FTLX1341E2

FTLX1341E2 Datasheet

10GBASE-LRM X2 Transponder FTLX1341E2

Part	Datasheet
FTLX1341E2	FTLX1341E2 (pdf)

PDF Datasheet Preview
Product Specification RoHS-6 Compliant 10GBASE-LRM X2 Transponder FTLX1341E2 PRODUCT FEATURES Hot pluggable X2 MSA form factor Total power consumption W maximum RoHS-6 compliant lead-free Temperature range 0°C to 70°C Transmission distance up to 220m* Uncooled 1310 nm directly modulated Fabry-Perot FP laser Built In Advanced Electronic Dispersion Compensation EDC SC connector, multimode fiber Full duplex transmission mode Digital Optics Monitoring DOM Power supply V, V Adaptable Power Supply APS V XAUI electrical interface - 4 x Gb/s Ethernet Management and control via MDIO 2-wire bus 70-pin connector Separated signal/chassis ground Mid Pak module variance for front panel mounting De-latch mechanism with low extraction force IEEE 802.3aq-2006 10 Gb/s Ethernet transmission on legacy multimode fiber. The Finisar FTLX1341E2 transponder incorporates Electronic Dispersion Compensation EDC which provides correction for the severe modal dispersion that may occur during propagation through links up to 220m on legacy installed FDDI multimode fiber. The EDC device incorporates a Feed Forward Equalizer FFE and a Decision Feedback Equalizer DFE . The EDC also contains sophisticated clock recovery architecture for extracting a robust clock from extremely distorted signals. PRODUCT SELECTION FTLX1341E2 * Maximum reach as defined by IEEE. Longer reach possible depending upon link implementation. Finisar Corporation October 2008 FTLX1341E2 Product Specification October 2008 I. Pin Description Signal Name Level Management and Monitoring Ports MDIO Open Drain output 1.2V CMOS input CMOS PRTAD4 CMOS PRTAD3 CMOS PRTAD2 CMOS PRTAD1 CMOS PRTAD0 CMOS LASI Open Drain RESET CMOS

PDF Datasheet Preview

Product Specification RoHS-6 Compliant
10GBASE-LRM X2 Transponder FTLX1341E2

PRODUCT FEATURES

Hot pluggable X2 MSA form factor Total power consumption W maximum RoHS-6 compliant lead-free Temperature range 0°C to 70°C Transmission distance up to 220m* Uncooled 1310 nm directly modulated

Fabry-Perot FP laser Built In Advanced Electronic Dispersion

Compensation EDC SC connector, multimode fiber Full duplex transmission mode Digital Optics Monitoring DOM Power supply V, V Adaptable Power Supply APS V XAUI electrical interface
- 4 x Gb/s Ethernet Management and control via MDIO
2-wire bus 70-pin connector Separated signal/chassis ground Mid Pak module variance for
front panel mounting De-latch mechanism with low
extraction force

IEEE 802.3aq-2006 10 Gb/s Ethernet transmission on
legacy multimode fiber.

The Finisar FTLX1341E2 transponder incorporates Electronic Dispersion Compensation EDC which provides correction for the severe modal dispersion that may occur during propagation through links up to 220m on legacy installed FDDI multimode fiber. The EDC device incorporates a Feed Forward Equalizer FFE and a Decision Feedback Equalizer DFE . The EDC also contains sophisticated clock recovery architecture for extracting a robust clock from extremely distorted signals.

PRODUCT SELECTION

FTLX1341E2
* Maximum reach as defined by IEEE. Longer reach possible depending upon link implementation.

Finisar Corporation October 2008

FTLX1341E2 Product Specification October 2008

I. Pin Description

Signal Name Level

Management and Monitoring Ports

MDIO

Open Drain
output
1.2V CMOS
input

CMOS

PRTAD4

CMOS

PRTAD3

CMOS

PRTAD2

CMOS

PRTAD1

CMOS

PRTAD0

CMOS

LASI

Open Drain

RESET

CMOS

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived FTLX1341E2 Datasheet file may be downloaded here without warranties.

Datasheet ID: FTLX1341E2 635219