ICS1893BY-10T

ICS1893BY-10T Datasheet

ICS1893BY-10

Part	Datasheet
ICS1893BY-10T	ICS1893BY-10T (pdf)

Related Parts	Information
1893BYI-10LF	1893BYI-10LF
1893BYI-10LFT	1893BYI-10LFT
ICS1893BYI-10T	ICS1893BYI-10T
1893BY-10LF	1893BY-10LF
ICS1893BY-10	ICS1893BY-10
1893BY-10LFT	1893BY-10LFT
ICS1893BYI-10	ICS1893BYI-10

PDF Datasheet Preview
Integrated Circuit Systems, Inc. ICS1893BY-10 Document Type Data Sheet Document Stage Release 3.3-V 10Base-T/100Base-TX Integrated PHYceiver General The ICS1893BY-10 is a low-power, physical-layer device PHY that supports the ISO/IEC 10Base-T and 100Base-TX Carrier-Sense Multiple Access/Collision Detection CSMA/CD Ethernet standards. The ICS1893BY-10 supports managed or unmanaged node, repeater, and switch applications. The ICS1893BY-10 is intended for MII, Node applications that require the Auto-MIDIX feature that automatically corrects crossover errors in plant wiring. The ICS1893BY-10 incorporates digital signal processing DSP in its Physical Medium Dependent PMD sublayer. As a result, it can transmit and receive data on unshielded twisted-pair UTP category 5 cables with attenuation in excess of 24 dB at 100 MHz. With this ICS-patented technology, the ICS1893BY-10 can virtually eliminate errors from killer packets. The ICS1893BY-10 provides a Serial Management Interface for exchanging command and status information with a Station Management STA entity. The ICS1893BY-10 Media Dependent Interface MDI can be configured to provide either half- or full-duplex operation at data rates of 10 MHz or 100 MHz. The MDI configuration can be established manually with input pins or control register settings or automatically using the Auto-Negotiation features . When the ICS1893BY-10 Auto-Negotiation sublayer is enabled, it exchanges technology capability data with its remote link partner and automatically selects the highest-performance operating mode they have in common. • Supports category 5 cables with attenuation in excess of 24 dB at 100 MHz • Fully integrated, DSP-based PMD includes: Adaptive equalization and baseline wander correction Transmit wave shaping and stream cipher scrambler MLT-3 encoder and NRZ/NRZI encoder • Low-power, 0.35-micron CMOS typically 400 mW • Power-down mode typically 21mW • Single 3.3-V power supply. • Single-chip, fully integrated PHY provides PCS, PMA, PMD, and AUTONEG sublayers of IEEE standard • 10Base-T and 100Base-TX IEEE compliant • Highly configurable design supports: Node, repeater, and switch applications Managed and unmanaged applications 10M or 100M half- and full-duplex modes Parallel detection Auto-negotiation, with Next Page capabilities Auto-MDI/MDIX crossover correction • MAC/Repeater Interface can be configured as: 10M or 100M Media Independent Interface 100M Symbol Interface bypasses the PCS 10M 7-wire Serial Interface • Clock and crystal supported • Small Footprint 64-pin Thin Quad Flat Pack TQFP • Available in Industrial Temperature and Lead-Free ICS1893BY-10 Block Diagram 10/100 MII or Alternate MAC/Repeater Interface Interface MUX PCS • Frame • CRS/COL Detection • Parallel to Serial • 4B/5B MII Serial Management Interface MII Extended Register Low-Jitter Clock Synthesizer Clock 100Base-T Physical Dimensions of ICS1893BY-10 141 Ordering 142 Copyright 2004, Integrated Circuit Systems, Inc. All rights reserved. March, 2004 ICS1893BY-10 - Release Copyright 2004, Integrated Circuit Systems, Inc. All rights reserved. March, 2004 ICS1893BY-10 Data Sheet - Release Chapter 1 Abbreviations and Acronyms Chapter 1 Abbreviations and Acronyms Table 1-1 lists and interprets the abbreviations and acronyms used throughout this data sheet. Table Abbreviations and Acronyms Abbreviation / Acronym Interpretation 4B/5B 4-Bit / 5-Bit Encoding/Decoding ANSI American National Standards Institute CMOS complimentary metal-oxide semiconductor CSMA/CD Carrier Sense Multiple Access with Collision Detection Command Override Write digital signal processing End-of-Stream Delimiter FDDI Fiber Distributed Data Interface frequency-locked loop Fast Link Pulse A ‘dead’ time on the link following a 10Base-T packet, not to be confused with idle International Electrotechnical Commission IEEE Institute of Electrical and Electronic Engineers International Standards Organization Latching High Latching Low Latching Maximum Media Access Control Max. maximum Mbps Megabits per second Chapter 11 Ordering Information Chapter 11 Ordering Information Figure ICS1893BY-10 Ordering Information "T" = Tape and Reel Part / Order Number ICS1893BY-10LF ICS1893BYI-10LF ICS1893BY-10LFT ICS1893BYI-10LFT Marking 1893BY-10LF 1893BYI-10LF 1893BY-10LF 1893BYI-10LF Package 10x10 TQFP Lead Free 10x10 TQFP Lead Free 10x10 TQFP Lead Free 10x10 TQFP Lead Free Temperature 0° C to 70° C -40° C to 85° C 0° C to 70° C -40° C to 85° C Copyright 2004, Integrated Circuit Systems, Inc. All rights reserved. March, 2004 ICS1893BY-10 - Release Chapter 11 Ordering Information Integrated Circuit Systems, Inc. Corporate Headquarters Silicon Valley Web Site: 2435 Boulevard of the Generals Norristown, PA 19403 Telephone 610-630-5300 Fax: 610-630-5399 525 Race Street San Jose, CA 95126-3448 Telephone 408-297-1201 Fax: 408-925-9460 Email: Copyright 2004, Integrated Circuit Systems, Inc. All rights reserved. March, 2004

