AD5247BKS10-R2

AD5247BKS10-R2 Datasheet

The AD5247 provides a compact, 2 mm x mm, packaged solution for 128-position adjustment applications. This device performs the same electronic adjustment function as a mechanical potentiometer or a variable resistor. Available in four different end-to-end resistance values 5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ , these low temperature coefficient devices are ideal for high accuracy and stability variable resistance adjustments.

Part	Datasheet
AD5247BKS10-R2	AD5247BKS10-R2 (pdf)

Related Parts	Information
AD5247BKS5-R2	AD5247BKS5-R2
AD5247BKS100-R2	AD5247BKS100-R2
AD5247BKS50-R2	AD5247BKS50-R2
AD5247EVAL	AD5247EVAL

PDF Datasheet Preview
128 positions End-to-end resistance 5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ Ultracompact, SC70-6 2 mm x mm package I2C-compatible interface Full read/write of wiper register Power-on preset to midscale Single-supply V to V Low temperature coefficient 45 ppm/°C Low power, IDD = 3 uA typical Wide operating temperature range to +125°C Available in package Evaluation board available Mechanical potentiometer replacement in new designs Transducer adjustment of pressure, temperature, position, chemical, and optical sensors RF amplifier-biasing LCD brightness and contrast adjustment Automotive electronics adjustment Gain control and offset adjustment The AD5247 provides a compact, 2 mm x mm, packaged solution for 128-position adjustment applications. This device performs the same electronic adjustment function as a mechanical potentiometer or a variable resistor. Available in four different end-to-end resistance values 5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ , these low temperature coefficient devices are ideal for high accuracy and stability variable resistance adjustments. The wiper settings are controllable through the I2C-compatible digital interface, which can also be used to read back the present wiper register control word. The 10 kΩ and 100 kΩ options each 128-Position Digital Potentiometer AD5247 FUNCTIONAL BLOCK DIAGRAM A SDA I2C INTERFACE SCL WIPER REGISTER Figure have three hard-coded slave address options available to allow users access to three of these devices on one I2C bus see Table 8 for a full list of slave address locations . The resistance between the wiper and either end point of the fixed resistor varies linearly with respect to the digital code transferred into the RDAC latch. Note the terms digital potentiometer, VR variable resistor , and RDAC are used interchangeably in this document. Operating from a V to V power supply and consuming 3 uA allows the AD5247 to be used in portable battery-operated applications. 03876-001 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: Fax Analog Devices, Inc. All rights reserved. AD5247 TABLE OF CONTENTS Electrical kΩ 3 Electrical kΩ, 50 kΩ, and 100 kΩ 4 Timing kΩ, 10 kΩ, 50 kΩ, and 100 kΩ 5 Absolute Maximum 6 ESD 6 Pin Configuration and Function 7 Typical Performance Characteristics 8 Test 12 I2C 13 Theory of Operation 14 Programming the Variable 14 Programming the Potentiometer Divider............................... 15 I2C-Compatible 2-Wire Serial 15 Level Shifting for Bidirectional Interface 16 ESD Protection 16 Terminal Voltage Operating Range 16 Maximum Operating Current 16 Power-Up Sequence 16 Layout and Power Supply Bypassing 17 Constant Bias to Retain Resistance Setting............................. 17 Evaluation Board 17 Outline Dimensions 18 Ordering Guide 18 AD5247 SPECIFICATIONS ELECTRICAL kΩ VERSION VDD = 5 V ± 10% or 3 V ± 10%, VA = VDD, −40°C < TA < +125°C, unless otherwise noted. Table Parameter DC MODE Resistor Differential Nonlinearity2 Resistor Integral Nonlinearity2 Nominal Resistor Tolerance3 Resistance Temperature Coefficient3 Output Resistance DC DIVIDER MODE Differential Nonlinearity4 Integral Nonlinearity4 Voltage Divider Temperature Coefficient Full-Scale Error Zero-Scale Error RESISTOR TERMINALS Voltage Range5 Capacitance A6 Capacitance W6 Common-Mode Leakage DIGITAL INPUTS AND OUTPUTS Input Logic High Input Logic Low Input Logic High Input Logic Low Input Current Input Capacitance6 POWER SUPPLIES Power Supply Range Supply Current Power Dissipation7 Power Supply Sensitivity DYNAMIC CHARACTERISTICS6, 8 Bandwidth dB Total Harmonic Distortion VW Settling Time Resistor Noise Voltage Density Symbol Conditions Min Typ1 Max Unit R-DNL R-INL RWB RWB, VA = no connect RWB, VA = no connect Code = 0x00 −4 +4 LSB −30 +30 % ppm/°C 300 Ω DNL INL VWFSE VWZSE Code = 0x40 Code = 0x7F Code = 0x00 −1 +1 −1 +1 −3 −2 LSB ppm/°C LSB VA, VW CA f = 1 MHz, measured to GND, code = 0x40 f = 1 MHz, measured to GND, code = 0x40 VA = VDD/2 pF nA VDD = 5 V VDD = 5 V VDD = 3 V VDD = 3 V VIN = 0 V or 5 V V ±1 uA VDD RANGE VIH = 5 V or VIL = 0 V PDISS ORDERING GUIDE Model AD5247BKS5-R2 AD5247BKS5-RL7 AD5247BKSZ5-RL71 AD5247BKS10-R2 AD5247BKS10-RL7 AD5247BKSZ10-RL71 AD5247BKSZ10-1RL71 AD5247BKSZ10-2RL71 AD5247BKS50-R2 AD5247BKS50-RL7 AD5247BKSZ50-RL71 AD5247BKS100-R2 AD5247BKS100-RL7 AD5247BKSZ100-R2 AD5247BKSZ100-RL71 AD5247BKSZ100-1RL71 AD5247BKSZ100-2RL71 AD5247EVAL2 PIN 1 SEATING PLANE COPLANARITY COMPLIANT TO JEDEC STANDARDS MO-203-AB Figure 6-Lead Thin Shrink Small Outline Transistor Package [SC70] KS-6 Dimensions shown in millimeters RAB kΩ 5 10 50 100 Temperature Range to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C Package Description 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 Evaluation Board Package Option KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 1 Z = RoHS compliant part. 2 The evaluation board is shipped with the 10 kΩ RAB resistor option however, the board is compatible with all available resistor value options. Branding D1E D96 D19 D95 D5E DAK D18 D97 D17 D98 DAJ DAL NOTES AD5247 AD5247 NOTES Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C03876-0-3/07 B

