PI4ULS3V16ZFEX

PI4ULS3V16ZFEX Datasheet


PI4ULS3V16

Part Datasheet
PI4ULS3V16ZFEX PI4ULS3V16ZFEX PI4ULS3V16ZFEX (pdf)
Related Parts Information
PI4ULS3V16ZFE PI4ULS3V16ZFE PI4ULS3V16ZFE
PI4ULS3V16AEX PI4ULS3V16AEX PI4ULS3V16AEX
PI4ULS3V16AE PI4ULS3V16AE PI4ULS3V16AE
PDF Datasheet Preview
PI4ULS3V16
1.2V to 3.6V Universal Bidirectional Level Shifter with Automatic Direction Control
 PI4ULS3V16 is designed for low voltage operation 1.2V to 3.6V
 Universal bidirectional level shifting with automatic direction control
 Fast bus speeds up to 180 Mbps for push-pull application
 Drive Capability 12mA  Independent translation of each bit  Each supply rail is configurable over supply range  ESD Protection exceeds JESD22  - 2000V Human Body Model A114-B  -200V Machine Model A115-A  Latch-up performance exceeds 100mA per JESD
78  Industrial operation at -40°C to +85°C  Package 56-contact plastic 197-mil TQFN

Pin Configuration

PI4ULS3V16, is a 16-bit dual-octal non-inverting bus transceiver with two separate supply rails A port VCCA and B port VCCB are set to operate at 1.2V to 3.6V. This arrangement permits universal bidirectional translation of differential signal levels over the voltage ranges.

The PI4ULS3V16 is designed for asynchronous communication between data buses. Data is transmitted from the A bus to the B bus, or vice versa, without direction control. All AX, and BX are tri-stated when data is coming from both directions at the same time. The output-enable OE input is used to disable outputs so buses are isolated.

The control pins xSEL, xOE, TEST_EN and OUT_SEL are supplied by VCCB.

To ensure the high impedance state during power-
up or power- down, the output-enable OE input should
be tied to VCC through a pull-up resistor the minimum
value of the resistor is determined by the current-sinking
capability of the driver.
 Voltage Translation  Bus Relay

Pin Description

Pin Name
xSEL xAx xBx TEST_EN OUT_SEL GND VccA,VCCB

TSTx
3-State Output Enable Inputs Active Low

Outputs Loading Selection Side A Inputs/Outputs Side B Inputs/Outputs Enable Test Mode Output impedance select Ground Power Internal test pins. For normal usage, please tie to ground

TQFN-56L Top View
2013-07-0004

PT0483 07/12/13 1

PI4ULS3V16 1.2V to 3.6V Universal Bidirectional Level

Shifter with Automatic Direction Control

Block Diagram

Truth Table

Inputs
xOE 2SEL 1SEL

Outputs Loading 2

CL 50pF CL 30pF CL 20pF CL 10pF

Operation

Bus B data to Bus A, or Bus A data to Bus B

Z Isolation

Note H = HIGH Signal Level, L = LOW Signal Level

X = Don’t Care or Irrelevant, Z = High Impedance Refer to Figure2for output Loading Chart

Test Mode / Output Impedance Select

Figure 1 Block Diagram
Ordering Information

PI4ULS3V16ZFE

Note E = Pb-free Adding X Suffix= Tape/Reel

Package Code ZF

Package Lead free and Green 56-pin TQFN 5x11

Pericom Semiconductor Corporation  1-800-435-2336 

Pericom reserves the right to make changes to its products or specifications at any time, without notice, in order to improve design or performance and to supply the best possible product. Pericom does not assume any responsibility for use of any circuitry described other than the circuitry embodied in Pericom product. The company makes no representations that circuitry described herein is free from patent infringement or other rights, of Pericom.
2013-07-0004

PT0483 07/12/13 7
More datasheets: IMN351816M12 | ATR4256-TKQY | ATR4256-TKSY | KXT 111 LHS | KXT 131 LHS | KXT 121 LHS | 3142 | 18040ACU | FAN2013MPX | PI4ULS3V16ZFE


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived PI4ULS3V16ZFEX Datasheet file may be downloaded here without warranties.

Datasheet ID: PI4ULS3V16ZFEX 510069