MB96F348RSCPMC-GSE2
MB96F348RSCPMC-GSE2 Datasheet
FME-MB96340 rev 10
| Part | Datasheet |
|---|---|
MB96F348RSCPMC-GSE2 |
MB96F348RSCPMC-GSE2 (pdf) |
| Related Parts | Information |
|---|---|
MB96F346RWCPQC-GSE2 |
MB96F346RWCPQC-GSE2 |
MB96F347RSCPQC-GSE2 |
MB96F347RSCPQC-GSE2 |
|
MB96F347RWCPMC-GSE2 |
MB96F347RWCPMC-GSE2 |
MB96F347RWCPQC-GSE2 |
MB96F347RWCPQC-GSE2 |
MB96F348RSCPQC-GSE2 |
MB96F348RSCPQC-GSE2 |
|
MB96F348RWCPMC-GSE2 |
MB96F348RWCPMC-GSE2 |
MB96F348RWCPQC-GSE2 |
MB96F348RWCPQC-GSE2 |
|
MB96F346RWCPMC-GSE2 |
MB96F346RWCPMC-GSE2 |
|
MB96F347RSCPMC-GSE2 |
MB96F347RSCPMC-GSE2 |
| PDF Datasheet Preview |
|---|
| 16-bit Proprietary Microcontroller CMOS F2MC-16FX MB96340 Series MB96345/346 MB96F345 *1 MB96F346/F347/F348 • DESCRIPTION MB96340 series is based on Fujitsu’s advanced 16FX architecture 16-bit with instruction pipeline for RISC-like performance . The CPU uses the same instruction set as the established 16LX series - thus allowing for easy migration of 16LX Software to the new 16FX products. 16FX improvements compared to the previous generation include improved performance - even at the same operation frequency, reduced power consumption and faster start-up time. For highest processing speed at optimized power consumption an internal PLL can be selected to supply the CPU with up to 56MHz operation frequency from an external 4MHz resonator. The result is a minimum instruction cycle time of 17.8ns going together with excellent EMI behavior. An on-chip clock modulation circuit reduces emission peaks in the frequency spectrum. The emitted power is minimized by the on-chip voltage regulator that reduces the internal CPU voltage. A clock tree allows to select suitable operation frequencies for peripheral resources independent of the CPU speed. *1 These devices are under development and is preliminary. These products under development may change its without notice. Note F2MC is the abbreviation of Fujitsu Flexible Microcontroller Copyright 2010 FUJITSU SEMICONDUCTOR LIMITED All rights reserved MB96340 Series • FEATURES Technology • 0.18µm CMOS • F2MC-16FX CPU • Up to 56 MHz internal, ns instruction cycle time • Optimized instruction set for controller applications bit, byte, word and long-word data types 23 different addressing modes barrel shift variety of pointers • 8-byte instruction execution queue • Signed multiply 16-bit x 16-bit and divide 32-bit/16-bit instructions available • On-chip PLL clock multiplier x1 - x25, x1 when PLL stop • 3 MHz - 16 MHz external crystal oscillator clock maximum frequency when using ceramic resonator depends on Q-factor . • Up to 56 MHz external clock for devices with fast clock input feature • 32-100 kHz subsystem quartz clock System clock • 100kHz/2MHz internal RC clock for quick and safe startup, oscillator stop detection, watchdog • Clock source selectable from main- and subclock oscillator part number suffix “W” and on-chip RC oscillator, independently for CPU and 2 clock domains of peripherals. • Low Power Consumption - 13 operating modes different Run, Sleep, Timer modes, Stop mode • Clock modulator On-chip voltage regula- • Internal voltage regulator supports reduced internal MCU voltage, offering low EMI and low power consumption figures Low voltage reset • Reset is generated when supply voltage is below minimum. Code Security • Protects ROM content from unintended read-out • Replaces ROM content Memory Patch Function • Can also be used to implement embedded debug support • Automatic transfer function independent of CPU, can be assigned freely to resources • Fast Interrupt processing Interrupts • 8 programmable priority levels • Non-Maskable Interrupt NMI Timers • Three independent clock timers 23-bit RC clock timer, 23-bit Main clock timer, 17-bit Sub clock timer • ORDERING INFORMATION MCU with CAN controller MB96345YSA PQC-GSE2 *1 MB96345RSA PQC-GSE2 *1 MB96345YWA PQC-GSE2 *1 MB96345RWA PQC-GSE2 *1 MB96345YSA PMC-GSE2 *1 MB96345RSA PMC-GSE2 *1 MB96345YWA PMC-GSE2 *1 MB96345RWA PMC-GSE2 *1 MB96346YSA PQC-GSE2 *1 MB96346RSA PQC-GSE2 *1 MB96346YWA PQC-GSE2 *1 MB96346RWA PQC-GSE2 *1 MB96346YSA PMC-GSE2 *1 MB96346RSA PMC-GSE2 *1 MB96346YWA PMC-GSE2 *1 MB96346RWA PMC-GSE2 *1 MB96F345FSB PQC-GSE2 *1 MB96F345DSB PQC-GSE2 *1 MB96F345FWB PQC-GSE2 *1 MB96F345DWB PQC-GSE2 *1 MB96F345FSB PMC-GSE2 *1 MB96F345DSB PMC-GSE2 *1 MB96F345FWB PMC-GSE2 *1 MB96F345DWB PMC-GSE2 *1 Flash/ROM 160KB ROM 288KB Flash A 160KB Data Flash A 64KB Persistent Subclock Low Volt- age Reset Package 100 pin Plastic QFP FPT-100P-M22 100 pin Plastic LQFP FPT-100P-M20 100 pin Plastic QFP FPT-100P-M22 100 pin Plastic LQFP FPT-100P-M20 100 pin Plastic QFP FPT-100P-M22 100 pin Plastic LQFP FPT-100P-M20 MB96340 Series MCU with CAN controller MB96F346YSB PQC-GSE2 MB96F346RSB PQC-GSE2 MB96F346YWB PQC-GSE2 MB96F346RWB PQC-GSE2 MB96F346YSB PMC-GSE2 MB96F346RSB PMC-GSE2 MB96F346YWB PMC-GSE2 MB96F346RWB PMC-GSE2 MB96F346YSC PQC-GSE2*1 MB96F346RSC PQC-GSE2*1 MB96F346YWC PQC-GSE2*1 MB96F346RWC PQC-GSE2*1 MB96F346YSC PMC-GSE2*1 MB96F346RSC PMC-GSE2*1 MB96F346YWC PMC-GSE2*1 MB96F346RWC PMC-GSE2*1 MB96F347YSB PQC-GSE2 MB96F347RSB PQC-GSE2 MB96F347YWB PQC-GSE2 MB96F347RWB PQC-GSE2 MB96F347YSB PMC-GSE2 MB96F347RSB PMC-GSE2 MB96F347YWB PMC-GSE2 MB96F347RWB PMC-GSE2 MB96F347YSC PQC-GSE2*1 MB96F347RSC PQC-GSE2*1 MB96F347YWC PQC-GSE2*1 MB96F347RWC PQC-GSE2*1 MB96F347YSC PMC-GSE2*1 MB96F347RSC PMC-GSE2*1 MB96F347YWC PMC-GSE2*1 MB96F347RWC PMC-GSE2*1 Flash/ROM Flash A 288KB Flash A 416KB Persistent Subclock Low Volt- age Reset Package 100 pin Plastic QFP FPT-100P-M22 100 pin Plastic LQFP FPT-100P-M20 100 pin Plastic QFP FPT-100P-M22 100 pin Plastic LQFP FPT-100P-M20 100 pin Plastic QFP FPT-100P-M22 100 pin Plastic LQFP FPT-100P-M20 2007-08-02 Electrical characteristics updates, Product lineup, changes and ordering information 2007-09-12 Addition of the electrical characteristic examples and the LVD characteristics updates of the DC characteristics. Pin circuit type drawing 2007-11-21 LVD typo correction. Update of the DC characteristics. Typos corrections. 2007-12-04 Absolute maximum rating asterisks numbering corrected. Typos page 59 Hardware -> Hardware. IO map table regenerated. Typos corrections. IO circuit drawings Renaming of the Main/Satellite Flash into Flash memory A/B. Memory map reworked. MB96340 Series Prelim 8 2008-02-04 • Satellite Flash -> 32kB Data Flash • MB96345 added under development • MB96F348 TSA/HSA/TWA/HWA removed outdated devices • Block diagram and pin assignment corrected existing resource pins • Pin function table corrected • I/O circuit type diagrams corrected • Memory map cleaned up • "Flash sector replaced by corrected "User ROM Memory map for Flash devices", “ROM replaced by “User ROM Memory map for Mask ROM devices” • Parallel Flash programming pinning removed • IO map table regenerated - Port register Naming style corrected - Memory control registers renamed Main/Sat -> A/B - addresses after 000BFFh removed • Absolute maximum ratings Pd and Ta more precisely • oscillator input levels in oscillation mode with external clock added • Run and Sleep mode currents 96/48MHz and 72/36MHz settings added • Run mode current spec in 48/24MHz mode corrected • Maximum CLKS1/2 frequency for all devices correctly • Maximum CLKP2 for MB96F34xY/R/Axx corrected • External bus timings missing conditions added and readability improved • Alarm comparator spec updated transition voltages • MB96V300A removed • Ordering information updated • Typos and formatting corrected MB96340 Series 2009-01-09 • Format adjusted to Fujitsu Microelectronics datasheet standard mainly style changes and notes and disclaimer added • Numbering of Electrical Characteristics subchapters automated • Note about devices under development • I/O map Note added about reserved addresses • ICCSPLL for CLKS1=96MHz mode increased by 1mA • Serial programming interface Note about handshaking pins improved • AD converter channel offset to 4LSB • package code of MB96V300 corrected in ordering information • Added voltage condition to pull-up resistance spec • Lineup Term “Data Flash” replaced by “independent 32KB Flash” • Ordering information column “Independent 32KB Data Flash” replaced by new column “Flash/ROM”, column “Remarks” removed • package dimension drawing with additional notes added • Empty pages removed • Alarm comparator Power supply current max values increased, comparison time reduced, mode transition time and power-up stabilization time newly added • Handling devices Notes added about Serial communication and about using ceramic resonators. • Feature list and AC Characteristics 16MHz maximum frequency is valid for crystal oscillators. For resonators, maximum frequency depends on Q-factor • AC characteristics PLL phase skew spec added, CLKVCO