PDF Datasheet Preview

128 positions End-to-end resistance 5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ Ultracompact, SC70-6 2 mm x mm package I2C-compatible interface Full read/write of wiper register Power-on preset to midscale Single-supply V to V Low temperature coefficient 45 ppm/°C Low power, IDD = 3 uA typical Wide operating temperature range to +125°C Available in package Evaluation board available

Mechanical potentiometer replacement in new designs Transducer adjustment of pressure, temperature, position,
chemical, and optical sensors RF amplifier-biasing LCD brightness and contrast adjustment Automotive electronics adjustment Gain control and offset adjustment

The AD5247 provides a compact, 2 mm x mm, packaged solution for 128-position adjustment applications. This device performs the same electronic adjustment function as a mechanical potentiometer or a variable resistor. Available in four different end-to-end resistance values 5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ , these low temperature coefficient devices are ideal for high accuracy and stability variable resistance adjustments.

The wiper settings are controllable through the I2C-compatible digital interface, which can also be used to read back the present wiper register control word. The 10 kΩ and 100 kΩ options each
128-Position Digital Potentiometer AD5247

FUNCTIONAL BLOCK DIAGRAM

A SDA

I2C INTERFACE SCL

WIPER REGISTER

Figure
have three hard-coded slave address options available to allow users access to three of these devices on one I2C bus see Table 8 for a full list of slave address locations . The resistance between the wiper and either end point of the fixed resistor varies linearly with respect to the digital code transferred into the RDAC latch. Note the terms digital potentiometer, VR variable resistor , and RDAC are used interchangeably in this document. Operating from a V to V power supply and consuming 3 uA allows the AD5247 to be used in portable battery-operated applications.
03876-001

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel:

Fax Analog Devices, Inc. All rights reserved.

