Connect One’s iW-ANT2-BL:
Part | Datasheet |
---|---|
![]() |
IW-SMG2N1 (pdf) |
PDF Datasheet Preview |
---|
Datasheet Nano WiReach G2 N1 Version Connect One Ltd. 20 Atir Yeda Street, Kfar Saba 44643, Israel | Phone +972-9-766-0456 | Fax +972-9-766-0461 Email | Nano WiReach G2 N1 Information provided by Connect One Ltd. is believed to be accurate and reliable. However, Connect One Ltd. assumes no responsibility for its use, nor any infringement of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent rights of Connect One Ltd. other than for circuitry embodied in Connect One’s products. Connect One Ltd. reserves the right to change circuitry at any time without notice. This document is subject to change without notice. The software described in this document is furnished under a license agreement and may be used or copied only in accordance with the terms of such a license agreement. It is forbidden by law to copy the software on any medium except as specifically allowed in the license agreement. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including but not limited to photocopying, recording, transmitting via fax and/or modem devices, scanning, and/or information storage and retrieval systems for any purpose without the express written consent of Connect One. WARNING THE Nano WiReach G2 N1 IS AN RF MODULE INTENDED FOR EMBEDDING IN A HOST DEVICE. LOCAL RELEVANT RF REGULATIONS SUCH AS ALLOWED FREQUENCIES AND USAGE IN COMMERCIAL FLIGHTS MUST BE OBSERVED. SAFETY INSTRUCTIONS MUST BE INCLUDED IN THE MANUALS OF THE HOST DEVICE. CONNECT ONE ASSUMES NO LIABILITY FOR CUSTOMER FAILURE TO COMPLY WITH THESE PRECAUTIONS. " Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e.i.r.p. is not more than that necessary for successful communication." " Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal ou inférieur approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente p.i.r.e. ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante." " This radio transmitter SM2144N2-BIO has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device." " Le présent émetteur radio SM2144N2-BIO a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur." " This device complies with Industry Canada license-exempt RSS standard s . Operation is subject to the following two conditions 1 this device may not cause interference, and 2 this device must accept any interference, including interference that may cause undesired operation of the device." " Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes 1 l'appareil ne doit pas produire de brouillage, et 2 l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, si le brouillage est susceptible d'en compromettre le fonctionnement." Antennas Air Wave EA-79F Tekfun C. M04-SR YC Communication Q24-24W Pulse W1030 . Maximum Gain all 2dBi. Nano WiReach G2 N1 iChip, Nano WiReach G2 N1, IP Communication Controller, SerialNET, AT+i and Connect One are trademarks of Connect One Ltd. Copyright 2014 Connect One Ltd. All rights reserved. Nano WiReach G2 N1 Table of Contents 2 General Description 3 Hardware 4 Performance Specifications 5 Internet 6 Security Protocols 7 Application Program Interface 8 Wireless Specifications 9 Recommended 10 Certification 11 Installation Requirements 1 Security 2 Protocols 3 Additional Typical AT+i Command Set Layout and Pin 1 Layout 2 Pin Functional 1 Serial 2 SPI 3 USB Device Interface 4 RMII Interface Electrical Specifications Nano WiReach G2 N1 1 Absolute Maximum 2 DC Operating 3 AC Operating Characteristics 4 Transmit Specification 5 Receive Mechanical Nano WiReach G2 N1 Mounting Evaluation Ordering Appendix A - Internet Protocol Appendix B AT+I Configuration Examples Automatically connect to a specific Access Create an Access Point to allow connection from mobile devices LAN WiFi switch mode - merges Ethernet station s with WiFi client s into one logical subnet...24 Nano WiReach G2 N1 Version Date May 22nd 2014 June 16th 2014 July 7th 2014 September 16, 2014 November 24, 2014 Description Initial preliminary version Adding module image Security support update Certification update, mechanical drawings, appendix B update RMII pin out descriptions Nano WiReach G2 N1 Introduction 2 General Description Nano WiReach G2 N1 is a secure serial-to-Wireless-LAN device module that can perform as a WLAN client or Access Point to connect serial devices to 802.11b/g/n Wireless LANs. It includes the iChip CO2144 IP Communication Controller chip and Broadcom BCM43362 WiFi chipset. It is packaged 33.76X18mm RoHS-compliant low profile module with 30 PIN Board to Board connector and UFL connector for external antenna. Nano WiReach G2 N1 offers and supports large variety of