MB89191PF-G-441-EF-RE1

MB89191PF-G-441-EF-RE1 Datasheet

F2MC-8L MB89190/190A Series

Part	Datasheet
MB89191PF-G-441-EF-RE1	MB89191PF-G-441-EF-RE1 (pdf)

PDF Datasheet Preview
The following document contains information on Cypress products. FUJITSU MICROELECTRONICS DATA SHEET DS07-12512-9E 8-bit Proprietary Microcontroller CMOS F2MC-8L MB89190/190A Series MB89191/193/195/P195/PV190 • OUTLINE The MB89190/190A series microcontrollers contain various resources such as timers, serial interfaces, A/D converters, external interrupts, and remote-control functions, as well as an F2MC-8L CPU core for low-voltage and high-speed operations. These single-chip microcontrollers are suitable for small devices such as remote controllers with compact packages. F2MC is the abbreviation of FUJITSU Flexible Microcontroller. • FEATURES • Minimum execution time µs at MHz VCC = V • F2MC-8L family CPU core • Two timers 8/16-bit timer/counter 20-bit timebase counter • Serial interface 8-bit synchronous serial Selectable transfer direction allows communication with various equipment. • External interrupts Edge detection Selectable edge 3 channels Low-level interrupt Wake-up function 8 channels • A/D converter MB89190A series only 8-bit successive approximation type 8 channels • Built-in remote-control transmitting frequency generator • Low-power consumption modes Stop mode Almost no current consumption occurs because oscillation stops. Sleep mode The current consumption is reduced about 1/3 of that during normal operation because the CPU stops. • Packages SOP-28, SH-DIP-28, and DIP-28 For the information for microcontroller supports, see the following web site. Copyright 2001-2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved MB89190/190A Series • PRODUCT LINEUP Part number Item MB89191 MB89191A MB89191AH MB89193 MB89193A MB89193AH MB89195 MB89195A MB89P195 MB89PV190 MB89P195A MB89PV190A Classification ROM size Mask ROM products 4 K x 8 bits internal mask ROM 8 K x 8 bits internal mask ROM 16 K x 8 bits internal mask ROM One-time product For development and evaluation 16 K x 8 bits internal PROM, to be programmed with generalpurpose EPROM programmer 32 K x 8 bits external ROM RAM size 128 x 8 bits 256 x 8 bits CPU functions The number of basic instructions Instruction bit length Instruction length Data bit length Minimum execution time Interrupt processing time: 136 8 bits 1 to 3 bytes 1, 8, and 16 bits µs at MHz µs at MHz Ports Output port N channel open drain 4 also serves as peripherals for MB89190A series or 6 for MB89190 series I/O port CMOS : 16 also serves as peripherals Specify when ordering masking Specify when ordering masking Fixed P00 to P07 Port pull-up P30 to P37 Selectable by pin resistors P00 to P03 Selectable Not P40 to P45 by pin available None Selectable by pin None None Selectable by pin Not available None Not available Not available Power-on reset 2 • Power-on reset provided • No power-on reset Selectable Provided Provided Provided Selection of oscillation stabilization wait time at MHz 1 3 • 218/FC approx. ms • 216/FC approx. ms • 212/FC approx. ms • 22/FC approx. 0 ms Selectable Fixed to 216/FC Selectable Fixed to Fixed to 216/FC 216/FC Reset pin output 4 • Reset output provided • No reset output Selectable Provided Selectable Provided Oscillation type of clock 1 Crystal and ceramic oscillators Selectable “1” only Selectable “1” only “1” only 1 The oscillation stabilization time is generated by dividing the original clock oscillation. The time described in this item should be used as a rough guideline since the oscillation cycle is unstable immediately after oscillation starts. “FC” indicates the original oscillation frequency. 