min=64MHz • VOL3 spec improved spec valid for 3mA load for full Vcc range • MB96F345 added • Preliminary DC spec of MB96345/346 added • Permitted power dissipation of Flash devices in QFP package improved • C-Pin cap spec updated 4.7uF-10uF capacitor with tolerance permitted • “Preliminary” watermark removed MB96340 Series 2010-06-23 • I/O map IOABK0-5 added at address 000A00H-000A05H • Ordering Information “A” added to all MB96F345 device versions • AD converter IAIN spec improved 1uA valid up to 105deg, 1.2uA above 105deg • Corrected MB96F345 part names in ordering information • Low voltage detector Detection levels of MB96F345 updated • Example characteristics updated, new added showing dependency of PLL Run mode current on frequency • Updated Power Supply current spec in Run/Sleep/Timer/Stop modes new spec items in PLL Run/Sleep mode, small adjustment of most other values • Note added that PLL phase jitter spec does not include jitter coming from Main clock • Alarm comparator Maximum power-up stabilization time increased to 10ms • Removed PHDR register from IO map • Note added in DC characteristics how to select driving strength of ports • I2C AC spec updated tof, Cb and tSP spec added, wrong footnotes and Con- dition removed • I/O Circuit type Note added for type “N” slew rate control according to I2C spec • Package dimension Added the following sentence under the “Please the latest Package dimension by following URL. • AD converter Impact of input pin capacitance and external capacitance added to formula for calculation of the sampling time • Added of RC clock stabilization time • Feature description I2C ‘8-bit addressing’ corrected to ‘7-bit addressing’ • Feature description PPG ‘Reload timer as clock input’ corrected to ‘Reload timer as clock input’ • Company name updated on the cover page Fujitsu Microelectronics Limited - > Fujitsu Semiconductor Limited • ICCLVD updated, at 125deg typical value is 7uA and maximum value is 20uA • Ordering information added devices under development MB96F346A*C, MB96F347A*C, MB96F348A*C, MB96F346Y*C, MB96F347Y*C, MB96F348Y*C, MB96F346R*C, MB96F347R*C, MB96F348R*C MB96340 Series MB96340 Series FUJITSU SEMICONDUCTOR LIMITED Nomura Fudosan Shin-yokohama Bldg. 10-23, Shin-yokohama 2-Chome, Kohoku-ku Yokohama Kanagawa 222-0033, Japan Tel +81-45-415-5858 For further information please contact: North and South America FUJITSU MICROELECTRONICS AMERICA, INC. 1250 E. Arques Avenue, M/S 333 Sunnyvale, CA 94085-5401, U.S.A. Tel +1-408-737-5600 Fax +1-408-737-5999 Asia FUJITSU MICROELECTRONICS ASIA PTE. LTD. 151 Lorong Chuan, #05-08 New Tech Park 556741 Singapore Tel +65-6281-0770 Fax +65-6281-0220 Europe FUJITSU MICROELECTRONICS EUROPE GmbH Pittlerstrasse 47, 63225 Langen, Germany Tel +49-6103-690-0 Fax +49-6103-690-122 FUJITSU MICROELECTRONICS SHANGHAI CO., LTD. Rm. 3102, Bund Center, No.222 Yan An Road E , Shanghai 200002, China Tel +86-21-6146-3688 Fax +86-21-6335-1605 Korea FUJITSU MICROELECTRONICS KOREA LTD. 206 Kosmo Tower Building, 1002 Daechi-Dong, Gangnam-Gu, Seoul 135-280, Republic of Korea Tel +82-2-3484-7100 Fax +82-2-3484-7111 FUJITSU MICROELECTRONICS PACIFIC ASIA LTD. 10/F., World Commerce Centre, 11 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel +852-2377-0226 Fax +852-2376-3269 Specifications are subject to change without notice. For further information please contact each office. All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU SEMICONDUCTOR device FUJITSU SEMICONDUCTOR does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU SEMICONDUCTOR or any third party or does FUJITSU SEMICONDUCTOR warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU SEMICONDUCTOR assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated 1 for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system , or 2 for use requiring extremely high reliability i.e., submersible repeater and artificial satellite . Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of overcurrent levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Edited Sales Promotion Department |
| More datasheets: MAX5533EUA | NDT453N | RFD8P05SM | RFD8P05 | RFP8P05 | LTS4840AY | MB96F346RWCPQC-GSE2 | MB96F347RSCPQC-GSE2 | MB96F347RWCPMC-GSE2 | MB96F347RWCPQC-GSE2 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MB96F348RSCPMC-GSE2 Datasheet file may be downloaded here without warranties.