AFCT-701SDDZ

AFCT-701SDDZ Datasheet

AFCT-701SDDZ 10Gb/1Gb Ethernet, 1310nm SFP+ Transceiver

Part	Datasheet
AFCT-701SDDZ	AFCT-701SDDZ (pdf)

PDF Datasheet Preview
AFCT-701SDDZ 10Gb/1Gb Ethernet, 1310nm SFP+ Transceiver Data Sheet AFCT-701SDDZ The Avago AFCT-701SDDZ transceiver is part of a family of SFP+ products. This transceiver utilizes Avago’s 1310nm DFB and PIN Detector technology to provide an IEEE 10Gb Ethernet design compliant with the 10GBASELR standard and allows for the operation at 1.25GBd for Gigabit Ethernet Applications. The AFCT-701SDDZ transceiver has the signal and the chassis SFP grounds tied together to enhance the EMI shielding performance of the module, providing extra margin that is particularly useful in higher density applications. The design is based on the new electrical and mechanical specification enhancements to the well known SFP specifications developed by the SFF Committee. These specifications are referred to as SFP+ to recognize these enhancements to previous SFP specifications used for lower speed products. Avago Technologies is an active participant in the SFF Committee specification development activities. Related Products x AFBR-703SDDZ SFP+ 10Gb/1Gb Gigabit Ethernet 10GBASE-SR transceiver for operation in OM3 MMF link applications with link length up to 300 meters x AFCT-701SDZ AFCT-701ASDZ SFP+ 10 Gigabit Ethernet 10GBASE-LR transceiver with case temperature 0-70 qC 0-85 qC for operation in SMF link applications with link lengths up to 10 Km. x AFBR-707SDZ SFP+ 10 Gigabit Ethernet 10GBASELRM transceiver for 220 meter operation in all MMF link applications including OM1 and OM2 legacy fiber cables and new high bandwidth OM3 fiber cables. x AFCT-5016Z SFP+ Evaluation Board The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceivers. x Avago 1310nm Distributed Feedback DFB source and Transmitter Optical Subassembly technology x Avago PIN detector and Receiver Optical Subassembly technology x Typical power dissipation 850mW x Full digital diagnostic management interface x Avago SFP+ package design enables equipment EMI performance in high port density applications with margin to Class B limits x Flexibility in data rate selection through either hardware or software control Specifications x Optical interface specifications per IEEE 802.3ae 10GBASE-LR x Compliant to the transmitter extinction ratio and the receiver sensitivity specs per IEEE Gigabit Ethernet 1.25GBd 1000BASE-LX x Electrical interface specifications per SFF Committee SFF 8431 Specifications for Enhanced and 10 Gigabit Small Form Factor Pluggable Module “SFP+” x Management interface specifications per SFF Committee SFF 8431 and SFF 8472 Diagnostic Monitoring Interface for Optical Transceivers x Mechanical specifications per SFF Committee SFF 8432 Improved Pluggable Formfactor “IPF” x LC Duplex optical connector interface confirming to ANSI TIA/EA 604-10 FOCIS 10A x Compliant to Restriction on Hazardous Substances RoHS per EU and China requirements x Compliant to halogen free requirement x Class 1 Eye safe per requirements of IEC 60825-1/ CDRH Description, continued Installation The AFCT-701SDDZ transceiver package is compliant with the SFF 8432 Improved Pluggable Formfactor housing specification for the SFP+. It can be installed in any INF-8074 or SFF-8431/2 compliant Small Form Pluggable SFP port regardless of host equipment operating status The AFCT-701SDDZ is hot-pluggable, allowing the module to be installed while the host system is operating and on-line. Upon insertion, the transceiver housing makes initial contact with the host board SFP cage, mitigating potential damage due to Electro-Static Discharge ESD . By selecting TX rate select to Gbps operation, the TX module performance complies with the extinction ratio and output power level in the 1000BASE-LX specifications. Likewise RX performance complies with the sensitivity performance in the 1000BASE-LX by selecting RX rate select to Gbps operation. The rate select can be done through either the hardware pins or the software access to the A2h page of EEPROM map. The user can refer to the Appendix for details of rate select. Digital Diagnostic Interface and Serial Identification The two-wire interface protocol and signaling detail are based on SFF-8431. Conventional EEPROM memory, bytes 0-255 at memory address 0xA0, is organized in compliance with SFF-8431. New digital diagnostic information, bytes 0-255 at memory address 0xA2, is compliant to SFF-8472. The new diagnostic information provides the opportunity for Predictive Failure Identification, Compliance Prediction, Fault Isolation and Component Monitoring. Predictive Failure Identification The AFCT-701SDDZ predictive failure feature allows a host to identify potential link problems before system performance is impacted. Prior identification of link problems enables a host to service an application via “fail over” to a redundant link or replace a suspect device, maintaining system uptime in the process. For applications where ultra-high system uptime is required, a digital SFP provides a means to monitor two real-time laser metrics associated with laser degradation and predicting failure average laser bias current Tx_Bias and average laser optical power Tx_Power . Compliance Prediction Compliance prediction is the ability to determine if an optical transceiver is operating within its operating and environmental requirements. AFCT-701SDDZ devices provide real-time access to transceiver internal supply voltage and temperature, allowing a host to identify potential component compliance issues. Received optical power is also available to assess compliance of a cable plant and remote transmitter. When operating out of requirements, the link cannot guarantee error free transmission. Fault Isolation The fault isolation feature allows a host to quickly pinpoint the location of a link failure, minimizing downtime. For optical links, the ability to identify a fault at a local device, remote device or cable plant is crucial to speeding service of an installation. AFCT-701SDDZ realtime monitors of Tx_Bias, Tx_Power, Vcc, Temperature and Rx_Power can be used to