ABX00014

ABX00014 Datasheet

Code ABX00014

Part	Datasheet
ABX00014	ABX00014 (pdf)

PDF Datasheet Preview
MKR FOX 1200 Code ABX00014 MKR FOX 1200 is a powerful board that combines the functionality of the Zero and SigFox connectivity. It is the ideal solution for makers wanting to design IoT projects with minimal previous experience in networking having a low power device. You’ll get 2-year free subscription to Sigfox network with the board for up to 140 messages per day , as well as free access to Spot’it geolocation service that allows you to track the board without GPS or any extra hardware. MKR FOX 1200 has been designed to offer a practical and cost effective solution for makers seeking to add SigFox connectivity to their projects with minimal previous experience in networking. It is based on the Atmel SAMD21 and a ATA8520 SigFox module. The design includes the ability to power the board using two 1.5V AA or AAA batteries or external 5V. Switching from one source to the other is done automatically. A good 32 bit computational power similar to the Zero board, the usual rich set of I/O interfaces, low power SigFox communication and the ease of use of the Arduino Software IDE for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power 5V to the board. The Arduino MKR FOX 1200 is able to run with or without the batteries connected and has limited power consumption. Warning Unlike most Arduino & Genuino boards, the MKRFOX1200 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting. Check your area coverage on the SigFox website TECH SPECS Microcontroller SAMD21 Cortex-M0+ 32bit low power ARM MCU Board Power Supply USB/VIN Supported Batteries * 2x AA or AAA Circuit Operating Voltage 3.3V Digital I/O Pins PWM Pins 12 0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19 UART Analog Input Pins 7 ADC 8/10/12 bit Analog Output Pins 1 DAC 10 bit External Interrupts 8 0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17 DC Current per I/O Pin Flash Memory 256 KB SRAM 32 KB EEPROM Clock Speed kHz RTC , 48 MHz LED_BUILTIN Full-Speed USB Device and embedded Host LED_BUILTIN Antenna power Carrier frequency 868 MHz Working region Length Width 25 mm Weight

PDF Datasheet Preview

MKR FOX 1200

Code ABX00014

MKR FOX 1200 is a powerful board that combines the functionality of the Zero and SigFox connectivity. It is the ideal solution for makers wanting to design IoT projects with minimal previous experience in networking having a low power device. You’ll get 2-year free subscription to Sigfox network with the board for up to 140 messages per day , as well as free access to Spot’it geolocation service that allows you to track the board without GPS or any extra hardware.

MKR FOX 1200 has been designed to offer a practical and cost effective solution for makers seeking to add SigFox connectivity to their projects with minimal previous experience in networking. It is based on the Atmel SAMD21 and a ATA8520 SigFox module. The design includes the ability to power the board using two 1.5V AA or AAA batteries or external 5V. Switching from one source to the other is done automatically. A good 32 bit computational power similar to the Zero board, the usual rich set of I/O interfaces, low power SigFox communication and the ease of use of the Arduino Software IDE for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power 5V to the board. The Arduino MKR FOX 1200 is able to run with or without the batteries connected and has limited power consumption. Warning Unlike most Arduino & Genuino boards, the MKRFOX1200 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting. Check your area coverage on the SigFox website

TECH SPECS

Microcontroller

SAMD21 Cortex-M0+ 32bit low power ARM MCU

Board Power Supply USB/VIN

Supported Batteries *
2x AA or AAA

Circuit Operating Voltage
3.3V

Digital I/O Pins

PWM Pins
12 0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19

UART

Analog Input Pins
7 ADC 8/10/12 bit

Analog Output Pins
1 DAC 10 bit

External Interrupts
8 0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17

DC Current per I/O Pin

Flash Memory
256 KB

SRAM
32 KB

EEPROM

Clock Speed
kHz RTC , 48 MHz

LED_BUILTIN

Full-Speed USB Device and embedded Host

LED_BUILTIN

Antenna power

Carrier frequency
868 MHz

Working region

Length

Width
25 mm

Weight

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ABX00014 Datasheet file may be downloaded here without warranties.

Datasheet ID: ABX00014 518326