IW-SMG2SMT-EX

IW-SMG2SMT-EX Datasheet


Connect One’s high-level AT+i API eliminates the need to add WiFi drivers, security and networking protocols and tasks to the host application. The AT+i SerialNET operating mode offers a true plug-and-play mode that eliminates any changes to the host application. Nano WiReach SMT G2 firmware the IP stack and Internet configuration parameters are stored in an external FLASH memory. The EVMB evaluation kit, together with the EVM-iW-SMG2SMT-OB daughter board provides an easy environment for testing the Nano WiReach SMT G2 prior to designing it into your product.

Part Datasheet
IW-SMG2SMT-EX IW-SMG2SMT-EX IW-SMG2SMT-EX (pdf)
Related Parts Information
IW-SMG2SMT-OB IW-SMG2SMT-OB IW-SMG2SMT-OB
PDF Datasheet Preview
Datasheet

Nano WiReach SMT-G2

Version

Connect One Ltd. 20 Atir Yeda Street, Kfar Saba 44643, Israel | Phone +972-9-766-0456 | Fax +972-9-766-0461 Email |

Nano WiReach SMT G2

Information provided by Connect One Ltd. is believed to be accurate and reliable. However, Connect One Ltd. assumes no responsibility for its use, nor any infringement of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent rights of Connect One Ltd. other than for circuitry embodied in Connect One’s products. Connect One Ltd. reserves the right to change circuitry at any time without notice. This document is subject to change without notice. The software described in this document is furnished under a license agreement and may be used or copied only in accordance with the terms of such a license agreement. It is forbidden by law to copy the software on any medium except as specifically allowed in the license agreement. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including but not limited to photocopying, recording, transmitting via fax and/or modem devices, scanning, and/or information storage and retrieval systems for any purpose without the express written consent of Connect One. WARNING THE Nano WiReach SMT G2 IS AN RF MODULE INTENDED FOR EMBEDDING IN A HOST DEVICE. LOCAL RELEVANT RF REGULATIONS SUCH AS ALLOWED FREQUENCIES AND USAGE IN COMMERCIAL FLIGHTS MUST BE OBSERVED. SAFETY INSTRUCTIONS MUST BE INCLUDED IN THE MANUALS OF THE HOST DEVICE. CONNECT ONE ASSUMES NO LIABILITY FOR CUSTOMER FAILURE TO COMPLY WITH THESE PRECAUTIONS.
" Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e.i.r.p. is not more than that necessary for successful communication." " Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal ou inférieur approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente p.i.r.e. ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante." " This radio transmitter SM2144N2-BIO has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device." " Le présent émetteur radio SM2144N2-BIO a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur." " This device complies with Industry Canada license-exempt RSS standard s . Operation is subject to the following two conditions 1 this device may not cause interference, and 2 this device must accept any interference, including interference that may cause undesired operation of the device." " Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes 1 l'appareil ne doit pas produire de brouillage, et 2 l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, si le brouillage est susceptible d'en compromettre le fonctionnement." Antennas Air Wave EA-79F Tekfun C. M04-SR YC Communication Q24-24W Pulse W1030 . Maximum Gain all 2dBi.

Nano WiReach SMT G2
iChip, Nano WiReach SMT G2, IP Communication Controller, SerialNET, AT+i and Connect One are trademarks of Connect One Ltd. Copyright 2014 Connect One Ltd. All rights reserved.

Nano WiReach SMT G2

Table of Contents
2 General Description 3 Hardware 4 Performance Specifications 5 Internet 6 Security Protocols 7 Application Program Interface 8 Wireless Specifications 9 Recommended 10 Certification 11 Installation Requirements 1 Security 2 Protocols 3 Additional Typical AT+i Command Set Layout and Pin 1 Layout 2 Pin Functional 1 Serial 2 SPI 3 USB Device Interface 4 RMII Interface 5 USB Host

Nano WiReach SMT G2

Electrical Specifications 1 Absolute Maximum 2 DC Operating 3 AC Operating Characteristics 4 Transmit Specification 5 Receive 6 On Board Antenna

Mechanical PCB Footprint Design
1 Host PCB Footprint 2 Antenna Clearance Evaluation Ordering Appendix A - Internet Protocol Appendix B AT+I Configuration Examples

Automatically connect to a specific Access Create an Access Point to allow connection from mobile devices LAN WiFi switch mode - merges Ethernet station s with WiFi client s into one logical subnet...25 Appendix C Soldering Profile

Nano WiReach SMT G2

Version

Date May 14th 2014 May 21st 2014 July 7th 2014

July 31, 2014

Oct 14 2014 April 24th 2015

Description Initial preliminary version Adding AT+i commands examples Updating security features Typo fix Updating certifications Updating evaluation platform and drying instruction

Nano WiReach SMT G2

Introduction
2 General Description

Nano WiReach SMT G2 is a secure serial-to-Wireless-LAN device module that can perform as a WLAN client or Access Point to connect serial devices to 802.11b/g/n Wireless LANs. It includes the iChip CO2144 IP Communication Controller chip and Broadcom BCM43362 WiFi chipset. It is packaged in RoHS-compliant ultra-slim form factor and uses an industry standard pin-out. The Nano WiReach SMT G2 can also be interfaced to a 10/100BaseT wired LAN and a USB cellular modem with some external components and glue logic.

