AFCT-711XPDZ Multi-rate 1310 nm XFP 10 Gbit/s Optical Transceiver
Part | Datasheet |
---|---|
![]() |
AFCT-711XPDZ (pdf) |
PDF Datasheet Preview |
---|
AFCT-711XPDZ Multi-rate 1310 nm XFP 10 Gbit/s Optical Transceiver Data Sheet • Fibre Channel Switches • Host Bus Adapter Cards • Mass Storage System and Server I/O • Optical Cross Connect Switches - Next generation SONET/SDH ADMs - Core Routers Related Products • AFCT-721XPDZ 10GbE/10GFC 1310nm XFP 10Gbit/s Optical Transceiver • AFBR-720XPDZ 10GbE 850nm XFP 10Gbit/s Optical Transceiver Features • RoHS-6 Compliant • Supports 9.95Gb/s to 11.3Gb/s bit rates • Compliant to XFP MSA • Multi-protocol multi-bitrate - SONET/SDH OC-192/STM-64 rate Gb/s, Telcordia GR-253-CORE SR-1, ITU-T G.691 I64.1 - IEEE 802.3ae 10GBASE-LR for 10GbE, Gb/s - 10GFC 1310 nm Serial PMD, type 1200-SM-LL-L, Gb/s • Uncooled 1310 nm DFB Laser and PIN Photodiode • Compliant XFI 10G Serial electrical interface • LC Duplex optical connector interface conforming to ANSI TIA/EIA604-10 FOCIS 10 • 1.5W typical power dissipation • No Reference Clock required • Superior Thermal and EMI performance to support high port densities • Customizable clip-on heatsink to support a variety of line card environments • -5 to +70 °C case operating temperature range • Support XFI loopback • 2-wire serial management interface provides real time monitors of - Transmitted Optical Power - Received Optical Power - Laser Bias Current - Module Temperature - Supply Voltage • Link Lengths up to 10 km with 9 µm SMF • IEC 60825-1 Class 1/CDRH Class 1 laser eye safe The product offers digital diagnostics using the 2-wire serial interface defined in the XFP MSA. The product provides real time temperature module and laser , supply voltage, laser bias current, laser average output power and received input power. The digital diagnostic interface also adds the ability to disable the transmitter TX_DIS , power down the module, monitor for module faults and monitor for Receiver Loss of Signal RX_LOS . Transmitter disable, interrupt, power down/reset, receiver loss of signal and module not ready are also hard wired pins on the 30-pin right angle connector. Installation The AFCT-711XPDZ is hot-pluggable, allowing the module to be installed while the host system is operating and on-line. The attach heatsink is designed to clip on to the XFP cage without a module present. Upon insertion, the transceiver housing makes initial contact with the host board XFP cage, mitigating potential damage due to Electro-Static Discharge ESD . Once fully inserted into the XFP cage, the top surface of the XFP module makes contact with the heatsink through a cutout in the top of the cage ensuring an effective thermal path for module heat. Functional Description Transmitter Section The transmitter section includes a 1310 nm DFB Distributed Feedback Laser light source, a transmitter driver circuit and a signal conditioner circuit on the TX data inputs. See Figure 1 Optical connection to the transmitter is provided via a LC connector. The optical output is controlled by a custom IC that detects the laser output via the monitor photodiode. This IC provides both dc and AC current drive to the laser to ensure correct modulation, eye diagram and extinction ratio over temperature, supply voltage and operating life. TX_DIS Asserting pin 5, TX_DIS, will disable the transmitter optical output. The transmitter output can also be disabled and monitored via the two-wire serial interface. Eye Safety Circuit Under normal operating conditions laser power will be maintained below Class 1 eye-safety limits. Optical receptacles Analog signal conditioners D/A Electrical connector Heat sink Laser Optical isolator Mon. PIN TOSA PIN ROSA TIA Main housing Figure Transceiver Functional Diagram RF driver CW driver An Evaluation Kit and Reference Designs are available to assist in evaluation of the AFCT-711XPDZ. Please contact your local Field Sales representative for availability and ordering details. Regulatory Compliance The transceiver Regulatory Compliance performance is provided in Table 2 as a figure of merit to assist the designer. The overall equipment design will determine the certification level. Electrostatic Discharge ESD There are two conditions in which immunity to ESD damage is important. Table 2 documents the ESD immunity to both of these