SEN0004

SEN0004 Datasheet

SRF01 ultrasonic sensor SKU:SEN0004

Part	Datasheet
SEN0004	SEN0004 (pdf)

PDF Datasheet Preview
SRF01 ultrasonic sensor SKU:SEN0004 INTRODUCTION It is a tiny, with impressive performance single transducer sensor. The SRF01 Ultrasonic Range Finder uses Devantech's 2nd generation AutoTune technology that allows ranging from 6 meters all the way down to zero on a single transducer sonar module. Connect up to 16 SRF01 modules to a single microcontroller line, using a simple 3.3~5V tolerant TTL serial networking protocol of a "Break", 2-byte sensor address, and the command. The SRF01 at that address will respond appropriately check the resources . Two different operating modes are available when using the SRF01. The standard mode is "Advanced Mode", allowing ranging all the way down to the transducer 0cm . This requires the SRF01 taking 5 readings out to a range of 30cm or more and setting an internal calibration bit. "Standard Mode" does not require this calibration routine, but decreases the effective range to 18cm to 6m 7" to make mounting a snap, a rubber grommet is supplied to mount the SRF01, which can secure the sensor in a panel no thicker than 1.7mm Supplied with Mounting Grommet. 3-pin JST cable is not included. SPECIFICATION • Voltage - 3.3v to 12v • Current - 25mA Ranging. 11mA Standby. 55uA Sleep. • Frequency - 40KHz • Range - 18cm 7 in to 600cm 236 in Industrial spec', no calibration required . • Range - 0cm to 600cm 236 in Hobby spec' after auto-calibration . • Connection - One Pin Serial Bus 9600 baud. • Up to 16 SRF01's connected to a single pin on your controller. • Units - Range reported in cm or inches. • Very light weight, just 2.7gm SHIPPING LIST • SRF01 ultrasonic sensor x1 5-30-17

PDF Datasheet Preview

SRF01 ultrasonic sensor SKU:SEN0004

INTRODUCTION

It is a tiny, with impressive performance single transducer sensor. The SRF01 Ultrasonic Range Finder uses Devantech's 2nd generation AutoTune technology that allows ranging from 6 meters all the way down to zero on a single transducer sonar module. Connect up to 16 SRF01 modules to a single microcontroller line, using a simple 3.3~5V tolerant TTL serial networking protocol of a "Break", 2-byte sensor address, and the command. The SRF01 at that address will respond appropriately check the resources . Two different operating modes are available when using the SRF01. The standard mode is "Advanced Mode", allowing ranging all the way down to the transducer 0cm . This requires the SRF01 taking 5 readings out to a range of 30cm or more and setting an internal calibration bit. "Standard Mode" does not require this calibration routine, but decreases the effective range to 18cm to 6m 7" to make mounting a snap, a rubber grommet is supplied to mount the SRF01, which can secure the sensor in a panel no thicker than 1.7mm

Supplied with Mounting Grommet. 3-pin JST cable is not included.

SPECIFICATION
• Voltage - 3.3v to 12v
• Current - 25mA Ranging. 11mA Standby. 55uA Sleep.
• Frequency - 40KHz
• Range - 18cm 7 in to 600cm 236 in Industrial spec', no calibration required .
• Range - 0cm to 600cm 236 in Hobby spec' after auto-calibration .
• Connection - One Pin Serial Bus 9600 baud.
• Up to 16 SRF01's connected to a single pin on your controller.
• Units - Range reported in cm or inches.
• Very light weight, just 2.7gm

SHIPPING LIST
• SRF01 ultrasonic sensor x1
5-30-17

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived SEN0004 Datasheet file may be downloaded here without warranties.

Datasheet ID: SEN0004 509042