PDF Datasheet Preview

Integrated Circuit Systems, Inc.

ICS1893BY-10

Document Type Data Sheet Document Stage Release
3.3-V 10Base-T/100Base-TX Integrated PHYceiver

General

The ICS1893BY-10 is a low-power, physical-layer device PHY that supports the ISO/IEC 10Base-T and 100Base-TX Carrier-Sense Multiple Access/Collision Detection CSMA/CD Ethernet standards. The ICS1893BY-10 supports managed or unmanaged node, repeater, and switch applications.

The ICS1893BY-10 is intended for MII, Node applications that require the Auto-MIDIX feature that automatically corrects crossover errors in plant wiring.

The ICS1893BY-10 incorporates digital signal processing DSP in its Physical Medium Dependent PMD sublayer. As a result, it can transmit and receive data on unshielded twisted-pair UTP category 5 cables with attenuation in excess of 24 dB at 100 MHz. With this ICS-patented technology, the ICS1893BY-10 can virtually eliminate errors from killer packets.

The ICS1893BY-10 provides a Serial Management Interface for exchanging command and status information with a Station Management STA entity.

The ICS1893BY-10 Media Dependent Interface MDI can be configured to provide either half- or full-duplex operation at data rates of 10 MHz or 100 MHz. The MDI configuration can be established manually with input pins or control register settings or automatically using the Auto-Negotiation features . When the ICS1893BY-10 Auto-Negotiation sublayer is enabled, it exchanges technology capability data with its remote link partner and automatically selects the highest-performance operating mode they have in common.
• Supports category 5 cables with attenuation in excess of
24 dB at 100 MHz
• Fully integrated, DSP-based PMD includes:

Adaptive equalization and baseline wander correction

Transmit wave shaping and stream cipher scrambler

MLT-3 encoder and NRZ/NRZI encoder
• Low-power, 0.35-micron CMOS typically 400 mW
• Power-down mode typically 21mW
• Single 3.3-V power supply.
• Single-chip, fully integrated PHY provides PCS, PMA,

PMD, and AUTONEG sublayers of IEEE standard
• 10Base-T and 100Base-TX IEEE compliant
• Highly configurable design supports:

Node, repeater, and switch applications

Managed and unmanaged applications 10M or 100M half- and full-duplex modes

Parallel detection

Auto-negotiation, with Next Page capabilities Auto-MDI/MDIX crossover correction
• MAC/Repeater Interface can be configured as:
10M or 100M Media Independent Interface
100M Symbol Interface bypasses the PCS
10M 7-wire Serial Interface
• Clock and crystal supported
• Small Footprint 64-pin Thin Quad Flat Pack TQFP
• Available in Industrial Temperature and Lead-Free

ICS1893BY-10 Block Diagram
10/100 MII or Alternate

MAC/Repeater Interface

Interface MUX

PCS
• Frame
• CRS/COL

Detection
• Parallel to Serial
• 4B/5B

MII Serial Management

Interface

MII Extended Register

Low-Jitter Clock

Synthesizer

Clock
100Base-T
Physical Dimensions of ICS1893BY-10 141 Ordering 142

Copyright 2004, Integrated Circuit Systems, Inc. All rights reserved.

March, 2004

ICS1893BY-10 - Release

Copyright 2004, Integrated Circuit Systems, Inc. All rights reserved.

March, 2004

ICS1893BY-10 Data Sheet - Release

Chapter 1 Abbreviations and Acronyms

Chapter 1 Abbreviations and Acronyms

Table 1-1 lists and interprets the abbreviations and acronyms used throughout this data sheet.

Table Abbreviations and Acronyms

Abbreviation / Acronym

Interpretation
4B/5B
4-Bit / 5-Bit Encoding/Decoding

ANSI

American National Standards Institute

CMOS
complimentary metal-oxide semiconductor

CSMA/CD

Carrier Sense Multiple Access with Collision Detection

Command Override Write
digital signal processing

End-of-Stream Delimiter

FDDI

Fiber Distributed Data Interface
frequency-locked loop

Fast Link Pulse

A ‘dead’ time on the link following a 10Base-T packet, not to be confused with idle

International Electrotechnical Commission

IEEE

Institute of Electrical and Electronic Engineers

International Standards Organization

Latching High

Latching Low

Latching Maximum

Media Access Control

Max.
maximum

Mbps

Megabits per second
Chapter 11 Ordering Information
Chapter 11 Ordering Information
Figure ICS1893BY-10 Ordering Information "T" = Tape and Reel

Part / Order Number ICS1893BY-10LF ICS1893BYI-10LF

ICS1893BY-10LFT ICS1893BYI-10LFT

Marking 1893BY-10LF 1893BYI-10LF 1893BY-10LF 1893BYI-10LF

Package 10x10 TQFP Lead Free 10x10 TQFP Lead Free 10x10 TQFP Lead Free 10x10 TQFP Lead Free

Temperature 0° C to 70° C -40° C to 85° C 0° C to 70° C -40° C to 85° C

Copyright 2004, Integrated Circuit Systems, Inc. All rights reserved.

March, 2004

ICS1893BY-10 - Release
Chapter 11 Ordering Information

Integrated Circuit Systems, Inc.

Corporate Headquarters Silicon Valley Web Site:
2435 Boulevard of the Generals

Norristown, PA 19403

Telephone 610-630-5300

Fax:
610-630-5399
525 Race Street

San Jose, CA 95126-3448

Telephone 408-297-1201

Fax:
408-925-9460

Email:

Copyright 2004, Integrated Circuit Systems, Inc. All rights reserved.

March, 2004

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ICS1893BY-10T Datasheet file may be downloaded here without warranties.

Datasheet ID: ICS1893BY-10T 636958