assess local transceiver current operating conditions. In addition, status flags TX_DISABLE and Rx Loss of Signal LOS are mirrored in memory and available via the two-wire serial interface. Component Monitoring Component evaluation is a more casual use of the AFCT701SDDZ real-time monitors of Tx_Bias, Tx_Power, Vcc, Temperature and Rx_Power. Potential uses are as debugging aids for system installation and design, and transceiver parametric evaluation for factory or field qualification. For example, temperature per module can be observed in high density applications to facilitate thermal evaluation of blades, PCI cards and systems. OPTICAL INTERFACE LIGHT FROM FIBER An Evaluation Kit and Reference Designs are available to assist in evaluation of the AFCT-701SDDZ. Please contact your local Field Sales representative for availability and ordering details. Caution There are no user serviceable parts nor maintenance requirements for the AFCT-701SDDZ. All mechanical adjustments are made at the factory prior to shipment. Tampering with, modifying, misusing or improperly handling the AFCT-701SDDZ will void the product warranty. It may also result in improper operation and possibly overstress the laser source. Performance degradation or device failure may result. Connection of the AFCT-701 SDDZ to a light source not compliant with IEEE Std. 802.3ae Clause 52 and SFF-8341 specifications, operating above maximum operating conditions or in a manner inconsistent with it’s design and function may result in exposure to hazardous light radiation and may constitute an act of modifying or manufacturing a laser product. Persons performing such an act are required by law to recertify and re-identify the laser product under the provisions of U.S. 21 CFR Subchapter J and TUV. Customer Manufacturing Processes This module is pluggable and is not designed for aqueous wash, IR reflow, or wave soldering processes. Ordering Information Please contact your local field sales engineer or one of Avago Technologies franchised distributors for ordering information. For technical information, please visit Avago Technologies’ WEB page at For information related to SFF Committee documentation visit Regulatory Compliance The AFCT-701SDDZ complies with all applicable laws and regulations as detailed in Table Certification level is dependent on the overall configuration of the host equipment. The transceiver performance is offered as a figure of merit to assist the designer. Electrostatic Discharge ESD The AFCT-701SDDZ is compatible with ESD levels found in typical manufacturing and operating environments as described in Table In the normal handling and operation of optical transceivers, ESD is of concern in two circumstances. The first case is during handling of the transceiver prior to insertion into an SFP compliant cage. To protect the device, it’s important to use normal ESD handling pre-cautions. These include use of grounded wrist straps, work-benches and floor wherever a transceiver is handled. The second case to consider is static discharges to the exterior of the host equipment chassis after installation. If the optical interface is exposed to the exterior of host equipment cabinet, the transceiver may be subject to system level ESD requirements. Electromagnetic Interference EMI Equipment incorporating 10 gigabit transceivers is typically subject to regulation by the FCC in the United States, CENELEC EN55022 CISPR 22 in Europe and VCCI in Japan. The AFCT-701SDDZ enables equipment compliance to these standards detailed in Table The metal housing and shielded design of the AFCT-701SDDZ minimizes the EMI challenge facing the equipment designer. For superior EMI performance it is recommended that equipment designs utilize SFP+ cages per SFF RF Immunity Susceptibility Due to its shielded design, the EMI immunity of the AFCT-701SDDZ exceeds typical industry standards. Eye Safety The AFCT-701SDDZ provides Class 1 single fault tolerant eye safety by design and has been tested for compliance with the requirements listed in Table The eye safety circuit continuously monitors the optical output power level and will disable the transmitter upon detecting a condition beyond the scope of Class 1 certification Such conditions can be due to inputs from the host board Vcc fluctuation, unbalanced code or a fault within the transceiver. US CDRH and EU TUV certificates are listed in table Flammability The AFCT-701SDDZ optical transceiver is made of metal and high strength, heat resistant, chemical resistant and UL 94V-0 flame retardant plastic. Table Regulatory Compliance Feature Electrostatic Discharge ESD to the Electrical Contacts Electrostatic Discharge ESD to the Duplex LC Receptacle Life Traffic ESD Immunity Life Traffic ESD Immunity Electromagnetic Interference EMI RF Immunity Laser Eye Safety and Equipment Type Testing BAUART GEPRU¨ FT TU¨ V Rheinland Product Safety TYPE APPROVED Component Recognition RoHS Compliance Test Method MIL-STD883C Method JEDEC DESD22-A11-4-B IEC 61000-4-2 IEC 61000-4-2 IEC 61000-4-2 FCC Class B CENELEC EN55022 Class B CISPR 22A VCCI Class 1 IEC 61000-4-3 US FDA CDRH AEL Class 1 US21 CFR, Subchapter J per Paragraphs and Performance Class 1 > 1KV for high speed I/O pins Class 1 > 2KV for all other pins Typically, no damage occurs with 25 kV when the duplex LC connector receptacle is contacted by a Human Body Model probe. 10 contacts of 8 kV on the electrical faceplate with device inserted into a panel. Air discharge of 15 kV min. contact to connector without damage. System margins are dependent on customer board and chassis design. Typically shows no measurable effect from a 10 V/m field swept from 80MHz to 1 GHz CDRH Accession No. 9521220-158 Pending Completion IEC EN60825-1 1994 + A11 + A2 IEC EN60825-2 1994 + A1 IEC EN60950 1992 + A1 + A2 + A3 + A4 + A11 Underwriters Laboratories and Canadian Standards Association Joint Component Recognition for Information Technology Equipment including Electrical Business Equipment RoHS Directive 2002/95/EC and it’s amendment directives 6/6 UL file E173874 SGS Test Report No. LPC1/00895/08 CTS ref. CTS/08-0238/Avago TX_DISABLE TX_FAULT VeeT

