JLINK-ARM-AD

JLINK-ARM-AD Datasheet

JLINK-ARM-AD

Part	Datasheet
JLINK-ARM-AD	JLINK-ARM-AD (pdf)

PDF Datasheet Preview
JLINK-ARM-AD Users Manual Copyright 2011, Future Designs, Inc., All Rights Reserved The JLINK-ARM-AD is designed to work with FDI’s products that utilize a mini-JTAG connector. Products include the following: • uEZGUI-xxx-43WQS • uEZGUI-xxx-70WVE • SOMDIMM-LPCxxxx This product is intended for users who currently own a standard 20-pin JTAG debugger that is compatible with ARM based processor like the SEGGER J-Link, no debugger is included with this product. FDI products with a JTAG interface use a reduced size JTAG connector based on a 2mm header. This smaller connector provides 100% of the functionality of the standard 20-pin JTAG connector, but utilizes 70% less board space. J-Link Lite with Adapter Board Schematic: J-Link Ribbon Cable and Adapter Board Signal VCC Supply TRST TDI TMS TCK RTCK TDO RESET GND No Connect Standard JTAG pin out 1, 2 3 5 7 9 11 13 15 4, 6, 8, 10, 12, 14, 16, 18, 20 17, 19 mini-JTAG pin out 9 10 7 8 5 6 3 4 1 2 Information in this document is provided solely to enable the use of Future Designs products. FDI assumes no liability whatsoever, including infringement of any patent or copyright. FDI reserves the right to make changes to these specifications at any time, without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Future Designs, Inc. 2702 Triana Blvd, Huntsville, AL For more information on FDI or our products please visit NOTE The inclusion of vendor software products in this kit does not imply an endorsement of the product by Future Designs, Inc. 2011 Future Designs, Inc. All rights reserved.

PDF Datasheet Preview

JLINK-ARM-AD

Users Manual

Copyright 2011, Future Designs, Inc., All Rights Reserved

The JLINK-ARM-AD is designed to work with FDI’s products that utilize a mini-JTAG connector. Products include the following:
• uEZGUI-xxx-43WQS
• uEZGUI-xxx-70WVE
• SOMDIMM-LPCxxxx

This product is intended for users who currently own a standard 20-pin JTAG debugger that is compatible with ARM based processor like the SEGGER J-Link, no debugger is included with this product. FDI products with a JTAG interface use a reduced size JTAG connector based on a 2mm header. This smaller connector provides 100% of the functionality of the standard 20-pin JTAG connector, but utilizes 70% less board space.

J-Link Lite with Adapter Board Schematic:

J-Link Ribbon Cable and Adapter Board

Signal VCC Supply TRST TDI TMS TCK RTCK TDO RESET GND No Connect

Standard JTAG pin out 1, 2 3 5 7 9 11 13 15
4, 6, 8, 10, 12, 14, 16, 18, 20 17, 19
mini-JTAG pin out 9 10 7 8 5 6 3 4 1 2

Information in this document is provided solely to enable the use of Future Designs products. FDI assumes no liability whatsoever, including infringement of any patent or copyright. FDI reserves the right to make changes to these specifications at any time, without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Future Designs, Inc. 2702 Triana Blvd, Huntsville, AL

For more information on FDI or our products please visit

NOTE The inclusion of vendor software products in this kit does not imply an endorsement of the product by Future Designs, Inc. 2011 Future Designs, Inc. All rights reserved.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived JLINK-ARM-AD Datasheet file may be downloaded here without warranties.

Datasheet ID: JLINK-ARM-AD 635703