conditions. The first condition is static discharge to the transceiver during handling such as when the transceiver is inserted into the transceiver port. To protect the transceiver, it is important to use normal ESD handling precautions including the use of grounded wrist straps, work benches, and floor mats in ESD controlled areas. The ESD sensitivity of the AFCT-711XPDZ is compatible with typical industry production environments. The second condition is static discharge to the exterior of the host equipment chassis after installation. To the extent that the duplex LC optical interface is exposed to the outside of the host equipment chassis, it may be subject to system-level ESD requirements. The ESD performance of the AFCT-711XPDZ exceeds typical industry standards. Immunity The transceivers have a shielded design to provide excellent immunity to radio-frequency electromagnetic fields which may be present in some operating environments. Electromagnetic Interference EMI Most equipment designs using the AFCT-711XPDZ are subject to the requirements of the FCC in the United States, CENELEC EN55022 CISPR 22 in Europe and VCCI in Japan. The metal housing and shielded design of the AFCT-711XPDZ minimizes EMI and provides excellent EMI performance. Table Regulatory Compliance Electrostatic Discharge ESD to the exterior of the XFP module Electrostatic Discharge ESD to the Optical Connector Test Method JEDEC JESD22-A114-B GR1089 Electrostatic Discharge ESD to the Optical Connector Electromagnetic Interference EMI Immunity Variation of IEC 801-2 FCC Class B CENELEC EN55022 Class B CISPR 22A VCCI Class 1 Variation of IEC 61000-4-3 Laser Eye Safety and Equipment Type Testing Component Recognition US FDA CDRH AEL Class 1 US21 CFR, Subchapter J per Paragraphs and IEC EN60825-1 1994 + A11+A2 IEC EN60825-2 1994 + A1 IEC EN60950 1992 + A1 + A2 + A3 + A4 + A11 Underwriters Laboratories and Canadian Standards Association Joint Component Recognition for Information Technology Equipment Including Electrical Business Equipment Performance 1000 Volts 10 discharges of both polarities of 8 KV on the electrical faceplate with device inserted into a panel. Air discharge of 15 kV min contact to connector w/o damage System margins are dependent on customer board and chassis design. Less than dB of Rx sensitivity degradation and less than 10% margin reduction of Tx mask at 10 V/m, 10 MHZ to 1 GHz w/o chassis enclosure CDRH certification # 9521220-100 TUV Certificate # R72071466 UL file # E173874 Eye Safety The AFCT-711XPDZ transceivers provide Class 1 eye safety by design. Avago Technologies has tested the transceiver design for regulatory compliance, under normal operating conditions and under single fault conditions. See Table Flammability The AFCT-711XPDZ is compliant to UL 94V-0. Customer Manufacturing Processes The module is pluggable and is not designed for aqueous wash, IR reflow or wave soldering processes. Caution The AFCT-711XPDZ contains no user serviceable parts. Tampering with or modifying the performance of the AFCT-711XPDZ will result in voided product warranty. It may also result in improper operation of the AFCT711XPDZ circuitry, and possible overstress of the laser source. Device degradation or product failure may result. Connection of the AFCT-711XPDZ to a non-approved optical source, operating above the recommended absolute maximum conditions may be considered an act of modifying or manufacturing a laser product. The person s performing such an act is required by law to recertify and reidentify the laser product under the provisions of U.S. 21 CFR Subchapter J and the TUV. Ordering Information Please contact your local field sales engineer or one of Avago Technologies franchised distributors for ordering information. For technical information, please visit Avago Technologies ’ WEB page at For information related to XFP MSA documentation visit xfpmsa.org For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright 2005-2008 Avago Technologies. All rights reserved. AV02-1079EN - November 26, 2008 |
More datasheets: 74LVTH543MTCX | 74LVTH543WMX | 74LVTH543WM | AT49F1024-70VI | AT49F1024-70VC | AT49F1025-70JC | AT49F1025-70JI | AT49F1024-55VC | AT49F1024-55VI | AT49F1025-55JI |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AFCT-711XPDZ Datasheet file may be downloaded here without warranties.