ESPT-CLIPS-1K

ESPT-CLIPS-1K Datasheet

ESPT  Series

Part	Datasheet
ESPT-CLIPS-1K	ESPT-CLIPS-1K (pdf)

Related Parts	Information
ESPT-CLIPS-100	ESPT-CLIPS-100

PDF Datasheet Preview
ESPT  Series ESPT040 31-40 W ESPT050  41-50 W ESPT060 51-60 W 40 to 60 W Constant Current LED Drivers with Tri-Mode Dimming TRIAC, ELV & 0-10 V Nominal Input Voltage 120 to 277 Vac, 220 to 240 Vac Max. Output Power Output Voltage Output Current Efficiency Max. Case Temperature 24 to 56 Vdc 700 mA to A up to 87% typical 90°C measured at the hot spot CC Constant Current THD < 20% Power Factor Dimming Method Dimming Range Startup Time & 0 - 10V 1 - 100% % of Iout 400 ms TRIAC/ELV Dimmer + Dim - Dim ESPT + LEDs series 0-10 V Dimmer Plastic Case L 87 x W 60 x H 30mm  L x W x H in - LEDs Same features as the ESP series but with a thermally-enhanced plastic case ESPTxxxW models TRIAC and ELV dimming only at 120 Vac ESPTxxxE models ELV dimming only at 230 Vac 90°C maximum case hot spot temperature Class 2 power supply Lifetime 50,000 hours at 70°C case hot spot temperature some models have higher lifetime. Check lifetime curves in page 6 IP66-rated case with silicone-based potting Two 0-10V dimming are available: Linear 0-10 V dimming 10V=100%, 1V=10%, 0.1V=1%. Non-linear 0-10V dimming 10V to 8.1V=100%, 1V to 0.8V=1%, <0.8V Protections output open load, over-current and short-circuit  hiccup , and over-temperature with auto recovery Conducted and radiated EMI Compliant with FCC CFR Title 47 Part 15 Class B 120 Vac and Class A 277 Vac Complies with ENERGY DLC DesignLight and CA Title 24 technical requirements Worldwide safety approvals White Neutral Black Line ESPT series Purple + Dim Grey - Dim Red + LEDs Black - LEDs Wiring Diagram 1 - ORDERING INFORMATION - MODEL DESCRIPTION Series 31 - 40 W 41 - 50 W 51 - 60 W Nominal Vin 120 to 277 Vac Iout Vout Optional Max. features ERP Part Number ESPT040W-0700-56 ESPT040W-0800-42-Z1 1 ESPT040W-0900-42-Z1 1 ESPT050W-1050-42-Z1 1 ESPT050W-1200-42-Z1 1 ESPT050W-1400-34 ESPT060W-1400-42-Z1 1 ESPT040E-0800-42 ESPT040E-0900-42 ESPT050E-1050-42 ESPT050E-1200-42 ESPT060E-1400-42 Nominal Input Voltage Vac 120 to 277 120 to 277 120 to 277 120 to 277 120 to 277 120 to 277 120 to 277 220 to 240 220 to 240 220 to 240 220 to 240 220 to 240 Iout mA 700 800 900 1050 1200 1400 1400 800 900 1050 1200 1400 Max Output Power Vout Min Vdc Vout Nom Vdc Vout Max Vdc Open Loop no load Voltage Vdc Comments ESPT040W 31-40W 40 56 Linear 0-10V Dimming Profile 10V=100%, 1V=10% 24 42 24 42 ESPT050W 41-50W Non-linear 0-10V Dimming Profile 10V to 8.1V=100%, 1V to 0.8V=1%,<0.8V dim-to-off Non-linear 0-10V Dimming Profile 10V to 8.1V=100%, 1V to 0.8V=1%,<0.8V dim-to-off 24 42 24 42 23 34 Non-linear 0-10V Dimming Profile 10V to 8.1V=100%, 1V to 0.8V=1%,<0.8V dim-to-off Non-linear 0-10V Dimming Profile 10V to 8.1V=100%, 1V to 0.8V=1%,<0.8V dim-to-off Linear 0-10V Dimming Profile 10V=100%, 1V=10% ESPT060W 51-60W See ordering information for details See ordering information for details The rated output current for each model is achieved at Vac & at Vac for ESPTxxxW models, and at Vac for ESPTxxxE models. At nominal AC line voltage Includes load and current set point variations The driver does not operate outside of the regulation requirements for more than 500 ms during power on with nominal LED load and without dimmer. Measured at nominal LED voltage and nominal input voltage without dimming Calculated in accordance with the IES Lighting Handbook, 9th edition The dimming range is dependent on each specific dimmer. It may not be able to achieve 1% dimming with some dimmers. Dimming performance is optimal when the driver is operated at its nominal output voltage matching the LED nominal Vf forward voltage . Dimming performance may vary when the driver is operated near its minimum output voltage. Measured from application of AC line voltage to the time where light is visible about 10% of rated output current Measured from application of AC line voltage to 100% light output Complies with California Title 24 and ENERGY luminaire specification ESPT  Series ESPT040 31-40 W ESPT050  41-50 W ESPT060 51-60 W 40 to 60 W Constant Current LED Drivers with Tri-Mode Dimming TRIAC, ELV & 0-10 V 4 - 0-10 V DIMMING CONTROL ambient temperature Units Minimum Typical Maximum Notes +Dim Signal, -Dim Signal The ESPT series operate only with 0-10V dimmers that sink current. The method to dim the output current of the driver is done via the +Dim/-Dim Signal pins. The +Dim/-Dim signal pins can be used to adjust the output setting via a standard commercial wall dimmer, an external control voltage source 0 to 10 Vdc , or a variable resistor when using the recommended number of LEDs. The dimming input permits 1% to 100% dimming. Dimming Range % of Iout % The dimming range is dependent on each specific dimmer. It may not be able to achieve 1% dimming with some dimmers. 100 Dimming performance is optimal when the driver is operated at its nominal output voltage matching the LED nominal Vf forward voltage . Dimming performance may vary when the driver is operated near its minimum output voltage. Current Supplied by the +Dim Signal Pin Output Current Tolerance While Being Dimmed 1 ±8 The tolerance of the output current while being dimmed is +/-8% until down to 1V. Isolation The 0-10 V circuit is isolated from the AC input and meets Class II reinforced/double insulation power supply. 5 - ENVIRONMENTAL CONDITIONS Operating Case Temperature Tc Maximum Case Temperature Tc Storage Temperature Humidity Cooling Acoustic Noise Mechanical Shock Protection Vibration Protection MTBF Lifetime Warranty Units Minimum Typical Maximum Notes Case temperature measured at the hot spot tc see label in page 12 Case temperature measured at the hot spot tc see label in page 12 Non-condensing Convection cooled Measured at a distance of 1 foot 30 cm , without and with approved dimmers per EN60068-2-27 per EN60068-2-6 & EN60068-2-64 > 300,000 hours when operated at nominal input and output conditions, and at Tc 70°C hours 50,000 At Tc maximum case hot spot temperature see hot spot tc on label in page 12 Other models in the ESPT series have a longer lifetime. See details in section 5 years at Tc 70°C