PDF Datasheet Preview

AFCT-701SDDZ 10Gb/1Gb Ethernet, 1310nm SFP+ Transceiver

Data Sheet AFCT-701SDDZ

The Avago AFCT-701SDDZ transceiver is part of a family of SFP+ products. This transceiver utilizes Avago’s 1310nm DFB and PIN Detector technology to provide an IEEE 10Gb Ethernet design compliant with the 10GBASELR standard and allows for the operation at 1.25GBd for Gigabit Ethernet Applications. The AFCT-701SDDZ transceiver has the signal and the chassis SFP grounds tied together to enhance the EMI shielding performance of the module, providing extra margin that is particularly useful in higher density applications. The design is based on the new electrical and mechanical specification enhancements to the well known SFP specifications developed by the SFF Committee. These specifications are referred to as SFP+ to recognize these enhancements to previous SFP specifications used for lower speed products. Avago Technologies is an active participant in the SFF Committee specification development activities.

Related Products
x AFBR-703SDDZ SFP+ 10Gb/1Gb Gigabit Ethernet 10GBASE-SR transceiver for operation in OM3 MMF link applications with link length up to 300 meters
x AFCT-701SDZ AFCT-701ASDZ SFP+ 10 Gigabit Ethernet 10GBASE-LR transceiver with case temperature 0-70 qC 0-85 qC for operation in SMF link applications with link lengths up to 10 Km.
x AFBR-707SDZ SFP+ 10 Gigabit Ethernet 10GBASELRM transceiver for 220 meter operation in all MMF link applications including OM1 and OM2 legacy fiber cables and new high bandwidth OM3 fiber cables.
x AFCT-5016Z SFP+ Evaluation Board The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceivers.
x Avago 1310nm Distributed Feedback DFB source and Transmitter Optical Subassembly technology
x Avago PIN detector and Receiver Optical Subassembly technology
x Typical power dissipation 850mW
x Full digital diagnostic management interface
x Avago SFP+ package design enables equipment EMI performance in high port density applications with margin to Class B limits
x Flexibility in data rate selection through either hardware or software control

