EVM-915-250-BZR

EVM-915-250-BZR Datasheet


EVM-915-250

Part Datasheet
EVM-915-250-BZR EVM-915-250-BZR EVM-915-250-BZR (pdf)
Related Parts Information
EVM-915-250-BZS EVM-915-250-BZS EVM-915-250-BZS
PDF Datasheet Preview
EVM-915-250

Data Guide

Table of Contents
1 Description 2 Ordering Information 2 Electrical Specifications 4 Pin Assignments 5 Pin Descriptions 6 PCB Footprint 7 Schematic Diagram 8 Usage Guidelines for FCC Compliance
8 Antenna Selection 8 Module Modification 8 End Product Labeling Requirements
9 Additional FCC Testing Requirements 10 FCC Statements of Modular Compliance 11 Customer FCC Warning Requirements

EVM-915-250

Data Guide Preliminary

The EVM-915-250 evaluation module
supports developments with the TRM-
915-R250 embedded radio module.

The EVM-915-250 module combines a
state-of-the art low power wireless
transceiver with a powerful multipoint-

Figure 1 EVM-915-250-FCx
to-multipoint protocol controller to form a
complete wireless communication solution. With a simple UART interface,
a 130dB link budget and very low power operation modes. The module is
excellent for Automatic Meter Reading AMR , fleet management, RFID, gas
and oil sensing, Home Automation, and many other cable replacement
applications requiring long range and long battery life.

The module can operate as a transparent wire replacement solution. It can also operate in a peer-to-peer networked mode that supports node addressing and assured delivery. The module is designed to be totally transparent. Data is validated using an internally generated CRC-16 and encoded using a proprietary Frequency Hopping Spread Spectrum algorithm. Multiple modules can operate on the same channel because of the built-in carrier-sense-multiple-access CSMA protocol.
Ordering Information
Ordering Information

Product Part No. Description

Radiotronix Part No.

TRM-915-R250 Evaluation Module, EVM-915-250-FCR Right Angle RP-SMA Connector, Wi.232FHSS-250-FCC-RA-R

FCC Approved

TRM-915-R250 Evaluation Module,

EVM-915-250-FCS Straight RP-SMA Connector,

Wi.232FHSS-250-FCC-ST-R

FCC Approved

TRM-915-R250 Evaluation Module, EVM-915-250-BZR Right Angle RP-SMA Connector, Wi.232FHSS-250B-RA-R

Brazil Anatel Approved

TRM-915-R250 Evaluation Module,

EVM-915-250-BZS Straight RP-SMA Connector,

Wi.232FHSS-250B-ST-R

Brazil Anatel Approved

TRM-915-R250 Evaluation Module, EVM-915-250-CFR Right Angle SP-SMA Connector, Wi.232FHSS-250-FCC-CFTC-RA-R

Mexico CoFeTel Approved

TRM-915-R250 Evaluation Module,

EVM-915-250-CFS Straight RP-SMA Connector,

Wi.232FHSS-250-FCC-CFTC-ST-R

Mexico CoFeTel Approved
Figure 2 Ordering Information

Electrical Specifications

Electrical Specifications Parameter Power Supply Operating Voltage Supply Current

Receive Transmit, Po = 8dBm Transmit, Po = 23.5dBm Digital Interface Output Logic Low Logic High

Designation Min. Typ. Max. Units Notes
12 VDC
25 mA 60 mA 200 mA

Preliminary Draft

Electrical Specifications Continuation

Parameter

Designation Min. Typ. Max. Units Notes

Input

Logic Low Logic High Environmental
0.7*VCC
0.3*VCC

Operating Temperature Range

Figure 3 Electrical Specifications
! Warning Linx radio frequency “RF” products may be
used to control machinery or devices remotely, including machinery or devices that can cause death, bodily injuries, and/or property damage if improperly or inadvertently triggered, particularly in industrial settings or other applications implicating life-safety concerns. No Linx Technologies product is intended for use in any application without redundancies where the safety of life or property is at risk.

The customers and users of devices and machinery controlled with RF products must understand and must use all appropriate safety procedures in connection with the devices, including without limitation, using appropriate safety procedures to prevent inadvertent triggering by the user of the device and using appropriate security codes to prevent triggering of the remote controlled machine or device by users of other remote controllers.

All RF products are susceptible to RF interface that can prevent communication.

Do not use any Linx product over the limits in this data guide. Excessive voltage or extended operation at the maximum voltage could cause product failure. Exceeding the reflow temperature profile could cause product failure which is not immediately evident.

Do not make any physical or electrical modifications to any Linx product. This will void the warranty and regulatory and UL certifications and may cause product failure which is not immediately evident.

Preliminary Draft

Pin Assignments

Figure 3 Pin Assignments

Preliminary Draft

Pin Descriptions

Pin Descriptions

Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Name Vcc RXD0 TXD0 CTS0 COMMAND N/C N/C N/C N/C N/C GND N/C N/C N/C N/C PD5-EX RSSI AD0-CMD_RSP AD1-BE

Description 4V to 12V Supply Voltage Serial Port Receive Data Serial Port Transmit Data Serial Port Clear To Send Command No Electrical Connection No Electrical Connection No Electrical Connection No Electrical Connection No Electrical Connection Analog Ground Analog Ground Analog Ground Analog Ground No Electrical Connection No Electrical Connection No Electrical Connection No Electrical Connection Exception Received Signal Strength Indicator Command Response Buffer Empty

Analog Ground

Analog Ground

Figure 4 Pin Descriptions

Preliminary Draft

PCB Footprint

Schematic Diagram

Figure 5 PCB Footprint

Preliminary Draft

Figure 6 Schematic
More datasheets: RD1-4320 | VW2X30-16IO1 | VW2X30-12IO1 | VW2X30-14IO1 | VW2X30-08IO1 | PTFA181001E V4 T500 | PTFA181001FV4XWSA1 | PTFA181001EV4R250XTMA1 | PTFA181001EV4XWSA1 | PTFA181001FV4R250FTMA1


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived EVM-915-250-BZR Datasheet file may be downloaded here without warranties.

Datasheet ID: EVM-915-250-BZR 645777