5T251S0F2100

5T251S0F2100 Datasheet

Part	Datasheet
5T251S0F2100	5T251S0F2100 (pdf)

Related Parts	Information
5S251S0F1000	5S251S0F1000

PDF Datasheet Preview
AAPEM M 5000 SERIES - POTENTIOMETER JOYSTICKS COST EFFECTIVE LOW PROFILE INSTALLATION ROHS COMPLIANT SIMPLE INTERFACE ERGONOMIC DESIGN LOW CURRENT DRAIN TWO OR THREE AXES SPECIFICALLY DESIGNED FOR KEYBOARDS 5000 SERIES - POTENTIOMETER JOYSTICKS PRODUCT DESCRIPTION GENERAL DESCRIPTION The 5000 Series is a range of low profile, cost optimised potentiometer joysticks. These joysticks are designed specifically for applications such as keyboards where installed depth and cost are critical. Configurable in up to three axes, for pan, tilt and zoom control of such applications as CCTV cameras the 5000 Series is offered with a range of handles, bezels and mounting styles. MOUNTING The 5000 Series is a sub-panel mounting joystick. It is offered with two mounting options option B allows the user to screw down from the front face of the panel, through the bezel and into the joystick. Option A has four additional screwing points on the body of the joystick, allowing the user to screw from the underside of the panel, up through the joystick and into the panel, and in so doing the screw heads are concealed. Option B is designed for use with gaiter option 1 and bezel option 2, where as option A is designed for use with bezel option POTENTIOMETERS The 5000 Series is offered as standard with 5K potentiometers which have 220° tracks. With a shaft deflection angle of nominally 40°, a typical 5V supply would therefore result in a full scale nominal deflection from 2V to 3V, operating about a nominal 2.5V centre. The potentiometers used on the 5000 Series are designed for use as a variable potential divider, rather than a two pin variable resistor. Noise generated by the contact resistance of the wiper to the track dictates that for optimum performance the output signals should be fed into a load of greater than 100K. OPERATING MODE The operating mode of the joystick may be specified as either sprung to centre, or alternatively with a “ratchet” position, allowing a positive detented feel in three positions either side of centre available on X & Y axes only . USER FLEXIBILITY The 5000 Series is designed to be as flexible as possible whilst keeping cost optimal. As standard the unit is offered without a wiring harness, allowing customers to wire the unit according to the needs of the individual application. The joystick may be factory configured with cable harnesses upon request. The 5000 Series is offered with an open square gate as standard, again allowing the customer the flexibility of determining in software how the precise control is configured. LEVERS Lever option 1 should be specified for any two axes configuration. Lever option 8 is for three axes operation. Apem offers a range of non standard lever options, including custom and lower profile options, for more detailed of these or any other 5000 Series enquiries please contact your local Apem representative. Note The company reserves the right to change specifications without notice. 5000 SERIES - POTENTIOMETER JOYSTICKS PRODUCT CONFIGURATION STANDARD OPTIONS The 5000 Series is available with a range of standard options, to specify your joystick, simply choose one option from each column. An example is shown below. SERIES MOUNTING AXES POTS LEVER SPRING WIRED HANDLE BEZEL GAITER MODIFIER 5000 5 Sub Mount A S Sub Mount B T Two 2 Three 3 5 K 220° 5 Standard 1 For 3 Axes 8 Ratchet R Standard S None 0 200mm 1 Conical F Tall Conical H Tall Slimline V Third Axis W Not supplied 0 Square 1 Circular 2 Not supplied 0 Standard 1 None 00

PDF Datasheet Preview

AAPEM M
5000 SERIES - POTENTIOMETER JOYSTICKS

COST EFFECTIVE LOW PROFILE INSTALLATION ROHS COMPLIANT SIMPLE INTERFACE ERGONOMIC DESIGN LOW CURRENT DRAIN TWO OR THREE AXES SPECIFICALLY DESIGNED FOR KEYBOARDS
5000 SERIES - POTENTIOMETER JOYSTICKS

PRODUCT DESCRIPTION

GENERAL DESCRIPTION The 5000 Series is a range of low profile, cost optimised potentiometer joysticks. These joysticks are designed specifically for applications such as keyboards where installed depth and cost are critical. Configurable in up to three axes, for pan, tilt and zoom control of such applications as CCTV cameras the 5000 Series is offered with a range of handles, bezels and mounting styles.

MOUNTING The 5000 Series is a sub-panel mounting joystick. It is offered with two mounting options option B allows the user to screw down from the front face of the panel, through the bezel and into the joystick. Option A has four additional screwing points on the body of the joystick, allowing the user to screw from the underside of the panel, up through the joystick and into the panel, and in so doing the screw heads are concealed. Option B is designed for use with gaiter option 1 and bezel option 2, where as option A is designed for use with bezel option

POTENTIOMETERS The 5000 Series is offered as standard with 5K potentiometers which have 220° tracks. With a shaft deflection angle of nominally 40°, a typical 5V supply would therefore result in a full scale nominal deflection from 2V to 3V, operating about a nominal 2.5V centre. The potentiometers used on the 5000 Series are designed for use as a variable potential divider, rather than a two pin variable resistor. Noise generated by the contact resistance of the wiper to the track dictates that for optimum performance the output signals should be fed into a load of greater than 100K.

OPERATING MODE The operating mode of the joystick may be specified as either sprung to centre, or alternatively with a “ratchet” position, allowing a positive detented feel in three positions either side of centre available on X & Y axes only .

USER FLEXIBILITY The 5000 Series is designed to be as flexible as possible whilst keeping cost optimal. As standard the unit is offered without a wiring harness, allowing customers to wire the unit according to the needs of the individual application. The joystick may be factory configured with cable harnesses upon request. The 5000 Series is offered with an open square gate as standard, again allowing the customer the flexibility of determining in software how the precise control is configured.

LEVERS Lever option 1 should be specified for any two axes configuration. Lever option 8 is for three axes operation. Apem offers a range of non standard lever options, including custom and lower profile options, for more detailed of these or any other 5000 Series enquiries please contact your local Apem representative.

Note The company reserves the right to change specifications without notice.
5000 SERIES - POTENTIOMETER JOYSTICKS

PRODUCT CONFIGURATION

STANDARD OPTIONS The 5000 Series is available with a range of standard options, to specify your joystick, simply choose one option from each column. An example is shown below.

SERIES MOUNTING AXES

POTS

LEVER SPRING WIRED HANDLE

BEZEL

GAITER MODIFIER
5000 5

Sub Mount A S

Sub Mount B T

Two 2 Three 3
5 K 220° 5

Standard 1

For 3 Axes 8

Ratchet R

Standard S

None 0
200mm 1

Conical F

Tall Conical H

Tall Slimline V

Third Axis W

Not supplied 0

Square 1

Circular 2

Not supplied 0

Standard 1

None 00

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 5T251S0F2100 Datasheet file may be downloaded here without warranties.

Datasheet ID: 5T251S0F2100 518088