Specifications
x Optical interface specifications per IEEE 802.3ae 10GBASE-LR
x Compliant to the transmitter extinction ratio and the receiver sensitivity specs per IEEE Gigabit Ethernet 1.25GBd 1000BASE-LX
x Electrical interface specifications per SFF Committee SFF 8431 Specifications for Enhanced and 10 Gigabit Small Form Factor Pluggable Module “SFP+”
x Management interface specifications per SFF Committee SFF 8431 and SFF 8472 Diagnostic Monitoring Interface for Optical Transceivers
x Mechanical specifications per SFF Committee SFF 8432 Improved Pluggable Formfactor “IPF”
x LC Duplex optical connector interface confirming to ANSI TIA/EA 604-10 FOCIS 10A
x Compliant to Restriction on Hazardous Substances RoHS per EU and China requirements
x Compliant to halogen free requirement
x Class 1 Eye safe per requirements of IEC 60825-1/ CDRH

Description, continued

Installation

The AFCT-701SDDZ transceiver package is compliant with the SFF 8432 Improved Pluggable Formfactor housing specification for the SFP+. It can be installed in any INF-8074 or SFF-8431/2 compliant Small Form Pluggable SFP port regardless of host equipment operating status The AFCT-701SDDZ is hot-pluggable, allowing the module to be installed while the host system is operating and on-line. Upon insertion, the transceiver housing makes initial contact with the host board SFP cage, mitigating potential damage due to Electro-Static Discharge ESD .

By selecting TX rate select to Gbps operation, the TX module performance complies with the extinction ratio and output power level in the 1000BASE-LX specifications.

Likewise RX performance complies with the sensitivity performance in the 1000BASE-LX by selecting RX rate select to Gbps operation.

The rate select can be done through either the hardware pins or the software access to the A2h page of EEPROM map. The user can refer to the Appendix for details of rate select.

Digital Diagnostic Interface and Serial Identification

The two-wire interface protocol and signaling detail are based on SFF-8431. Conventional EEPROM memory, bytes 0-255 at memory address 0xA0, is organized in compliance with SFF-8431. New digital diagnostic information, bytes 0-255 at memory address 0xA2, is compliant to SFF-8472. The new diagnostic information provides the opportunity for Predictive Failure Identification, Compliance Prediction, Fault Isolation and Component Monitoring.

Predictive Failure Identification

The AFCT-701SDDZ predictive failure feature allows a host to identify potential link problems before system performance is impacted. Prior identification of link problems enables a host to service an application via “fail over” to a redundant link or replace a suspect device, maintaining system uptime in the process. For applications where ultra-high system uptime is required, a digital SFP provides a means to monitor two real-time laser metrics associated with laser degradation and predicting failure average laser bias current Tx_Bias and average laser optical power Tx_Power .

Compliance Prediction

Compliance prediction is the ability to determine if an optical transceiver is operating within its operating and environmental requirements. AFCT-701SDDZ devices provide real-time access to transceiver internal supply voltage and temperature, allowing a host to identify potential component compliance issues. Received optical power is also available to assess compliance of a cable plant and remote transmitter. When operating out of requirements, the link cannot guarantee error free transmission.

Fault Isolation

The fault isolation feature allows a host to quickly pinpoint the location of a link failure, minimizing downtime. For optical links, the ability to identify a fault at a local device, remote device or cable plant is crucial to speeding service of an installation. AFCT-701SDDZ realtime monitors of Tx_Bias, Tx_Power, Vcc, Temperature and Rx_Power can be used to assess local transceiver current operating conditions. In addition, status flags TX_DISABLE and Rx Loss of Signal LOS are mirrored in memory and available via the two-wire serial interface.

Component Monitoring

Component evaluation is a more casual use of the AFCT701SDDZ real-time monitors of Tx_Bias, Tx_Power, Vcc, Temperature and Rx_Power. Potential uses are as debugging aids for system installation and design, and transceiver parametric evaluation for factory or field qualification. For example, temperature per module can be observed in high density applications to facilitate thermal evaluation of blades, PCI cards and systems.

OPTICAL INTERFACE LIGHT FROM FIBER
An Evaluation Kit and Reference Designs are available to assist in evaluation of the AFCT-701SDDZ. Please contact your local Field Sales representative for availability and ordering details.

Caution

There are no user serviceable parts nor maintenance requirements for the AFCT-701SDDZ. All mechanical adjustments are made at the factory prior to shipment. Tampering with, modifying, misusing or improperly handling the AFCT-701SDDZ will void the product warranty. It may also result in improper operation and possibly overstress the laser source. Performance degradation or device failure may result. Connection of the AFCT-701 SDDZ to a light source not compliant with IEEE Std. 802.3ae Clause 52 and SFF-8341 specifications, operating above maximum operating conditions or in a manner inconsistent with it’s design and function may result in exposure to hazardous light radiation and may constitute an act of modifying or manufacturing a laser product. Persons performing such an act are required by law to recertify and re-identify the laser product under the provisions of U.S. 21 CFR Subchapter J and TUV.