2 and are provided respectively for the MB89P195 and MB89P195A OTP versions as the standard products. • ORDERING INFORMATION MB89191PF MB89193PF MB89195PF MB89P195-101PF MB89191APF MB89191AHPF MB89193APF MB89193AHPF MB89195APF MB89P195A-201PF MB89191P-SH MB89193P-SH MB89195P-SH MB89191AP-SH MB89191AHP-SH MB89193AP-SH MB89193AHP-SH MB89195AP-SH MB89191P MB89193P MB89195P MB89P195-101P MB89191AP MB89191AHP MB89193AP MB89193AHP MB89195AP MB89P195A-201P MB89PV190-101CF MB89PV190A-201CF Package 28-pin Plastic SOP FPT-28P-M17 28-pin Plastic SH-DIP-28C-M03 28-pin Plastic DIP-28P-M05 48-pin Ceramic MQFP MQP-48C-P01 Remarks DS07-12512-9E MB89190/190A Series • PACKAGE DIMENSION 28-pin plastic SOP FPT-28P-M17 Lead pitch Package width x package length Lead shape mm x mm Gullwing Sealing method Plastic mold Mounting height mm MAX Weight Code Reference g P-SOP28-8.6x17.75-1.27 28-pin plastic SOP FPT-28P-M17 Note 1 1 These dimensions include resin protrusion. Note 2 *2 These dimensions do not include resin protrusion. Note 3 Pins width and pins thickness include plating thickness. Note 4 Pins width do not include tie bar cutting remainder. INDEX C 2002-2008 FUJITSU MICROELECTRONICS LIMITED F28048S-c-3-5 Please confirm the latest Package dimension by following URL. Details of "A" part Mounting height 0~8° Stand off Dimensions in mm inches . Note The values in parentheses are reference values. • ORDERING INFORMATION 37 Changed the ordering information. MB89P195PF-101PF MB89P195-101PF MB89P195APF-201PF MB89P195A-201PF MB89P195P-101P MB89P195-101P MB89P195AP-201P MB89P195A-201P MB89PV190CF MB89PV190-101CF MB89PV190A-201CF The vertical lines marked in the left side of the page show the changes. DS07-12512-9E MEMO MB89190/190A Series DS07-12512-9E MB89190/190A Series FUJITSU MICROELECTRONICS LIMITED Shinjuku Dai-Ichi Seimei Bldg., 7-1, Nishishinjuku 2-chome, Shinjuku-ku, Tokyo 163-0722, Japan Tel +81-3-5322-3347 Fax +81-3-5322-3387 For further information please contact: North and South America FUJITSU MICROELECTRONICS AMERICA, INC. 1250 E. Arques Avenue, M/S 333 Sunnyvale, CA 94085-5401, U.S.A. Tel +1-408-737-5600 Fax +1-408-737-5999 Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE. LTD. 151 Lorong Chuan, #05-08 New Tech Park 556741 Singapore Tel +65-6281-0770 Fax +65-6281-0220 Europe FUJITSU MICROELECTRONICS EUROPE GmbH Pittlerstrasse 47, 63225 Langen, Germany Tel +49-6103-690-0 Fax +49-6103-690-122 FUJITSU MICROELECTRONICS SHANGHAI CO., LTD. Rm. 3102, Bund Center, No.222 Yan An Road E , Shanghai 200002, China Tel +86-21-6146-3688 Fax +86-21-6335-1605 Korea FUJITSU MICROELECTRONICS KOREA LTD. 206 Kosmo Tower Building, 1002 Daechi-Dong, Gangnam-Gu, Seoul 135-280, Republic of Korea Tel +82-2-3484-7100 Fax +82-2-3484-7111 FUJITSU MICROELECTRONICS PACIFIC ASIA LTD. 10/F., World Commerce Centre, 11 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel +852-2377-0226 Fax +852-2376-3269 Specifications are subject to change without notice. For further information please contact each office. All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS device FUJITSU MICROELECTRONICS does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated 1 for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system , or 2 for use requiring extremely high reliability i.e., submersible repeater and artificial satellite . Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Edited Sales Promotion Department

PDF Datasheet Preview

The following document contains information on Cypress products.

