C12868_FLARE-MAXI

C12868_FLARE-MAXI Datasheet

Ordering number C12868_FLARE-MAXI

Part	Datasheet
C12868_FLARE-MAXI	C12868_FLARE-MAXI (pdf)

PDF Datasheet Preview
PRODUCT DATASHEET Flare series last update 20/9/2012 Ordering number C12868_FLARE-MAXI Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Flare Lens LUXEON M Clear + mm Rectangular PMMA Pin, glue Ready FWHM Efficiency cd/lm Gerber File 100+23 degrees 94 % Available NOTE The typical divergence will be changed by different color, chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value. Ledil Oy Salorankatu 10 24240 SALO Finland November 12th 2012 21:01 Copyright Ledil Oy - Subject to change without prior notice - Page 1/2 email FAX +358-2-733 8001 PRODUCT DATASHEET Flare series last update 20/9/2012 GENERAL INFORMATION - Product series especially designed & optimized for LUXEON M series of LEDs. - Special care taken to make light distribution as uniform as possible. - Lens material optical grade PMMA with high UV and temperature resistance 105 degrees of Celcius / 220 degrees of Fahrenheit . Allows use of high current and temperature conditions. Please find more information about used material from below: - Fastening to PCB with appropriate adhesive. By clicking link below you can find Ledil recommended glue options. NOTE 1 We advise customer to ensure the suitability and sufficiency of the bond in the end product. For example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. NOTE 2 All surfaces where glue is applied must be clean, dry and free from grease and dirt. If cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LED manufacturer -this is important as cleaning shall under no circumstances damage LEDs or other electronics components on the PCB. Further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. Ledil Oy Salorankatu 10 24240 SALO Finland November 12th 2012 21:01 Copyright Ledil Oy - Subject to change without prior notice - Page 2/2 email FAX +358-2-733 8001 Detail A Scale 2:1 Material PMMA Tolerances for dimensions 0-20mm tolerance value +-0.1mm 21-45mm tolerance value +-0.2mm 46-90mm tolerance value +-0.3mm 91-100mm tolerance value +-0.4mm 101-mm tolerance value +-0.5mm This drawing is our property. It can't be reproduced or communicated without our written agreement. Ledil Oy Salorankatu 10 FIN 24240 SALO Finland DRAWING TITLE DRAWN BY Datasheet FLARE-MAXI Lens 1 CHECKED BY DESIGNED BY SIZE DRAWING NUMBER C12868 SCALE 1:1 WEIGHT g SHEET 1/1

PDF Datasheet Preview

PRODUCT DATASHEET Flare series
last update 20/9/2012
Ordering number C12868_FLARE-MAXI

Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status

Flare Lens LUXEON M Clear + mm Rectangular PMMA Pin, glue Ready

FWHM Efficiency cd/lm Gerber File
100+23 degrees 94 % Available

NOTE The typical divergence will be changed by different color, chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value.

Ledil Oy Salorankatu 10 24240 SALO Finland

November 12th 2012 21:01 Copyright Ledil Oy - Subject to change without prior notice - Page 1/2
email FAX +358-2-733 8001

PRODUCT DATASHEET Flare series
last update 20/9/2012

GENERAL INFORMATION
- Product series especially designed & optimized for LUXEON M series of LEDs. - Special care taken to make light distribution as uniform as possible. - Lens material optical grade PMMA with high UV and temperature resistance 105 degrees of Celcius / 220 degrees of Fahrenheit . Allows use of high current and temperature conditions.

Please find more information about used material from below:
- Fastening to PCB with appropriate adhesive. By clicking link below you can find Ledil recommended glue options.

NOTE 1 We advise customer to ensure the suitability and sufficiency of the bond in the end product. For example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue.

NOTE 2 All surfaces where glue is applied must be clean, dry and free from grease and dirt. If cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LED manufacturer -this is important as cleaning shall under no circumstances damage LEDs or other electronics components on the PCB.

Further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling.

Ledil Oy Salorankatu 10 24240 SALO Finland

November 12th 2012 21:01 Copyright Ledil Oy - Subject to change without prior notice - Page 2/2
email FAX +358-2-733 8001

Detail A Scale 2:1

Material PMMA

Tolerances for dimensions 0-20mm tolerance value +-0.1mm 21-45mm tolerance value +-0.2mm 46-90mm tolerance value +-0.3mm 91-100mm tolerance value +-0.4mm 101-mm tolerance value +-0.5mm

This drawing is our property. It can't be reproduced or communicated without our written agreement.

Ledil Oy Salorankatu 10 FIN 24240 SALO Finland

DRAWING TITLE

DRAWN BY

Datasheet FLARE-MAXI Lens 1

CHECKED BY

DESIGNED BY

SIZE DRAWING NUMBER

C12868

SCALE 1:1 WEIGHT g

SHEET 1/1

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived C12868_FLARE-MAXI Datasheet file may be downloaded here without warranties.

Datasheet ID: C12868_FLARE-MAXI 645512