Customer Manufacturing Processes

This module is pluggable and is not designed for aqueous wash, IR reflow, or wave soldering processes.
Ordering Information
Please contact your local field sales engineer or one of Avago Technologies franchised distributors for ordering information. For technical information, please visit Avago Technologies’ WEB page at For information related to SFF Committee documentation visit

Regulatory Compliance

The AFCT-701SDDZ complies with all applicable laws and regulations as detailed in Table Certification level is dependent on the overall configuration of the host equipment. The transceiver performance is offered as a figure of merit to assist the designer.

Electrostatic Discharge ESD

The AFCT-701SDDZ is compatible with ESD levels found in typical manufacturing and operating environments as described in Table In the normal handling and operation of optical transceivers, ESD is of concern in two circumstances.

The first case is during handling of the transceiver prior to insertion into an SFP compliant cage. To protect the device, it’s important to use normal ESD handling pre-cautions. These include use of grounded wrist straps, work-benches and floor wherever a transceiver is handled.

The second case to consider is static discharges to the exterior of the host equipment chassis after installation. If the optical interface is exposed to the exterior of host equipment cabinet, the transceiver may be subject to system level ESD requirements.

Electromagnetic Interference EMI

Equipment incorporating 10 gigabit transceivers is typically subject to regulation by the FCC in the United States, CENELEC EN55022 CISPR 22 in Europe and VCCI in Japan. The AFCT-701SDDZ enables equipment compliance to these standards detailed in Table The metal housing and shielded design of the AFCT-701SDDZ minimizes the EMI challenge facing the equipment designer. For superior EMI performance it is recommended that equipment designs utilize SFP+ cages per SFF

RF Immunity Susceptibility

Due to its shielded design, the EMI immunity of the AFCT-701SDDZ exceeds typical industry standards.

Eye Safety

The AFCT-701SDDZ provides Class 1 single fault tolerant eye safety by design and has been tested for compliance with the requirements listed in Table The eye safety circuit continuously monitors the optical output power level and will disable the transmitter upon detecting a condition beyond the scope of Class 1 certification Such conditions can be due to inputs from the host board Vcc fluctuation, unbalanced code or a fault within the transceiver. US CDRH and EU TUV certificates are listed in table

Flammability

The AFCT-701SDDZ optical transceiver is made of metal and high strength, heat resistant, chemical resistant and UL 94V-0 flame retardant plastic.

Table Regulatory Compliance Feature

Electrostatic Discharge ESD to the Electrical Contacts Electrostatic Discharge ESD to the Duplex LC Receptacle

Life Traffic ESD Immunity

Life Traffic ESD Immunity

Electromagnetic Interference EMI

RF Immunity

Laser Eye Safety and Equipment Type Testing

BAUART GEPRU¨ FT

TU¨ V Rheinland Product Safety

TYPE APPROVED

Component Recognition

RoHS Compliance

Test Method MIL-STD883C Method JEDEC DESD22-A11-4-B IEC 61000-4-2

IEC 61000-4-2

IEC 61000-4-2

FCC Class B CENELEC EN55022 Class B CISPR 22A VCCI Class 1 IEC 61000-4-3

US FDA CDRH AEL Class 1 US21 CFR, Subchapter J per Paragraphs and

Performance Class 1 > 1KV for high speed I/O pins Class 1 > 2KV for all other pins Typically, no damage occurs with 25 kV when the duplex LC connector receptacle is contacted by a Human Body Model probe. 10 contacts of 8 kV on the electrical faceplate with device inserted into a panel. Air discharge of 15 kV min. contact to connector without damage. System margins are dependent on customer board and chassis design.

Typically shows no measurable effect from a 10 V/m field swept from 80MHz to 1 GHz CDRH Accession No. 9521220-158 Pending Completion

IEC EN60825-1 1994 + A11 + A2 IEC EN60825-2 1994 + A1 IEC EN60950 1992 + A1 + A2 + A3 + A4 + A11

Underwriters Laboratories and Canadian Standards Association Joint Component Recognition for Information Technology Equipment including Electrical Business Equipment

RoHS Directive 2002/95/EC and it’s amendment directives 6/6

UL file E173874

SGS Test Report No. LPC1/00895/08 CTS ref. CTS/08-0238/Avago

TX_DISABLE TX_FAULT

VeeT

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AFCT-701SDDZ Datasheet file may be downloaded here without warranties.

Datasheet ID: AFCT-701SDDZ 520072