FUJITSU MICROELECTRONICS DATA SHEET

DS07-12512-9E
8-bit Proprietary Microcontroller

CMOS

F2MC-8L MB89190/190A Series

MB89191/193/195/P195/PV190
• OUTLINE

The MB89190/190A series microcontrollers contain various resources such as timers, serial interfaces, A/D converters, external interrupts, and remote-control functions, as well as an F2MC*-8L CPU core for low-voltage and high-speed operations. These single-chip microcontrollers are suitable for small devices such as remote controllers with compact packages. * F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
• FEATURES
• Minimum execution time µs at MHz VCC = V
• F2MC-8L family CPU core
• Two timers
8/16-bit timer/counter 20-bit timebase counter
• Serial interface 8-bit synchronous serial Selectable transfer direction allows communication with various equipment.
• External interrupts Edge detection Selectable edge 3 channels Low-level interrupt Wake-up function 8 channels
• A/D converter MB89190A series only 8-bit successive approximation type 8 channels
• Built-in remote-control transmitting frequency generator
• Low-power consumption modes Stop mode Almost no current consumption occurs because oscillation stops. Sleep mode The current consumption is reduced about 1/3 of that during normal operation because the CPU stops.
• Packages SOP-28, SH-DIP-28, and DIP-28

For the information for microcontroller supports, see the following web site.

Copyright 2001-2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved

MB89190/190A Series
• PRODUCT LINEUP

Part number Item

MB89191 MB89191A MB89191AH

MB89193 MB89193A MB89193AH

MB89195 MB89195A

MB89P195 MB89PV190 MB89P195A MB89PV190A

Classification ROM size

Mask ROM products
4 K x 8 bits internal mask ROM
8 K x 8 bits internal mask ROM
16 K x 8 bits internal mask ROM

One-time product

For development and evaluation
16 K x 8 bits internal PROM, to be programmed with generalpurpose EPROM programmer
32 K x 8 bits external ROM

RAM size
128 x 8 bits
256 x 8 bits

CPU functions

The number of basic instructions Instruction bit length Instruction length Data bit length Minimum execution time Interrupt processing time:
136 8 bits 1 to 3 bytes 1, 8, and 16 bits µs at MHz µs at MHz

Ports

Output port N channel open drain 4 also serves as peripherals for MB89190A
series or 6 for MB89190 series

I/O port CMOS :
16 also serves as peripherals
Specify when ordering masking
Specify when ordering masking

Fixed

P00 to P07 Port pull-up P30 to P37

Selectable by pin
resistors P00 to P03 Selectable Not

P40 to P45 by pin
available

None Selectable by pin None

None

Selectable by pin

Not available

None

Not available Not available

Power-on reset 2
• Power-on reset provided
• No power-on reset

Selectable

Provided

Provided

Provided

Selection of oscillation stabilization wait time at MHz *1 3
• 218/FC approx. ms
• 216/FC approx. ms
• 212/FC approx. ms
• 22/FC approx. 0 ms

Selectable

Fixed to 216/FC

Selectable

Fixed to Fixed to
216/FC
216/FC

Reset pin output 4
• Reset output provided
• No reset output

Selectable

Provided

Selectable

Provided

Oscillation type of clock
1 Crystal and ceramic oscillators

Selectable
“1” only

Selectable
“1” only “1” only
*1 The oscillation stabilization time is generated by dividing the original clock oscillation. The time described in this item should be used as a rough guideline since the oscillation cycle is unstable immediately after oscillation starts. “FC” indicates the original oscillation frequency.
*2 and are provided respectively for the MB89P195 and MB89P195A OTP versions as the standard products.
• ORDERING INFORMATION

MB89191PF MB89193PF MB89195PF MB89P195-101PF MB89191APF MB89191AHPF MB89193APF MB89193AHPF MB89195APF MB89P195A-201PF

MB89191P-SH MB89193P-SH MB89195P-SH MB89191AP-SH MB89191AHP-SH MB89193AP-SH MB89193AHP-SH MB89195AP-SH

MB89191P MB89193P MB89195P MB89P195-101P MB89191AP MB89191AHP MB89193AP MB89193AHP MB89195AP MB89P195A-201P

MB89PV190-101CF MB89PV190A-201CF

Package
28-pin Plastic SOP FPT-28P-M17
28-pin Plastic SH-DIP-28C-M03
28-pin Plastic DIP-28P-M05
48-pin Ceramic MQFP MQP-48C-P01