Nano WiReach SMT G2 offers and supports large variety of features which among them:
• Ten simultaneous TCP/UDP sockets
• Two listening sockets
• Webserver with two websites
• SMTP and POP3 clients
• DHCP client/server
• POP3 SMTP client with MIME attachment
• client
• TELNET client
• SerialNET mode for serial to IP bridging
• Gateway between a local network on it’s LAN/WLAN interfaces and a WAN on any of
it’s other interfaces
• Switch between it’s WLAN interface and the Ethernet interface when acting as a WLAN
access point
• An Ethernet to WiFi bridge to connect an ETH client to a WiFi network cable
replacement
• Security gap between the application and the network

Nano WiReach SMT G2 supports the SSL3/TLS1 protocol for secure sockets, and secure web server. On the WLAN interface it supports WEP, WPA and WPA2 WiFi encryption.

Nano WiReach SMT G2 minimizes the need to redesign the host device hardware. It features a standard economical SMT footprint providing for low-cost placement on a host PCB with provisions for an on-board or external antenna. Minimal or no software configuration is needed for Nano WiReach SMT G2 to access the Wireless LAN.

Nano WiReach SMT G2

Connect One’s high-level AT+i API eliminates the need to add WiFi drivers, security and networking protocols and tasks to the host application. The AT+i SerialNET operating mode offers a true plug-and-play mode that eliminates any changes to the host application. Nano WiReach SMT G2 firmware the IP stack and Internet configuration parameters are stored in an external FLASH memory. The EVMB evaluation kit, together with the EVM-iW-SMG2SMT-OB daughter board provides an easy environment for testing the Nano WiReach SMT G2 prior to designing it into your product.

Nano WiReach SMT G2
3 Hardware Description

Size:

Core CPU:
32-bit RISC ARM7TDMI, Low-leakage, micron, at 48MHz

Operating Voltage:
+3.3V+/-10%

Operating Humidity Operating Temperature Range:
90% maximum non-condensing -30°C to +85°C

Power Consumption max :
-22°F to 185°F Transmit Receive 130mA

Antenna:

On-Board or U.FL RF Connector

Connection Host Interface:
44 SMT pads Serial, SPI, USB Device

A/D Input

Cellular Modem Interface 10/100 Base T LAN Interface:

USB Host RMII w/ext. PHY
4 Performance Specifications

Host Data Rate:
Ordering Information

Part Number iW-SMG2SMT-EX iW-SMG2SMT-OB

Description Nano WiReach SMT-G2 module, Surface Mounting, External Antenna Nano WiReach SMT-G2 module, Surface Mounting, On Board Antenna

Nano WiReach SMT G2

Appendix A - Internet Protocol Compliance

Nano WiReach SMT G2 complies with the Internet standards listed in the following table

RFC 768 RFC 791 RFC 792 RFC 793 RFC 821 RFC 822 RFC 826 RFC 959 RFC 854 RFC 857 RFC 858 RFC 1034 RFC 1035 RFC 1073 RFC 1091 RFC 1321 RFC 1939 RFC 1957 RFC 2030

RFC 2045

RFC 2046 RFC 2047 RFC 2048 RFC 2049 RFC 2068 RFC 2131 RFC 2132 RFC 2228 RFC 2246

User datagram protocol UDP Internet protocol IP ICMP Internet control message protocol Transmission control protocol TCP Simple mail transfer protocol SMTP Standard for the format of ARPA Internet text messages Ethernet address resolution protocol ARP File transfer protocol TELNET protocol specification Telnet ECHO option Telnet suppress go-ahead option Domain names DNS - concepts and facilities Domain names DNS - implementation and specification Telnet window size option Telnet terminal type option MD5 message digest algorithm Post office protocol - version 3 POP3 Some observations on the implementations of the post office protocol POP3 Simple network time protocol SNTP Multipurpose Internet mail extensions MIME part one internet message body format MIME part two media types MIME part three message header extensions for non-ASCII text MIME part four registration procedures MIME part five conformance criteria and examples Hypertext transfer protocol Dynamic host configuration protocol DHCP options only relevant parts security extensions The TLS protocol version

Nano WiReach SMT G2

Appendix B AT+I Configuration Examples

Automatically connect to a specific Access Point:

AT+iFD
restore to factory defaults

AT+iHIF=1
set the serial interface to RS232

AT+iBDRF=9
fix baud rate to 115200 after power cycle

AT+iRP20
list visible networks

AT+iWLSI=My_WiFi

AT+iWST0=4

WPA2 security

AT+iWPP0=<WPA2 passphrase>

AT+iAWS=1
enable website upon reboot

AT+iDOWN
reboot to apply settings

Create an Access Point to allow connection from mobile devices:

AT+iFD
restore to factory defaults

AT+iHIF=1
set the serial interface to RS232

AT+iBDRF=9
fix baud rate to 115200 after power cycle

AT+iWLSI=My_AP

AT+iDIP=10.0.0.1

IP address

AT+iDPSZ=8

Enable internal DHCP server, up to 8 clients
More datasheets: CY8C21434-24LCXIT | CY8C21434-24LCXI | BZ-AOB5 | USO9ML2DR-2 | HMS_462_CTP | HMS_462_RTP | AP1013AS | 6394 | DN-19KEY-1U-SW | 825802B05300


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived IW-SMG2SMT-EX Datasheet file may be downloaded here without warranties.

Datasheet ID: IW-SMG2SMT-EX 506720