SEN0209

SEN0209 Datasheet

Gravity Flexible Piezo Film Vibration Sensor SKU SEN0209

Part	Datasheet
SEN0209	SEN0209 (pdf)

PDF Datasheet Preview
Gravity Flexible Piezo Film Vibration Sensor SKU SEN0209 Introduction This is an Arduino compatible piezo film vibration sensor. It is made up of flexible piezo film and converter board. The sensor is able to detect vibration, flexibility, impact and touch. The film is a flexible component comprising a 28 µm thick piezoelectric PVDF polymer film with screen-printed Ag-ink electrodes, laminated to a mm polyester substrate, and fitted with two crimped contacts. As the piezo film is displaced from the mechanical neutral axis, bending creates very high strain within the piezo polymer and therefore high voltages about ±90V are generated. When the assembly is deflected by direct contact, the device acts as a flexible "switch", and the generated output is sufficient to trigger MOSFET or CMOS stages directly. The module uses universal Gravity 3Pin interface, easy plug, plug and play. It comes with Digital/Analog two kinds of output signal, suitable for all kinds of different applications. The piezo vibration sensor is not only able to detect strong shocks, but also to detect slight vibrations. There is an on-board sensitivity adjustment potentiometer, you can adjust it to increase/decrease the output threshold value. Meanwhile, the piezo film sensor has a wide dynamic range 0.001Hz~1000MHz also guarantees an excellent measuring performance. Specification • Operating Voltage 5V • Interface Type Gravity PH2.0 3Pin interface • Operating Temperature 0 ° C to 85 ° C • Storage Temperature -40 ° C to 85 ° C • Dimension 27mm * 22mm • Weight 10 g Board Overview Num 1 2 3 Label GND VCC Signal Description GND VCC Signal Flexible Piezo Film Vibration Sensor Tutorial In this tutorial, we'll show you the sensor usage. Watch the serial monitor and LED "L" state. Note The sensitivity potentiometer control the output threshold. When it ro tates towards "MAX" direction, it need more swing to trigger sensor. Requirements • Hardware DFRduino UNO x1 Flexible Piezo Film Vibration Sensor x1 M-M/F-M/F-F Jumper wires • Software Arduino IDE, Click to Download Arduino IDE from Connection Diagram Note Turn the switch to "D" side Sample Code * Piezo Vibration Sensor * * This example The sensors detect vibration * * V1.0 * 2016-2-26 * GNU Lesser General Public License. * See for details. * All above must be included in any redistribution * #define sensorPin A1 #define ledPin 13 void setup Serial.begin 115200 pinMode ledPin,OUTPUT ; void loop int x=analogRead sensorPin Serial.println x if x>500 digitalWrite 13,HIGH else digitalWrite 13,LOW delay 50 ; Expected Results For any questions, advice or cool ideas to share, please visit the DFRobot Forum. 6-7-17

PDF Datasheet Preview

Gravity Flexible Piezo Film Vibration Sensor SKU SEN0209

Introduction

This is an Arduino compatible piezo film vibration sensor. It is made up of flexible piezo film and converter board. The sensor is able to detect vibration, flexibility, impact and touch. The film is a flexible component comprising a 28 µm thick piezoelectric PVDF polymer film with screen-printed Ag-ink electrodes, laminated to a mm polyester substrate, and fitted with two crimped contacts. As the piezo film is displaced from the mechanical neutral axis, bending creates very high strain within the piezo polymer and therefore high voltages about ±90V are generated. When the assembly is deflected by direct contact, the device acts as a flexible "switch", and the generated output is sufficient to trigger MOSFET or CMOS stages directly. The module uses universal Gravity 3Pin interface, easy plug, plug and play. It comes with Digital/Analog two kinds of output signal, suitable for all kinds of different applications. The piezo vibration sensor is not only able to detect strong shocks, but also to detect slight vibrations. There is an on-board sensitivity adjustment potentiometer, you can adjust it to increase/decrease the output threshold value. Meanwhile, the piezo film sensor has a wide dynamic range 0.001Hz~1000MHz also guarantees an excellent measuring performance.

Specification
• Operating Voltage 5V
• Interface Type Gravity PH2.0 3Pin interface
• Operating Temperature 0 ° C to 85 ° C
• Storage Temperature -40 ° C to 85 ° C
• Dimension 27mm * 22mm
• Weight 10 g

Board Overview

Num 1 2 3

Label GND VCC Signal

Description GND VCC Signal

Flexible Piezo Film Vibration Sensor

Tutorial

In this tutorial, we'll show you the sensor usage. Watch the serial monitor and LED "L" state.

Note The sensitivity potentiometer control the output threshold. When it ro tates towards "MAX" direction, it need more swing to trigger sensor.

Requirements
• Hardware DFRduino UNO x1 Flexible Piezo Film Vibration Sensor x1 M-M/F-M/F-F Jumper wires
• Software

Arduino IDE, Click to Download Arduino IDE from

Connection Diagram

Note Turn the switch to "D" side

Sample Code
* Piezo Vibration Sensor * * This example The sensors detect vibration
* * V1.0 * 2016-2-26
* GNU Lesser General Public License. * See for details. * All above must be included in any redistribution * #define sensorPin A1 #define ledPin 13 void setup

Serial.begin 115200 pinMode ledPin,OUTPUT ;
void loop int x=analogRead sensorPin Serial.println x if x>500 digitalWrite 13,HIGH else digitalWrite 13,LOW delay 50 ;

Expected Results

For any questions, advice or cool ideas to share, please visit the DFRobot Forum.
6-7-17

More datasheets: 2W01G | 2W04G | 2W08G | 2W10G | 2W06G | PN-DESIGNKIT-2 | FQPF11N40T | FFPF05U60DNTU | FJAFS1720TU | 1485

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived SEN0209 Datasheet file may be downloaded here without warranties.

Datasheet ID: SEN0209 509110