IEEE 802.11b/g/n for iWL-NETBOX-N IEEE 802.11b/g for iWL-NETBOX-G Europe 2.412-2.472GHz USA 2.412-2.462GHz Default Japan Europe 13 channels USA 11 channels Japan 14 channels
Part | Datasheet |
---|---|
![]() |
IWL-NETBOX-N (pdf) |
Related Parts | Information |
---|---|
![]() |
IWL-NETBOX-G |
PDF Datasheet Preview |
---|
Datasheet iChipNet Box Version Connect One Ltd. 20 Atir Yeda Street, Kfar Saba 44643, Israel | Phone +972-9-766-0456 | Fax +972-9-766-0461 Email | iChipNet-Box Information provided by Connect One Ltd. is believed to be accurate and reliable. However, Connect One Ltd. assumes no responsibility for its use, nor any infringement of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent rights of Connect One Ltd. other than for circuitry embodied in Connect One’s products. Connect One Ltd. reserves the right to change circuitry at any time without notice. This document is subject to change without notice. The software described in this document is furnished under a license agreement and may be used or copied only in accordance with the terms of such a license agreement. It is forbidden by law to copy the software on any medium except as specifically allowed in the license agreement. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including but not limited to photocopying, recording, transmitting via fax and/or modem devices, scanning, and/or information storage and retrieval systems for any purpose without the express written consent of Connect One. WARNING THE iChipNet Box IS AN RF Device INTENDED FOR EXTERNAL USAGE OR EMBEDDING IN A HOST DEVICE. LOCAL RELEVANT RF REGULATIONS SUCH AS ALLOWED FREQUENCIES AND USAGE IN COMMERCIAL FLIGHTS MUST BE OBSERVED. SAFETY INSTRUCTIONS MUST BE INCLUDED IN THE MANUALS OF THE HOST DEVICE. CONNECT ONE ASSUMES NO LIABILITY FOR CUSTOMER FAILURE TO COMPLY WITH THESE PRECAUTIONS. " Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e.i.r.p. is not more than that necessary for successful communication." " Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal ou inférieur approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente p.i.r.e. ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante." " This radio transmitter SM2144N2-BIO has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device." " Le présent émetteur radio SM2144N2-BIO a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur." " This device complies with Industry Canada license-exempt RSS standard s . Operation is subject to the following two conditions 1 this device may not cause interference, and 2 this device must accept any interference, including interference that may cause undesired operation of the device." " Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes 1 l'appareil ne doit pas produire de brouillage, et 2 l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, si le brouillage est susceptible d'en compromettre le fonctionnement." Antennas Air Wave EA-79F Tekfun C. M04-SR YC Communication Q24-24W Pulse W1030 . Maximum Gain all 2dBi. iChipNet-Box iChip, iChipNet Box, IP Communication Controller, SerialNET, AT+i and Connect One are trademarks of Connect One Ltd. Copyright 2014 Connect One Ltd. All rights reserved. iChipNet-Box Table of Contents 1 General Description 2 Hardware 3 Performance Specifications 4 Internet 5 Security Protocols 6 Application Program Interface 7 Wireless Specifications 8 Certification 1 Security 2 Protocols 3 Additional Typical AT+i Command Set Dimension and Connection RS232 Pin Description Power Electrical Specifications 1 Absolute Maximum 2 DC Operating 3 Transmit Specification 4 Receive Ordering Information Appendix A - Internet Protocol Appendix B AT+I Configuration Examples iChipNet-Box Automatically connect to a specific Access Create an Access Point to allow connection from mobile devices LAN WiFi switch mode - merges Ethernet station s with