NCD1015-LGA

NCD1015-LGA Datasheet

NCD1015-LGA

Part	Datasheet
NCD1015-LGA	NCD1015-LGA (pdf)

PDF Datasheet Preview
INTEGRATED CIRCUITS DIVISION NCD1015-LGA HDX RFID Integrated Circuit The NCD1015-LGA is a read/write module to be used in HDX contact-less RFID devices for single transponder applications in the area of electronic animal identification, operating in the low frequency kHz range, and supporting ISO 11784/85 standards. The NCD1015-LGA contains an ASIC and 2 internal capacitors one, a resonant capacitor, and the other a storage capacitor. The ASIC contains 4 memory blocks of 33 bits each, based on field programmable, non-volatile EEPROM. Each block contains 32 data bits bit 1 bit Each of the blocks can be write-protected through an associated lock bit, which is bit 0 of the corresponding block. Blocks 1 and 2 are referred to as the 64-bit identification data page 1 which is secured by an associated 16-bit CRC. Blocks 0 and 7 contain configuration parameters, as well as the option to irreversibly lock the RFID device. The HDX transponder IC receives Write-Block requests from the reader as a pulse interval encoded, 100% amplitude modulated data signal. Return data transmission from the transponder to the reader utilizes FSK encoded modulation. This is achieved by a serial data stream controlled Frequency Shift Keying FSK of the transponder's resonant circuit oscillation with an additional on-chip modulation capacitor between the two transponder terminals HF and GND. The passive transponder uses the supplied RF signal to obtain the energy needed to send the 64-bit ID code to the reader. Ordering Information Part # NCD1015-LGA Package Contact-less RFID device supporting ISO 11784/85 standards NCD1015-LGA Block Diagram ZAP_SEL CR CL DS-NCD1015-LGA-R00A INTEGRATED CIRCUITS DIVISION NCD1015-LGA Specifications 3 Package Pinout 3 Pin Description. 3 Electrical Data 3 Operating Conditions 3 Electrical Specifications 3 Application Information 4 Functional Overview and Description 4 Power Transfer 4 Communication Signal Interface - Tag to Reader 5 Frequency 5 Transponder Data Rate and Data Coding 5 Communication Signal Interface - Reader to Tag 5 Modulation 5 Reader Data Rate and Data Coding 5 Modulation 6 Write Phase and the Programming of Data 7 Transmission Protocol 8 Data Format Definitions 8 Reader Command - Request Format 8 Transponder - Response Data Format 9 CRC-CCITT ERROR CHECKING 10 Memory 10 Memory Block 10 Page 1 - Identification Data. 10 Page 4 - Configuration Register + Management Register 10 Manufacturing Information 12 Moisture Sensitivity 12 ESD Sensitivity 12 Reflow Profile. 12 Board Wash 12 Mechanical Data. 13 Dimensions 13 R00A INTEGRATED CIRCUITS DIVISION Specifications Package Pinout ZAP_SEL Bottom View NCD1015-LGA Pin Description Pin Name VDD GND HF ZAP_SEL ZAP Voltage Supply Ground Oscillating Signal Clock for the trimming Voltage for the trimming Electrical Data Operating Conditions Parameter Operating Temperature, TA Storage temperature, TSTG Minimum Maximum Unit +70 qC +100 qC Electrical Specifications Unless otherwise specified, minimum and maximum values are guaranteed by production testing or design. Typical values are characteristic of the device at 25°C, and are the result of engineering evaluations. They are provided for informational purposes only and are not guaranteed by production testing. Parameter HF Limiter Current HF Maximum Voltage Quiescent Current Consumption Default HF Capacitor Modulation Capacitor Endurance Data Retention Conditions Minimum Typical Maximum Unit

PDF Datasheet Preview

INTEGRATED CIRCUITS DIVISION

NCD1015-LGA

HDX RFID Integrated Circuit

The NCD1015-LGA is a read/write module to be used in HDX contact-less RFID devices for single transponder applications in the area of electronic animal identification, operating in the low frequency kHz range, and supporting ISO 11784/85 standards.

The NCD1015-LGA contains an ASIC and 2 internal capacitors one, a resonant capacitor, and the other a storage capacitor. The ASIC contains 4 memory blocks of 33 bits each, based on field programmable, non-volatile EEPROM. Each block contains 32 data bits bit 1 bit Each of the blocks can be write-protected through an associated lock bit, which is bit 0 of the corresponding block. Blocks 1 and 2 are referred to as the 64-bit identification data page 1 which is secured by an associated 16-bit CRC. Blocks 0 and 7 contain configuration parameters, as well as the option to irreversibly lock the RFID device.

The HDX transponder IC receives Write-Block requests from the reader as a pulse interval encoded, 100% amplitude modulated data signal.

Return data transmission from the transponder to the reader utilizes FSK encoded modulation. This is achieved by a serial data stream controlled Frequency Shift Keying FSK of the transponder's resonant circuit oscillation with an additional on-chip modulation capacitor between the two transponder terminals HF and GND. The passive transponder uses the supplied RF signal to obtain the energy needed to send the 64-bit ID code to the reader.
Ordering Information

Part # NCD1015-LGA

Package Contact-less RFID device supporting ISO 11784/85 standards

NCD1015-LGA Block Diagram

ZAP_SEL

CR CL

DS-NCD1015-LGA-R00A

INTEGRATED CIRCUITS DIVISION

NCD1015-LGA

Specifications 3 Package Pinout 3 Pin Description. 3

Electrical Data 3 Operating Conditions 3 Electrical Specifications 3

Application Information 4

Functional Overview and Description 4 Power Transfer 4 Communication Signal Interface - Tag to Reader 5 Frequency 5 Transponder Data Rate and Data Coding 5 Communication Signal Interface - Reader to Tag 5 Modulation 5 Reader Data Rate and Data Coding 5 Modulation 6 Write Phase and the Programming of Data 7

Transmission Protocol 8 Data Format Definitions 8 Reader Command - Request Format 8 Transponder - Response Data Format 9 CRC-CCITT ERROR CHECKING 10

Memory 10 Memory Block 10 Page 1 - Identification Data. 10 Page 4 - Configuration Register + Management Register 10

Manufacturing Information 12 Moisture Sensitivity 12 ESD Sensitivity 12 Reflow Profile. 12 Board Wash 12

Mechanical Data. 13 Dimensions 13

R00A

INTEGRATED CIRCUITS DIVISION

Specifications

Package Pinout

ZAP_SEL

Bottom View

NCD1015-LGA

Pin Description

Pin Name

VDD GND HF ZAP_SEL ZAP

Voltage Supply Ground Oscillating Signal Clock for the trimming Voltage for the trimming

Electrical Data

Operating Conditions

Parameter

Operating Temperature, TA Storage temperature, TSTG

Minimum Maximum Unit
+70 qC
+100 qC

Electrical Specifications

Unless otherwise specified, minimum and maximum values are guaranteed by production testing or design. Typical values are characteristic of the device at 25°C, and are the result of engineering evaluations. They are provided for informational purposes only and are not guaranteed by production testing.

Parameter

HF Limiter Current HF Maximum Voltage Quiescent Current Consumption Default HF Capacitor Modulation Capacitor Endurance Data Retention

Conditions Minimum Typical Maximum

Unit

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived NCD1015-LGA Datasheet file may be downloaded here without warranties.

Datasheet ID: NCD1015-LGA 644429