Remarks

DS07-12512-9E

MB89190/190A Series
• PACKAGE DIMENSION
28-pin plastic SOP

FPT-28P-M17

Lead pitch

Package width x package length

Lead shape
mm x mm

Gullwing

Sealing method

Plastic mold

Mounting height
mm MAX

Weight

Code Reference
g P-SOP28-8.6x17.75-1.27
28-pin plastic SOP FPT-28P-M17

Note 1 *1 These dimensions include resin protrusion.

Note 2 *2 These dimensions do not include resin protrusion.

Note 3 Pins width and pins thickness include plating thickness.

Note 4 Pins width do not include tie bar cutting remainder.

INDEX

C 2002-2008 FUJITSU MICROELECTRONICS LIMITED F28048S-c-3-5 Please confirm the latest Package dimension by following URL.

Details of "A" part

Mounting
height
0~8°

Stand off

Dimensions in mm inches . Note The values in parentheses are reference values.
• ORDERING INFORMATION 37
Changed the ordering information. MB89P195PF-101PF MB89P195-101PF MB89P195APF-201PF MB89P195A-201PF MB89P195P-101P MB89P195-101P MB89P195AP-201P MB89P195A-201P MB89PV190CF MB89PV190-101CF MB89PV190A-201CF

The vertical lines marked in the left side of the page show the changes.

DS07-12512-9E

MEMO

MB89190/190A Series

DS07-12512-9E

MB89190/190A Series

FUJITSU MICROELECTRONICS LIMITED

Shinjuku Dai-Ichi Seimei Bldg., 7-1, Nishishinjuku 2-chome, Shinjuku-ku, Tokyo 163-0722, Japan Tel +81-3-5322-3347 Fax +81-3-5322-3387

For further information please contact:

North and South America FUJITSU MICROELECTRONICS AMERICA, INC. 1250 E. Arques Avenue, M/S 333 Sunnyvale, CA 94085-5401, U.S.A. Tel +1-408-737-5600 Fax +1-408-737-5999

Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE. LTD. 151 Lorong Chuan, #05-08 New Tech Park 556741 Singapore Tel +65-6281-0770 Fax +65-6281-0220

Europe FUJITSU MICROELECTRONICS EUROPE GmbH Pittlerstrasse 47, 63225 Langen, Germany Tel +49-6103-690-0 Fax +49-6103-690-122

FUJITSU MICROELECTRONICS SHANGHAI CO., LTD. Rm. 3102, Bund Center, No.222 Yan An Road E , Shanghai 200002, China Tel +86-21-6146-3688 Fax +86-21-6335-1605

Korea FUJITSU MICROELECTRONICS KOREA LTD. 206 Kosmo Tower Building, 1002 Daechi-Dong, Gangnam-Gu, Seoul 135-280, Republic of Korea Tel +82-2-3484-7100 Fax +82-2-3484-7111

FUJITSU MICROELECTRONICS PACIFIC ASIA LTD. 10/F., World Commerce Centre, 11 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel +852-2377-0226 Fax +852-2376-3269

Specifications are subject to change without notice. For further information please contact each office.
All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS device FUJITSU MICROELECTRONICS does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated 1 for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system , or 2 for use requiring extremely high reliability i.e., submersible repeater and artificial satellite . Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners.

Edited Sales Promotion Department

More datasheets: KSH221J 50 LFS | KSH451J 50 LFS | 5571303203F | 2271-12-001 | 2274-12-021 | 2274-05-021 | 2271-05-001 | FJX4008RTF | DM7474N | ASMT-CW20

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MB89191PF-G-441-EF-RE1 Datasheet file may be downloaded here without warranties.

Datasheet ID: MB89191PF-G-441-EF-RE1 508294