WiFi client s into one logical subnet...17 iChipNet-Box Version Date April 21st 2015 April 29th 2015 April 30th 2015 Description Initial preliminary version Updating power consumption Updating reset button functionality iChipNet-Box Introduction 1 General Description iChipNet Box is a secure serial-to-Wireless-LAN device that can perform as a WLAN / LAN client to connect serial devices to 802.11b/g or 802.11b/g/n Wireless LAN or LAN only. Additionally the iChipNet Box can function as an Access Point and router. It includes the iChip CO2144 IP Communication Controller a WiFi baseband and LAN RJ45 connector. It is packaged in a X 25.1mm box with LAN connector, SMA Antenna connector, D-Type RS232 connector and a DC power inlet. The default configuration of the iChipNet Box is Serial to WiFi. Please refer to Appendix B for additional configuration options iChipNet Box offers and supports large variety of features which among them: • Ten simultaneous TCP/UDP sockets • Two listening sockets • Webserver with two websites • SMTP and POP3 clients • DHCP client/server • POP3 SMTP client with MIME attachment • client • TELNET client • SerialNET mode for serial to IP bridging • Gateway between a local network on its LAN/WLAN interfaces and a WAN on any of its other interfaces • Switch between its WLAN interface and the Ethernet interface when acting as a WLAN access point • An Ethernet to WiFi bridge to connect an ETH client to a WiFi network cable replacement • Security gap between the application and the network iChipNet Box supports the SSL3/TLS1 protocol for secure sockets, and secure web server. On the WLAN interface it supports WEP, WPA and WPA2 WiFi encryption. Connect One’s high-level AT+i API eliminates the need to add WiFi drivers, security and networking protocols and tasks to the host application. The AT+i SerialNET operating mode offers a true plug-and-play mode that eliminates any changes to the host application. iChipNet-Box iChipNet Box with its internal IP stack and Internet configuration parameters are stored in a FLASH memory. 2 Hardware Description Size: X 65.3X 25.1mm box Core CPU: 32-bit RISC ARM7TDMI, Operating Voltage: Low-leakage, micron, at 48MHz 6-24VDC Operating Humidity Operating Temperature Range: 90% maximum non-condensing +5°C to +50°C 41°F to 122°F Antenna Ethernet Connection RP-SMA antenna gain 2dBi SMA RF Connector RJ45 10/100 Base T LAN Host Interface: Serial, RS232 3 Performance Specifications Host Data Rate: Up to 1Mbps in serial mode Serial Data Format AT+i mode Asynchronous character binary 8 data bits no parity 1 stop bit SerialNET mode: Asynchronous character binary 7 or 8 data bits odd, even, or no parity 1 stop bit Power supply could be ordered from Connect One, Please refer to the ordering instruction Reset Button functionality The reset button is connected to the Msel signal in the iChip. Pressing the Reset button have several functionalities which are being activated upon pressing duration and power state. Please refer to Connect One’s AT+i manual for further explanation of the Msel signal. 1 During power up A Press less than 2 seconds iChipNet Box goes to auto baud rate and auto host interface. B Press more than 4 seconds iChipNet Box goes to Boot-Rom. In this case user can program F/W by using the iChipConfig software. iChipConfig could be downloaded from Connect One website 2 During normal operation A Press more than 5 second and less than 30 seconds - iChipNet Box goes to rescues mode. In Rescue mode, iChip performs the following operations a. If in SerialNET mode iChipNet Box exits SerialNET mode SNMD is permanently changed to 0 b. If serial baud rate in BDRF or BDRD is set to a fixed value iChipNet Box forces auto baud rate detection. BDRF/BDRD retain their values and will be used again upon the next power-up iChipNet-Box c. If Always Online mode is defined TUP=2 , or Automatic Router Start is enabled ARS=1 iChipNet Box bypasses this mode, which means that the iChipNet Box does not attempt to go online until the next software or hardware reset d. If LAN-to-WiFi Bridge mode is enabled and the BRM parameter contains a non-zero value iChipNet Box disables Bridge mode and permanently assigns BRM=0. e. If the Host Interface parameter HIF is set to a fixed interface, it is forced to auto host interface detection mode HIF=0 B Press more than 30 seconds - iChipNet Box re-install parameter profile. Electrical Specifications 1 Absolute Maximum Ratings Parameter Max power consumption Operating Temperature Storage Temperature b/g iWL-NETBOX-G 1.8W to b/g/n iWL-NETBOX-N 2W to 2 DC Operating Characteristics Parameter Vin Radio Frequency Range Min 6 Max 24 Units Volts GHz Remark US Default EU JP 3 Transmit Specification Item Condition Transmit Power Levels 802.11b 802.11g 802.11n 802.11b/g/n 802.11b/g Unit iWL-NETBOX-N iWL-NETBOX-G Min Typ Max Min Typ Max Ordering Information Part Number iWL-NETBOX-G iWL-NETBOX-N Accessories CABLE-DB9-F/M-G CABLE-DB9-F/F-G CABLE-DB9-F/M+P-G W-TR-110/9-P5-G W-TR-220/9-P5-G CABLE-RJ45 Description iChipNet Box supporting b/g iChipNet Box supporting b/g/n Serial Cable with DB9 connector Female / Male Serial Cable with DB9 connector Female / Female Serial Cable with DB9 connector Female / Male + power cable 110VAC to 9VDC power supply 220VAC to 9VDC power supply LAN Cable iChipNet-Box Appendix A - Internet Protocol Compliance iChipNet Box complies with the Internet standards listed in the following table RFC 768 RFC 791 RFC 792 RFC 793 RFC 821 RFC 822 RFC 826 RFC 959 RFC 854 RFC 857 RFC 858 RFC 1034 RFC 1035 RFC 1073 RFC 1091 RFC 1321 RFC 1939 RFC 1957 RFC 2030 RFC 2045 RFC 2046 RFC 2047 RFC 2048 RFC 2049 RFC 2068 RFC 2131 RFC 2132 RFC 2228 RFC 2246 User datagram protocol UDP Internet protocol IP ICMP Internet control message protocol Transmission control protocol TCP Simple mail transfer protocol SMTP Standard for the format of ARPA Internet text messages Ethernet address resolution protocol ARP File transfer protocol TELNET protocol specification Telnet ECHO option Telnet suppress go-ahead option Domain names DNS - concepts and facilities Domain names DNS - implementation and specification Telnet window size option Telnet terminal type option MD5 message digest algorithm Post office protocol - version 3 POP3 Some observations on the implementations of the post office protocol POP3 Simple network time protocol SNTP Multipurpose Internet mail extensions MIME part one internet message body format MIME part two media types MIME part three message header extensions for non-ASCII text MIME part four registration procedures MIME part five conformance criteria and examples Hypertext transfer protocol Dynamic host configuration protocol DHCP options only relevant parts security extensions The TLS protocol version iChipNet-Box Appendix B AT+I Configuration Examples Automatically connect to a specific Access Point: AT+iFD restore to factory defaults AT+iHIF=1 set the serial interface to RS232 AT+iBDRF=9 fix baud rate to 115200 after power cycle AT+iRP20 list visible networks AT+iWLSI=My_WiFi AT+iWST0=4 WPA2 security AT+iWPP0=<WPA2 passphrase> AT+iAWS=1 enable website upon reboot AT+iDOWN reboot to apply settings Create an Access Point to allow connection from mobile devices: AT+iFD restore to factory defaults AT+iHIF=1 set the serial interface to RS232 AT+iBDRF=9 fix baud rate to 115200 after power cycle AT+iWLSI=My_AP AT+iDIP=10.0.0.1 IP address AT+iDPSZ=8 |
More datasheets: HC1S80F1020AXP | HC1S80F1020AXR | HC1S80F1020AY | HC1S80F1020AYP | FDPF14N30T | FDPF14N30 | ACP-1010MB0-30ZE | ACP-1010BP-30ZE | ACP-1320MB0-30ZE | IWL-NETBOX-G |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived IWL-NETBOX-N Datasheet file may be downloaded here without warranties.