HFBR-4531

HFBR-4531 Datasheet

HFBR-4531/4532/4533/4535 Crimpless Connectors for Plastic Optical Fiber and Versatile Link

Part	Datasheet
HFBR-4531	HFBR-4531 (pdf)

PDF Datasheet Preview
HFBR-4531/4532/4533/4535 Crimpless Connectors for Plastic Optical Fiber and Versatile Link Data Sheet The HFBR-453x series connectors are an enhanced version of the HFBR-4501 and HFBR-4503 low-cost connectors for plastic optical fiber, which are compatible with Avago Technologies’ versatile link series transmitters and receivers. The innovative design uses a simple, snap-together concept which eliminates the need for crimping. This connector not only saves the user labor and tool cost, but reduces the yield loss due to installation error. The HFBR-453x series connectors are available in two styles latching and non-latching. For a duplex connector, two non-latching simplex connectors can be snapped together. The connectors are made of a rugged, flame retardant plastic which is good for industrial and other harsh environments. The HFBR-453x series connectors are for use with Plastic Optical Fiber only. The HFBR-453x Series of connectors are available in three colors black, blue and grey. The ability to select colors to match Transmitters and Receivers makes it easier for the User to differentiate between fiber connections especially when there are a large number. Features • Requires No Crimp Ring or Crimping Tool • Durable Plastic Material UL File #E121562 • Same Low Cost as HFBR-4501/4503 Series Connec- tors • Excellent Retention Force • Symmetry in Nonlatching Connector Gives Simplex/ Duplex Functionality with the Same Part These connectors can be used for any application in which plastic optical fiber is used including: • Industrial Control and Voltage Isolation • Automotive Networks • Proprietary System Interconnects • Gaming Equipment • Medical Equipment • Telecommunications • Datacommunications is a registered trademark of the General Electric Corporation. Termination Guide Step-by-Step Plastic Cable Connectoring Instructions The following step-by-step guide describes how to terminate plastic fiber optic cable. It is ideal for both field and factory installations. Connectors can be easily installed on cable ends with standard tools such as wire strippers and cutters. Finishing the cable is accomplished with the Avago Technologies HFBR-4593 Polishing Kit, consisting of a polishing fixture, 600 grid abrasive paper and 3 mm pink lapping film 3M Company, OC3-14 . The connector can be used immediately after polishing. The following materials are needed for plastic fiber termination: Plastic optical fiber cable Example HFBR-RUD500 Wire cutters or scissors 16 gauge wire stripper Example Ideal Stripmaster type 45-092 HFBR-4593 polishing kit optional Crimpless connectors Step 2 Putting on the Connector Place the connector on each end of the fiber, and slide the connector down until the fiber jacket stops it. The fiber should protrude no less than mm in from the end of the connector. Step 1 Stripping the Fiber The zip cord structure of the duplex cable permits easy separation of the channels. The channels should be separated a minimum of 100 mm 4 in to a maximum of 150 mm 6 in back from the ends to permit connectoring, polishing and cable end flexibility. After cutting the cable to the desired length, strip off approximately 7 mm in of the outer jacket with the 16 gauge wire strippers. To install simplex connectors flip the top half of the connector over and snap it into the ferrule half with your fingers . When the top half latches inside the body of the ferrule half, proper connector-to-cable attachment is achieved. For duplex connector installation place one connector on top of the other, so that the top half of each connector is over the ferrule half of the opposite connector. When using the duplex connector arrangement, the separated duplex cable should be stripped to roughly equal lengths on each cable end. For the non-latching version HFBR-4531 , the same connector is used for simplex and duplex arrangement. No crimping is necessary. The top half of the connector will snap into the ferrule half to secure the fiber. Manually press connectors together in the center of the arrangement. Then latch by pressing on the sides of each connector. As with the simplex version, connectors are secured when top halves latch into the ferrule halves. Step 3 Trimming and Polishing Any fiber in excess of mm in protruding from the connector end should be cut off with wire cutters or scissors. Insert the connector fully into the polishing fixture with the trimmed fiber protruding from the bottom of the fixture. This plastic polishing fixture can be used to polish two simplex connectors simultaneously or one duplex connector. Step 4 Finishing Place the flush connector and polishing fixture on the dull side of the 3 µm pink lapping film and continue to polish the fiber in the same figure eight pattern for approximately 25 strokes. The fiber end should be flat, smooth and clean. Note The four dots on the bottom of the polishing fixture are wear indicators. Replace the polishing fixture when any dot is no longer visible. Press the polishing tool down on the 600 grit abrasive paper. Polish the fiber using a figure eight pattern until the connector is flush with the bottom of the polishing fixture. Wipe the connector and fixture with a clean cloth or tissue. HFBR-4593 Polishing Kit Note Use of the pink lapping film fine polishing step results in approximately 2 dB improvement in coupling performance of either a transmitter-receiver link or a bulkhead/splice over a 600 grit polish alone. This fine polish is comparable to the Avago Technologies factory polish. The fine polishing step may be omitted for short link lengths. Crimpless Connectors Black Blue Grey HFBR-4531/4532/4533/4535 Absolute Maximum Ratings

PDF Datasheet Preview

HFBR-4531/4532/4533/4535 Crimpless Connectors for Plastic Optical Fiber and Versatile Link

Data Sheet

The HFBR-453x series connectors are an enhanced version of the HFBR-4501 and HFBR-4503 low-cost connectors for plastic optical fiber, which are compatible with Avago Technologies’ versatile link series transmitters and receivers. The innovative design uses a simple, snap-together concept which eliminates the need for crimping. This connector not only saves the user labor and tool cost, but reduces the yield loss due to installation error.