PDF Datasheet Preview

ESPT  Series

ESPT040 31-40 W ESPT050  41-50 W ESPT060 51-60 W
40 to 60 W Constant Current LED Drivers with Tri-Mode Dimming TRIAC, ELV & 0-10 V

Nominal Input Voltage
120 to 277 Vac, 220 to 240 Vac

Max. Output Power

Output Voltage

Output Current

Efficiency

Max. Case Temperature
24 to 56 Vdc
700 mA to A
up to 87% typical
90°C measured at the hot spot

CC Constant Current

THD < 20%

Power Factor

Dimming Method

Dimming Range

Startup Time
& 0 - 10V
1 - 100% % of Iout
400 ms

TRIAC/ELV Dimmer
+ Dim - Dim

ESPT + LEDs series
0-10 V Dimmer

Plastic Case L 87 x W 60 x H 30mm  L x W x H in
- LEDs

Same features as the ESP series but with a thermally-enhanced plastic case

ESPTxxxW models TRIAC and ELV dimming only at 120 Vac ESPTxxxE models ELV dimming only at 230 Vac 90°C maximum case hot spot temperature Class 2 power supply Lifetime 50,000 hours at 70°C case hot spot temperature some
models have higher lifetime. Check lifetime curves in page 6 IP66-rated case with silicone-based potting Two 0-10V dimming are available:

Linear 0-10 V dimming 10V=100%, 1V=10%, 0.1V=1%. Non-linear 0-10V dimming 10V to 8.1V=100%, 1V to 0.8V=1%,
<0.8V Protections output open load, over-current and short-circuit 
hiccup , and over-temperature with auto recovery Conducted and radiated EMI Compliant with FCC CFR Title 47 Part
15 Class B 120 Vac and Class A 277 Vac Complies with ENERGY DLC DesignLight
and CA Title 24 technical requirements Worldwide safety approvals

White Neutral Black Line

ESPT series

Purple + Dim Grey - Dim Red + LEDs Black - LEDs

Wiring Diagram
1 - ORDERING INFORMATION - MODEL DESCRIPTION

Series 31 - 40 W
41 - 50 W 51 - 60 W

Nominal Vin 120 to
277 Vac

Iout

Vout Optional Max. features

ERP Part Number

ESPT040W-0700-56 ESPT040W-0800-42-Z1 1 ESPT040W-0900-42-Z1 1

ESPT050W-1050-42-Z1 1 ESPT050W-1200-42-Z1 1 ESPT050W-1400-34

ESPT060W-1400-42-Z1 1

ESPT040E-0800-42 ESPT040E-0900-42 ESPT050E-1050-42 ESPT050E-1200-42 ESPT060E-1400-42

Nominal Input

Voltage Vac
120 to 277 120 to 277 120 to 277
120 to 277 120 to 277 120 to 277
120 to 277
220 to 240 220 to 240
220 to 240 220 to 240
220 to 240

