 68
Table Signature and Parameter Identification Data Values Table Parameter Table 0 JEDEC Flash Parameter Table Parameter Table 1 Macronix Flash Parameter 74 Table Reset POWER-ON 75 ELECTRICAL 76 Table ABSOLUTE MAXIMUM Table CAPACITANCE TA = 25°C, f = Table DC Table AC OPERATING 81 Table Power-Up Timing and VWI INITIAL DELIVERY 83 ERASE AND PROGRAMMING 84 LATCH-UP 84 ORDERING 85 PART NAME 86 PACKAGE 87

P/N PM1901

ADVANCED INFORMATION MX25U1635F
1.8V 16M-BIT [x 1/x 2/x 4] CMOS SERIAL MULTI I/O FLASH MEMORY

GENERAL
• Serial Peripheral Interface compatible -- Mode 0 and Mode 3
• 16,777,216 x 1 bit structure or 8,388,608 x 2 bits two I/O read mode structure or 4,194,304 x 4 bits four I/O
read mode structure
• Equal Sectors with 4K byte each, or Equal Blocks with 32K byte each or Equal Blocks with 64K byte each
- Any Block can be erased individually
• Single Power Supply Operation
- to volt for read, erase, and program operations
• Latch-up protected to 100mA from -1V to Vcc +1V
• Low Vcc write inhibit is from 1.0V to 1.4V

PERFORMANCE
• High Performance
- Fast read for SPI mode - 1 I/O 104MHz with 8 dummy cycles - 2 I/O 84MHz with 4 dummy cycles, equivalent to 168MHz - 4 I/O 104MHz with 2+4 dummy cycles, equivalent to 416MHz
- Fast read for QPI mode - 4 I/O 84MHz with 2+2 dummy cycles, equivalent to 336MHz - 4 I/O 104MHz with 2+4 dummy cycles, equivalent to 416MHz
- Fast program time 1.2ms typ. and 3ms max. /page 256-byte per page - Byte program time 12us typical - 8/16/32/64 byte Wrap-Around Burst Read Mode - Fast erase time 60ms typ. /sector 4K-byte per sector 250ms typ. /block 32K-byte per block , 500ms typ. / block 64K-byte per block
• Low Power Consumption - Low active read current 20mA typ. at 104MHz, 15mA typ. at 84MHz - Low active erase/programming current 20mA typ. - Standby current 30uA typ.
• Deep Power Down 5uA typ.
• Typical 100,000 erase/program cycles
• 10 years data retention

SOFTWARE FEATURES
• Input Data Format
- 1-byte Command code
• Advanced Security Features
- Block lock protection The BP0-BP3 status bit defines the size of the area to be software protection against program and erase instructions - Additional 4k-bit secured OTP for unique identifier
• Auto Erase and Auto Program Algorithm
- Automatically erases and verifies data at selected sector or block - Automatically programs and verifies data at selected page by an internal algorithm that automatically times the
program pulse widths Any page to be programed should have page in the erased state first

P/N PM1901

MX25U1635F
• Status Register Feature
• Command Reset
• Program/Erase Suspend
• Electronic Identification
- JEDEC 1-byte manufacturer ID and 2-byte device ID
- RES command for 1-byte Device ID - REMS command for 1-byte manufacturer ID and 1-byte device ID
• Support Serial Flash Discoverable Parameters SFDP mode

HARDWARE FEATURES
• SCLK Input
- Serial clock input
• SI/SIO0
- Serial Data Input or Serial Data Input/Output for 2 x I/O read mode and 4 x I/O read mode
• SO/SIO1
- Serial Data Output or Serial Data Input/Output for 2 x I/O read mode and 4 x I/O read mode
• WP#/SIO2
- Hardware write protection or serial data Input/Output for 4 x I/O read mode
• RESET#/SIO3
- Hardware Reset pin or Serial input & Output for 4 x I/O read mode
• PACKAGE
- 8-pin SOP 200mil - 8-land WSON 6mm x 5mm
- 8-land USON 4mm x 4mm - All devices are RoHS Compliant

P/N PM1901

MX25U1635F

MX25U1635F is a 16,777,216 bit serial Flash memory, which is configured as 2,097,152 x 8 internally. When it is in two or four I/O read mode, the structure becomes 8,388,608 bits x 2 or 4,194,304 bits x MX25U1635F feature a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus while it is in single I/O mode. The three bus signals are a clock input SCLK , a serial data input SI , and a serial data output SO . Serial access to the device is enabled by CS# input.

