SAE800G GEG

SAE800G GEG Datasheet

SAE 800

Part	Datasheet
SAE800G GEG	SAE800G GEG (pdf)

Related Parts	Information
SAE800FKLA1	SAE800FKLA1
SAE800GXLLA1	SAE800GXLLA1
SAE800	SAE800

PDF Datasheet Preview
Programmable Single-/Dual-/Triple- Tone Gong Pb-free lead plating RoHS compliant Features q Supply voltage range V to 18 V q Few external components no electrolytic capacitor q 1 tone, 2 tones, 3 tones programmable q Loudness control q Typical standby current 1 µA q Constant current output stage no oscillation q High-efficiency power stage q Short-circuit protection q Thermal shutdown SAE 800 Bipolar IC PG-DIP-8-4 PG-DSO-8-1 Type w SAE 800 w SAE 800 G w New type Ordering Code Q67000-A8339 Q67000-A8340 Package PG-DIP-8-4 PG-DSO-8-1 SMD Functional Description The SAE 800 is a single-tone, dual-tone or triple-tone gong IC designed for a very wide supply voltage range. If the oscillator is set to f0 = kHz for example, the IC will issue in triple-tone- mode the minor and major third e2 C sharp a, corresponding to 660 Hz 550 Hz 440 Hz, in dual-tone-mode the minor third e2 C sharp, and in single-tone-mode the tone e2 derived from the fundamental frequency f0 f1 = f0 / 20, f2 = f0 / 24, f3 = f0 / When it is not triggered, the IC is in a standby state and only draws a few µA. It comes in a compact P-DIP-8-1 or P-DSO-8-1 SMD package and only requires a few external components. Semiconductor Group SAE 800 SAE 800 SAE 800 G Pin Configuration top view Pin Definitions and Functions Function Ground Output Supply Voltage Loudness Control ROSC Oscillator Resistor COSC Oscillator Capacitor Trigger 2 dual tone Trigger 1 single tone Functional Description cont’d An RC combination is needed to generate the fundamental frequency pin ROSC , COSC . The volume can be adjusted with another resistor pin L . The loudspeaker must be connected directly between the output Q and the power supply VS The current-sink principle combined with an integrated thermal shutdown with hysteresis makes the IC overload-protected and shortcircuit-protected. There are two trigger pins E1, E2 for setting single-tone, dual-tone or triple-tone mode. Semiconductor Group SAE 800 Block Diagram Semiconductor Group SAE 800 Circuit Description Trigger Positive pulses on inputs E1 and/or E2 trigger the IC. The hold feedback in the logic has a delay of several milliseconds. After this delay has elapsed, the tone sequence is started. This prevents parasitic spikes from producing any effect on the trigger pins. The following table shows the trigger options: E1 Triggered Grounded/open Triggered

PDF Datasheet Preview

Programmable Single-/Dual-/Triple- Tone Gong

Pb-free lead plating RoHS compliant

Features q Supply voltage range V to 18 V q Few external components no electrolytic capacitor q 1 tone, 2 tones, 3 tones programmable q Loudness control q Typical standby current 1 µA q Constant current output stage no oscillation q High-efficiency power stage q Short-circuit protection q Thermal shutdown

SAE 800

Bipolar IC

PG-DIP-8-4

PG-DSO-8-1

Type w SAE 800 w SAE 800 G
w New type
Ordering Code Q67000-A8339 Q67000-A8340

Package PG-DIP-8-4 PG-DSO-8-1 SMD

Functional Description

The SAE 800 is a single-tone, dual-tone or triple-tone gong IC designed for a very wide supply
voltage range. If the oscillator is set to f0 = kHz for example, the IC will issue in triple-tone-
mode the minor and major third e2 C sharp a, corresponding to 660 Hz 550 Hz 440 Hz, in dual-tone-mode the minor third e2 C sharp, and in single-tone-mode the tone e2 derived from
the fundamental frequency f0 f1 = f0 / 20, f2 = f0 / 24, f3 = f0 /

When it is not triggered, the IC is in a standby state and only draws a few µA. It comes in a compact P-DIP-8-1 or P-DSO-8-1 SMD package and only requires a few external components.

Semiconductor Group

SAE 800

SAE 800

SAE 800 G

Pin Configuration top view

Pin Definitions and Functions

Function

Ground

Output

Supply Voltage

Loudness Control

ROSC

Oscillator Resistor

COSC

Oscillator Capacitor

Trigger 2 dual tone

Trigger 1 single tone

Functional Description cont’d

An RC combination is needed to generate the fundamental frequency pin ROSC , COSC . The volume
can be adjusted with another resistor pin L . The loudspeaker must be connected directly between
the output Q and the power supply VS The current-sink principle combined with an integrated
thermal shutdown with hysteresis makes the IC overload-protected and shortcircuit-protected.

There are two trigger pins E1, E2 for setting single-tone, dual-tone or triple-tone mode.

Semiconductor Group

SAE 800

Block Diagram

Semiconductor Group

SAE 800

Circuit Description

Trigger

Positive pulses on inputs E1 and/or E2 trigger the IC. The hold feedback in the logic has a delay of several milliseconds. After this delay has elapsed, the tone sequence is started. This prevents parasitic spikes from producing any effect on the trigger pins.

The following table shows the trigger options:

E1 Triggered Grounded/open Triggered

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived SAE800GGEG Datasheet file may be downloaded here without warranties.

Datasheet ID: SAE800GGEG 638530