Iout mA
700 800 900
1050 1200 1400
1400
800 900 1050 1200 1400

Max Output Power

Vout Min Vdc

Vout Nom Vdc

Vout Max Vdc

Open Loop no load Voltage Vdc

Comments

ESPT040W 31-40W
40 56

Linear 0-10V Dimming Profile 10V=100%, 1V=10%
24 42
24 42

ESPT050W 41-50W

Non-linear 0-10V Dimming Profile 10V to 8.1V=100%, 1V to 0.8V=1%,<0.8V dim-to-off Non-linear 0-10V Dimming Profile 10V to 8.1V=100%, 1V to 0.8V=1%,<0.8V dim-to-off
24 42 24 42 23 34

Non-linear 0-10V Dimming Profile 10V to 8.1V=100%, 1V to 0.8V=1%,<0.8V dim-to-off Non-linear 0-10V Dimming Profile 10V to 8.1V=100%, 1V to 0.8V=1%,<0.8V dim-to-off Linear 0-10V Dimming Profile 10V=100%, 1V=10%

ESPT060W 51-60W
See ordering information for details See ordering information for details The rated output current for each model is achieved at Vac & at Vac for ESPTxxxW models, and at Vac for ESPTxxxE models. At nominal AC line voltage Includes load and current set point variations The driver does not operate outside of the regulation requirements for more than 500 ms during power on with nominal LED load and without dimmer. Measured at nominal LED voltage and nominal input voltage without dimming Calculated in accordance with the IES Lighting Handbook, 9th edition The dimming range is dependent on each specific dimmer. It may not be able to achieve 1% dimming with some dimmers. Dimming performance is optimal when the driver is operated at its nominal output voltage matching the LED nominal Vf forward voltage . Dimming performance may vary when the driver is operated near its minimum output voltage. Measured from application of AC line voltage to the time where light is visible about 10% of rated output current Measured from application of AC line voltage to 100% light output Complies with California Title 24 and ENERGY luminaire specification

ESPT  Series

ESPT040 31-40 W ESPT050  41-50 W ESPT060 51-60 W
40 to 60 W Constant Current LED Drivers with Tri-Mode Dimming TRIAC, ELV & 0-10 V
4 - 0-10 V DIMMING CONTROL ambient temperature

Units Minimum Typical Maximum

Notes
+Dim Signal, -Dim Signal

The ESPT series operate only with 0-10V dimmers that sink current. The method to dim the output current of the driver is done via the +Dim/-Dim Signal pins. The +Dim/-Dim signal pins can be used to adjust the output setting via a standard commercial wall dimmer, an external control voltage source 0 to 10 Vdc , or a variable resistor when using the recommended number of LEDs. The dimming input permits 1% to 100% dimming.

Dimming Range % of Iout %
The dimming range is dependent on each specific dimmer. It may not be able to achieve 1% dimming with some dimmers. 100 Dimming performance is optimal when the driver is operated at its nominal output voltage matching the LED nominal Vf forward voltage . Dimming performance may vary when the driver is operated near its minimum output voltage.

Current Supplied by the
+Dim Signal Pin

Output Current Tolerance

While Being Dimmed
1 ±8 The tolerance of the output current while being dimmed is +/-8% until down to 1V.

Isolation

The 0-10 V circuit is isolated from the AC input and meets Class II reinforced/double insulation power supply.
5 - ENVIRONMENTAL CONDITIONS

Operating Case Temperature Tc

Maximum Case Temperature Tc Storage Temperature Humidity Cooling Acoustic Noise Mechanical Shock Protection Vibration Protection MTBF

Lifetime

Warranty

Units Minimum

Typical

Maximum

Notes

Case temperature measured at the hot spot tc see label
in page 12

Case temperature measured at the hot spot tc see label
in page 12

Non-condensing

Convection cooled

Measured at a distance of 1 foot 30 cm , without and
with approved dimmers
per EN60068-2-27
per EN60068-2-6 & EN60068-2-64
> 300,000 hours when operated at nominal input and output conditions, and at Tc 70°C
hours 50,000
At Tc maximum case hot spot temperature see hot spot tc on label in page 12 Other models in the ESPT series have a longer lifetime. See details in section
5 years at Tc 70°C

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ESPT-CLIPS-1K Datasheet file may be downloaded here without warranties.

Datasheet ID: ESPT-CLIPS-1K 511927