When it is in two I/O read mode, the SI pin and SO pin become SIO0 pin and SIO1 pin for address/dummy bits input and data output. When it is in four I/O read mode, the SI pin, SO pin and WP# pin become SIO0 pin, SIO1 pin, SIO2 pin and SIO3 pin for address/dummy bits input and data output.

The MX25U1635F Serial Multi I/O provides sequential read operation on the whole chip.

After program/erase command is issued, auto program/erase algorithms which program/erase and verify the specified page or sector/block locations will be executed. Program command is executed on byte basis, or page 256 bytes basis, or word basis for erase command is executed on 4K-byte sector, 32K-byte block, or 64K-byte block, or whole chip basis.

To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read command can be issued to detect completion status of a program or erase operation via the WIP bit.

Advanced security features enhance the protection and security functions, please see security features section for more details.

When the device is not in operation and CS# is high, it is put in standby mode and draws less than 30uA DC current.

The MX25U1635F utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after 100,000 program and erase cycles.

P/N PM1901
ORDERING INFORMATION

PART NO. MX25U1635FM2I-10G

CLOCK MHz

MX25U1635FZNI-10G

MX25U1635FZUI-10G

TEMPERATURE -40°C~85°C -40°C~85°C -40°C~85°C

MX25U1635F

PACKAGE
8-SOP 200mil 8-WSON 6mmx5mm 8-USON 4mmx4mm

Remark RoHS Compliant RoHS Compliant RoHS Compliant

P/N PM1901

MX25U1635F

PART NAME DESCRIPTION

MX 25 U 1635F ZN I

OPTION G RoHS Compliant

SPEED 10 104MHz

TEMPERATURE RANGE I Industrial -40°C to 85°C

PACKAGE M2 8-SOP 200mil ZN 8-WSON 6mmx5mm ZU 8-USON 4mmx4mm

DENSITY & MODE 1635F 16Mb

TYPE U 1.8V

DEVICE 25 Serial Flash

P/N PM1901

PACKAGE INFORMATION

MX25U1635F

P/N PM1901

MX25U1635F

P/N PM1901

MX25U1635F

P/N PM1901

MX25U1635F

Except for customized products which has been expressly identified in the applicable agreement, Macronix's products are designed, developed, and/or manufactured for ordinary business, industrial, personal, and/or household applications only, and not for use in any applications which may, directly or indirectly, cause death, personal injury, or severe property damages. In the event Macronix products are used in contradicted to their target usage above, the buyer shall take any and all actions to ensure said Macronix's product qualified for its actual use in accordance with the applicable laws and regulations and Macronix as well as it’s suppliers and/or distributors shall be released from any and all liability arisen therefrom. Copyright Macronix International Co., Ltd. All rights reserved, including the trademarks and tradename thereof, such as Macronix, MXIC, MXIC Logo, MX Logo, Integrated Solutions Provider, NBit, Nbit, NBiit, Macronix NBit, eLiteFlash, HybridNVM, HybridFlash, XtraROM, Phines, KH Logo, BE-SONOS, KSMC, Kingtech, MXSMIO, Macronix vEE, Macronix MAP, Rich io, Rich Book, Rich TV, and FitCAM. The names and brands of third party referred thereto if any are for identification purposes only. For the contact and order information, please visit Macronix’s Web site at:

MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice. 90

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MX25U1635FM2I-10G Datasheet file may be downloaded here without warranties.

Datasheet ID: MX25U1635FM2I-10G 646946