The HFBR-453x series connectors are available in two styles latching and non-latching. For a duplex connector, two non-latching simplex connectors can be snapped together. The connectors are made of a rugged, flame retardant plastic which is good for industrial and other harsh environments. The HFBR-453x series connectors are for use with Plastic Optical Fiber only.

The HFBR-453x Series of connectors are available in three colors black, blue and grey. The ability to select colors to match Transmitters and Receivers makes it easier for the User to differentiate between fiber connections especially when there are a large number.

Features
• Requires No Crimp Ring or Crimping Tool
• Durable Plastic Material UL File #E121562
• Same Low Cost as HFBR-4501/4503 Series Connec-
tors
• Excellent Retention Force
• Symmetry in Nonlatching Connector Gives Simplex/

Duplex Functionality with the Same Part

These connectors can be used for any application in which plastic optical fiber is used including:
• Industrial Control and Voltage Isolation
• Automotive Networks
• Proprietary System Interconnects
• Gaming Equipment
• Medical Equipment
• Telecommunications
• Datacommunications
is a registered trademark of the General Electric Corporation.

Termination Guide

Step-by-Step Plastic Cable Connectoring Instructions

The following step-by-step guide describes how to terminate plastic fiber optic cable. It is ideal for both field and factory installations. Connectors can be easily installed on cable ends with standard tools such as wire strippers and cutters.

Finishing the cable is accomplished with the Avago Technologies HFBR-4593 Polishing Kit, consisting of a polishing fixture, 600 grid abrasive paper and 3 mm pink lapping film 3M Company, OC3-14 . The connector can be used immediately after polishing.

The following materials are needed for plastic fiber termination:

Plastic optical fiber cable Example HFBR-RUD500 Wire cutters or scissors 16 gauge wire stripper Example Ideal Stripmaster
type 45-092 HFBR-4593 polishing kit optional Crimpless connectors

Step 2 Putting on the Connector

Place the connector on each end of the fiber, and slide the connector down until the fiber jacket stops it. The fiber should protrude no less than mm in from the end of the connector.

Step 1 Stripping the Fiber

The zip cord structure of the duplex cable permits easy separation of the channels. The channels should be separated a minimum of 100 mm 4 in to a maximum of 150 mm 6 in back from the ends to permit connectoring, polishing and cable end flexibility.

After cutting the cable to the desired length, strip off approximately 7 mm in of the outer jacket with the 16 gauge wire strippers.

To install simplex connectors flip the top half of the connector over and snap it into the ferrule half with your fingers . When the top half latches inside the body of the ferrule half, proper connector-to-cable attachment is achieved.

For duplex connector installation place one connector on top of the other, so that the top half of each connector is over the ferrule half of the opposite connector.

When using the duplex connector arrangement, the separated duplex cable should be stripped to roughly equal lengths on each cable end.

For the non-latching version HFBR-4531 , the same connector is used for simplex and duplex arrangement. No crimping is necessary. The top half of the connector will snap into the ferrule half to secure the fiber.

Manually press connectors together in the center of the arrangement. Then latch by pressing on the sides of each connector. As with the simplex version, connectors are secured when top halves latch into the ferrule halves.

Step 3 Trimming and Polishing

Any fiber in excess of mm in protruding from the connector end should be cut off with wire cutters or scissors.

Insert the connector fully into the polishing fixture with the trimmed fiber protruding from the bottom of the fixture. This plastic polishing fixture can be used to polish two simplex connectors simultaneously or one duplex connector.

Step 4 Finishing

Place the flush connector and polishing fixture on the dull side of the 3 µm pink lapping film and continue to polish the fiber in the same figure eight pattern for approximately 25 strokes. The fiber end should be flat, smooth and clean.

Note The four dots on the bottom of the polishing fixture are wear indicators. Replace the polishing fixture when any dot is no longer visible.

Press the polishing tool down on the 600 grit abrasive paper. Polish the fiber using a figure eight pattern until the connector is flush with the bottom of the polishing fixture. Wipe the connector and fixture with a clean cloth or tissue.

HFBR-4593 Polishing Kit

Note Use of the pink lapping film fine polishing step results in approximately 2 dB improvement in coupling performance of either a transmitter-receiver link or a bulkhead/splice over a 600 grit polish alone. This fine polish is comparable to the Avago Technologies factory polish. The fine polishing step may be omitted for short link lengths.

Crimpless Connectors

Black Blue Grey

HFBR-4531/4532/4533/4535 Absolute Maximum Ratings

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived HFBR-4531 Datasheet file may be downloaded here without warranties.

Datasheet ID: HFBR-4531 520306