AD5247

TABLE OF CONTENTS

Electrical kΩ 3 Electrical kΩ, 50 kΩ, and 100 kΩ 4 Timing kΩ, 10 kΩ, 50 kΩ, and 100 kΩ 5 Absolute Maximum 6 ESD 6 Pin Configuration and Function 7 Typical Performance Characteristics 8 Test 12 I2C 13
Theory of Operation 14 Programming the Variable 14 Programming the Potentiometer Divider............................... 15 I2C-Compatible 2-Wire Serial 15 Level Shifting for Bidirectional Interface 16 ESD Protection 16 Terminal Voltage Operating Range 16 Maximum Operating Current 16 Power-Up Sequence 16 Layout and Power Supply Bypassing 17 Constant Bias to Retain Resistance Setting............................. 17 Evaluation Board 17
Outline Dimensions 18 Ordering Guide 18

AD5247

SPECIFICATIONS

ELECTRICAL kΩ VERSION

VDD = 5 V ± 10% or 3 V ± 10%, VA = VDD, −40°C < TA < +125°C, unless otherwise noted.

Table Parameter DC MODE

Resistor Differential Nonlinearity2 Resistor Integral Nonlinearity2 Nominal Resistor Tolerance3 Resistance Temperature Coefficient3 Output Resistance DC DIVIDER MODE Differential Nonlinearity4 Integral Nonlinearity4 Voltage Divider Temperature Coefficient Full-Scale Error Zero-Scale Error RESISTOR TERMINALS Voltage Range5 Capacitance A6

Capacitance W6

Common-Mode Leakage DIGITAL INPUTS AND OUTPUTS

Input Logic High Input Logic Low Input Logic High Input Logic Low Input Current Input Capacitance6 POWER SUPPLIES Power Supply Range Supply Current Power Dissipation7 Power Supply Sensitivity

DYNAMIC CHARACTERISTICS6, 8 Bandwidth dB Total Harmonic Distortion VW Settling Time Resistor Noise Voltage Density

Symbol Conditions

Min Typ1 Max Unit

R-DNL R-INL RWB

RWB, VA = no connect RWB, VA = no connect

Code = 0x00
−4 +4 LSB
−30
+30 %
ppm/°C
300 Ω

DNL INL VWFSE VWZSE

Code = 0x40 Code = 0x7F Code = 0x00
−1 +1
−1 +1
−3 −2

LSB ppm/°C LSB

VA, VW CA
f = 1 MHz, measured to GND, code = 0x40
f = 1 MHz, measured to GND, code = 0x40

VA = VDD/2
pF nA

VDD = 5 V

VDD = 5 V

VDD = 3 V

VDD = 3 V

VIN = 0 V or 5 V

V ±1 uA

VDD RANGE

VIH = 5 V or VIL = 0 V

PDISS
ORDERING GUIDE

Model AD5247BKS5-R2 AD5247BKS5-RL7 AD5247BKSZ5-RL71 AD5247BKS10-R2 AD5247BKS10-RL7 AD5247BKSZ10-RL71 AD5247BKSZ10-1RL71 AD5247BKSZ10-2RL71 AD5247BKS50-R2 AD5247BKS50-RL7 AD5247BKSZ50-RL71 AD5247BKS100-R2 AD5247BKS100-RL7 AD5247BKSZ100-R2 AD5247BKSZ100-RL71 AD5247BKSZ100-1RL71 AD5247BKSZ100-2RL71 AD5247EVAL2

PIN 1

SEATING PLANE

COPLANARITY

COMPLIANT TO JEDEC STANDARDS MO-203-AB

Figure 6-Lead Thin Shrink Small Outline Transistor Package [SC70] KS-6

Dimensions shown in millimeters

RAB kΩ 5 10 50 100

Temperature Range to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C to +125°C

Package Description 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 6-lead SC70 Evaluation Board

Package Option KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6 KS-6
1 Z = RoHS compliant part. 2 The evaluation board is shipped with the 10 kΩ RAB resistor option however, the board is compatible with all available resistor value options.

Branding D1E D96 D19 D95 D5E DAK D18 D97 D17 D98 DAJ DAL

NOTES

AD5247

AD5247 NOTES

Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.

Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.

C03876-0-3/07 B

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AD5247BKS10-R2 Datasheet file may be downloaded here without warranties.

Datasheet ID: AD5247BKS10-R2 517699