features which among them: • Ten simultaneous TCP/UDP sockets • Two listening sockets • Webserver with two websites • SMTP and POP3 clients • DHCP client/server • POP3 SMTP client with MIME attachment • client • TELNET client • SerialNET mode for serial to IP bridging • Gateway between a local network on it’s LAN/WLAN interfaces and a WAN on any of it’s other interfaces • Switch between it’s WLAN interface and the Ethernet interface when acting as a WLAN access point • An Ethernet to WiFi bridge to connect an ETH client to a WiFi network cable replacement • Security gap between the application and the network Nano WiReach G2 N1 supports the SSL3/TLS1 protocol for secure sockets, and secure web server. On the WLAN interface it supports WEP, WPA and WPA2 WiFi encryption. Nano WiReach G2 N1 minimizes the need to redesign the host device hardware. It easily inserts into a 30 pin Board to Board connector host PCB and connects to an external antenna. Minimal or no software configuration is needed for Nano WiReach G2 N1 to access the Wireless LAN. Connect One’s high-level AT+i API eliminates the need to add WiFi drivers, security and networking protocols and tasks to the host application. The AT+i SerialNET operating mode offers a true plug-and-play mode that eliminates any changes to the host application. Nano WiReach G2 N1 Nano WiReach G2 N1 firmware the IP stack and Internet configuration parameters are stored in an external FLASH memory. The II-EVB-363-G2-N1 evaluation board provides an easy environment for testing the Nano WiReach G2 N1 prior to designing it into your product. Nano WiReach G2 N1 3 Hardware Description Size: Core CPU: 32-bit RISC ARM7TDMI, Low-leakage, micron, at 48MHz Operating Voltage: +3.3V+/-10% Operating Humidity Operating Temperature Range: 90% maximum non-condensing -30°C to +85°C Power Consumption max : -22°F to 185°F Transmit Receive 130mA Antenna: U.FL RF Connector Connection Host Interface: Low profile 30 pin Board to Board connector Serial, SPI, USB Device A/D Input 10/100 Base T LAN Interface: RMII w/ext. PHY 4 Performance Specifications Host Data Rate: Up to 3Mbps in serial mode Ordering Information Part Number iW-SMG2N1 Description Nano WiReach G2 N1 WiFi Module Nano WiReach G2 N1 Appendix A - Internet Protocol Compliance Nano WiReach G2 N1 complies with the Internet standards listed in the following table RFC 768 RFC 791 RFC 792 RFC 793 RFC 821 RFC 822 RFC 826 RFC 959 RFC 854 RFC 857 RFC 858 RFC 1034 RFC 1035 RFC 1073 RFC 1091 RFC 1321 RFC 1939 RFC 1957 RFC 2030 RFC 2045 RFC 2046 RFC 2047 RFC 2048 RFC 2049 RFC 2068 RFC 2131 RFC 2132 RFC 2228 RFC 2246 User datagram protocol UDP Internet protocol IP ICMP Internet control message protocol Transmission control protocol TCP Simple mail transfer protocol SMTP Standard for the format of ARPA Internet text messages Ethernet address resolution protocol ARP File transfer protocol TELNET protocol specification Telnet ECHO option Telnet suppress go-ahead option Domain names DNS - concepts and facilities Domain names DNS - implementation and specification Telnet window size option Telnet terminal type option MD5 message digest algorithm Post office protocol - version 3 POP3 Some observations on the implementations of the post office protocol POP3 Simple network time protocol SNTP Multipurpose Internet mail extensions MIME part one internet message body format MIME part two media types MIME part three message header extensions for non-ASCII text MIME part four registration procedures MIME part five conformance criteria and examples Hypertext transfer protocol Dynamic host configuration protocol DHCP options only relevant parts security extensions The TLS protocol version Nano WiReach G2 N1 Appendix B AT+I Configuration Examples Automatically connect to a specific Access Point: AT+iFD restore to factory defaults AT+iHIF=1 set the serial interface to RS232 AT+iBDRF=9 fix baud rate to 115200 after power cycle AT+iRP20 list visible networks AT+iWLSI=My_WiFi AT+iWST0=4 WPA2 security AT+iWPP0=<WPA2 passphrase> AT+iAWS=1 enable website upon reboot AT+iDOWN reboot to apply settings Create an Access Point to allow connection from mobile devices: AT+iFD restore to factory defaults AT+iHIF=1 set the serial interface to RS232 AT+iBDRF=9 fix baud rate to 115200 after power cycle AT+iWLSI=My_AP AT+iDIP=10.0.0.1 IP address AT+iDPSZ=8 Enable internal DHCP server, up to 8 clients |
More datasheets: B32591C3473J008 | B32591C6103J008 | B32592C6104J008 | FDD6680A | 8P15-N001 | 8P37-N001 | 8P09-N001 | 8P25-N001 | 410-346-20 | 96RC-AFM700-AD |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived IW-SMG2N1 Datasheet file may be downloaded here without warranties.