MB95F332H/F332K/F333H/F333K/F334H/F334K
Part | Datasheet |
---|---|
![]() |
MB95F333KPMC-G-SNE2 (pdf) |
Related Parts | Information |
---|---|
![]() |
MB95F334KP-G-SH-SNE2 |
![]() |
MB95F334KPMC-G-SNE2 |
![]() |
MB95F332HWQN-G-SNE1 |
![]() |
MB95F332KP-G-SH-SNE2 |
![]() |
MB95F332KPMC-G-SNE2 |
![]() |
MB95F333KP-G-SH-SNE2 |
![]() |
MB95F334KWQN-G-SNE1 |
![]() |
MB95F332KWQN-G-SNE1 |
PDF Datasheet Preview |
---|
MB95F332H/F332K/F333H/F333K/F334H/F334K F2MC-8FX MB95330H Series 8-bit Microcontrollers MB95330H is a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of this series contain a variety of peripheral resources. F2MC-8FX CPU core Instruction set optimized for controllers • Multiplication and division instructions • 16-bit arithmetic operations • Bit test branch instructions • Bit manipulation instructions, etc. Clock • Selectable main clock source Main OSC clock up to MHz, maximum machine clock frequency MHz External clock up to MHz, maximum machine clock frequency MHz Main CR clock MHz ±2%, maximum machine clock frequency MHz • Selectable subclock source Sub-OSC clock kHz External clock kHz Sub-CR clock Typ 100 kHz, Min 50 kHz, Max 200 kHz Timer • 8/16-bit composite timer 2 channels • 8/16-bit PPG 3 channels • 16-bit PPG 1 channel can work independently or together with the multi-pulse generator • 16-bit reload timer 1 channel can work independently or together with the multi-pulse generator • Time-base timer 1 channel • Watch prescaler 1 channel UART/SIO 1 channel • Full duplex double buffer • Capable of clock-asynchronous UART serial data transfer and clock-synchronous SIO serial data transfer I2C 1 channel • Built-in wake-up function Multi-pulse generator MPG for DC motor control 1 channel • 16-bit reload timer 1 channel • 16-bit PPG timer 1 channel • Waveform sequencer including a 16-bit timer equipped with a buffer and a compare clear function LIN-UART • Full duplex double buffer • Capable of clock-synchronous serial data transfer and clock-asynchronous serial data transfer External interrupt 10 channels • Interrupt by edge detection rising edge, falling edge, and both edges can be selected • Can be used to wake up the device from different low power consumption standby modes 8/10-bit A/D converter 8 channels • 8-bit and 10-bit resolution can be chosen. Low power consumption standby modes • Stop mode • Sleep mode • Watch mode • Time-base timer mode I/O port Clock Timing 33 Source Clock/Machine Clock 35 External Reset 37 Power-on Reset 37 Peripheral Input Timing 38 LIN-UART Timing 39 Low-voltage Detection 44 I2C Timing 46 UART/SIO, Serial I/O Timing 49 MPG Input Timing 50 A/D Converter 50 A/D Converter Electrical Characteristics 50 Notes on Using the A/D Converter 51 Definitions of A/D Converter Terms 52 Flash Memory Write/Erase Characteristics 55 Sample Characteristics 56 Mask Options 61 Ordering Information 62 Package Dimension Page 3 of 66 MB95330H Series Product Line-up MB95F332H MB95F333H MB95F334H MB95F332K MB95F333K MB95F334K Parameter Type Flash memory product Clock supervisor counter It supervises the main clock oscillation. Program ROM capacity 8 Kbyte 12 Kbyte 20 Kbyte 8 Kbyte 12 Kbyte RAM capacity 240 bytes 496 bytes 1008 bytes 240 bytes 496 bytes Low-voltage detection reset Reset input Dedicated Selected by software CPU functions Number of basic instructions Instruction bit length Instruction length Data bit length Minimum instruction execution time Interrupt processing time 136 8 bits 1 to 3 bytes 1, 8 and 16 bits ns with machine clock = MHz µs with machine clock = MHz General-purpose I/O I/O ports Max 28 CMOS I/O 25 N-ch open drain 3 I/O ports Max 29 CMOS I/O 25 N-ch open drain 4 Time-base timer Interrupt cycle ms to s when external clock = 4 MHz Hardware/software watchdog timer Reset generation cycle Main oscillation clock at 10 MHz 105 ms Min The sub-CR clock can be used as the source clock of hardware watchdog timer. Wild register It can be used to replace three bytes of data. LIN-UART Ordering Information MB95F332HPMC-G-SNE2 MB95F332KPMC-G-SNE2 MB95F333HPMC-G-SNE2 MB95F333KPMC-G-SNE2 MB95F334HPMC-G-SNE2 MB95F334KPMC-G-SNE2 MB95F332HP-G-SH-SNE2 MB95F332KP-G-SH-SNE2 MB95F333HP-G-SH-SNE2 MB95F333KP-G-SH-SNE2 MB95F334HP-G-SH-SNE2 MB95F334KP-G-SH-SNE2 MB95F332HWQN-G-SNE1 MB95F332KWQN-G-SNE1 MB95F333HWQN-G-SNE1 MB95F333KWQN-G-SNE1 MB95F334HWQN-G-SNE1 MB95F334KWQN-G-SNE1 32-pin plastic LQFP FPT-32P-M30 32-pin plastic SH-DIP-32P-M06 32-pin plastic QFN LCC-32P-M19 Package MB95330H Series Page 61 of 66 Package Dimension 32-pin plastic LQFP MB95330H Series Lead pitch Package width x package length Lead shape Sealing method Mounting height mm x mm Gullwing Plastic mold mm MAX FPT-32P-M30 32-pin plastic LQFP FPT-32P-M30 9.00±0.20 .354±.008 SQ * 7.00±0.10 .276±.004 SQ Note 1 * These dimensions do not include resin protrusion. Note 2 Pins width and pins thickness include plating thickness. Note 3 Pins width do not include tie bar cutting remainder. INDEX Details of "A" part MAX Mounting height MAX C 2009 FUJITSU MICROELECTRONICS LIMITED F32051S-c-1-1 Dimensions in mm inches . Note The values in parentheses are reference values. Page 62 of 66 32-pin plastic SH-DIP MB95330H Series Lead pitch Low space Sealing method mm Plastic mold DIP-32P-M06 32-pin plastic SH-DIP-32P-M06 INDEX Note 1 * These dimensions do not include resin protrusion. Note 2 Pins width and pins thickness include plating thickness. MAX. C 2003-2008 FUJITSU MICROELECTRONICS LIMITED D32018S-c-1-2 MIN. 0~15° Dimensions in mm inches . Note The values in parentheses are reference values |
More datasheets: HT-11-14 | HT-14-14S | HT-15-38 | HT-16-38 | 74F113PC | AT17F16A-30JC | AT17F16A-30JI | A000062 | MB95F334KP-G-SH-SNE2 | MB95F334KPMC-G-SNE2 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MB95F333KPMC-G-SNE2 Datasheet file may be downloaded here without warranties.