FDB-1042

FDB-1042 Datasheet

FDB-1042

Part	Datasheet
FDB-1042	FDB-1042 (pdf)

PDF Datasheet Preview
Product Specification QSFP+ Evaluation Board FDB-1042 The I2C pins SDA, SCL and GND have tap points available on top of the Evaluation Board while there are three taps on the bottom that are for loading the FW to the microprocessor for internal use only . The Evaluation Board has LED’s for the USB, Microcontroller Power, Module Power and External Power as well. It is compatible with all MSA compliant QSFP+ transceivers. Finisar’s FDB-1042 QSFP+ Evaluation Board is designed for testing and evaluating the QSFP+ transceiver and Quadwire Active Optical Cables. The board consists of a single QSFP+ edge connector and QSFP+ cage assembly, sixteen 50-ohm SMP coaxial connectors J1-J16 for the high-speed differential transmitter input and receiver output signals, and test points with LED’s for monitoring the following QSFP+ and Evaluation Board pins Module Select Module Reset SM Bus USB Bus Module Low Power Mode Module Interrupt Module Present Module Status Software that will provide additional functionality is planned to be added at a later date. It is recommended that the switch underneath the Evaluation Board be set to 1000 as the default setting. However, the user is free to change this at any time. SPECIFICATIONS The FDB-1042 QSFP+ Evaluation Board is powered by a supply voltage of 6V positive center at 2A from the 100V-240VAC, 5060Hz adaptor included with the purchase of the board . USB Interface Local Control and Status LED’s RX High-Speed Interface - 8 QSFP Cage External Power 2009 Finisar Corporation, Confidential Low Speed Interface Jumpers and LED’s TX High-Speed Interface - 8 Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1134 Tel. 1-408-548-1000 Fax 1-408-541-6138

PDF Datasheet Preview

Product Specification QSFP+ Evaluation Board

FDB-1042

The I2C pins SDA, SCL and GND have tap points available on top of the Evaluation Board while there are three taps on the bottom that are for loading the FW to the microprocessor for internal use only . The Evaluation Board has LED’s for the USB, Microcontroller Power, Module Power and External Power as well. It is compatible with all MSA compliant QSFP+ transceivers.

Finisar’s FDB-1042 QSFP+ Evaluation Board is designed for testing and evaluating the QSFP+ transceiver and Quadwire Active Optical Cables.

The board consists of a single QSFP+ edge connector and QSFP+ cage assembly, sixteen 50-ohm SMP coaxial connectors J1-J16 for the high-speed differential transmitter input and receiver output signals, and test points with LED’s for monitoring the following QSFP+ and Evaluation Board pins Module Select Module Reset SM Bus USB Bus Module Low Power Mode Module Interrupt Module Present Module Status

Software that will provide additional functionality is planned to be added at a later date.

It is recommended that the switch underneath the Evaluation Board be set to 1000 as the default setting. However, the user is free to change this at any time.

SPECIFICATIONS The FDB-1042 QSFP+ Evaluation Board is powered by a supply voltage of 6V positive center at 2A from the 100V-240VAC, 5060Hz adaptor included with the purchase of the board .

USB Interface

Local Control and Status

LED’s

RX High-Speed Interface - 8

QSFP Cage

External Power
2009 Finisar Corporation, Confidential

Low Speed Interface Jumpers and LED’s

TX High-Speed Interface - 8

Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1134 Tel. 1-408-548-1000 Fax 1-408-541-6138

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived FDB-1042 Datasheet file may be downloaded here without warranties.

Datasheet ID: FDB-1042 635188