MK-GT380B

MK-GT380B Datasheet

This document provides hardware and electrical documentation for the Controller Board Rev. B, part number CB-GT380. This is the same LCD controller board integrated with the LCD Starter Kit STK-GT380 and the LCD Module Kit MK-GT380 . References to software in this document refer to the Amulet HTMLCompiler. For software documentation please see:

Part	Datasheet
MK-GT380B	MK-GT380B (pdf)

PDF Datasheet Preview
CB-GT380 Hardware Specifications Figure CB-GT380 Controller Board, Component Side. PCB Size LCD: Dot Pitch Dot Size Touch Panel: x Not including tabs Chip-on-Board, x 71.5mm diagonal 320 x 240, monochrome, black on white or blue on white Viewable area x 59.58mm Viewing Direction 6 o’clock x 0.24mm x 0.22mm 4-wire resistive analog active area is 78 x 59mm utilizes full 320 x NOTE Since the touch panel is touch activated, do NOT allow your mounting hardware to apply any compression forces inside the active area! Backlight: LED, brightness adjustable via digital pot. Contrast: Adjustable via digital pots, Temp compensated Operating Temp -20° to 70°C Storage Temp. -30° to 80°C Power: 5V +/- 10% 250mA SRAM: 128k-Bytes Flash: 512k-Bytes 448k-Bytes available Serial Port: RS-232, 9-pin DIN, up to Kbps Table PCB Specs RS232 Transceiver Enable/Disable Square to Round Enable Round to Round Disable Crystal Frequency Table Setup Freq. 10Mhz 12Mhz 16Mhz 20Mhz JP1 JP2 OPEN SHORT OPEN SHORT Note Board is loaded with 16MHZ Crystal. Crystal must be 18-20pf in a HCM49, CSM-7 or equivalent package JRXD / JTXD Can be jumpered on the board or On J2. Jumper for J8 RS232 Transceiver operation or leave open and connect directly to the Amulet’s UARTJ2 pins 8 and 10 Figure Jumper Location Boot M Float = Program Mode GND = Normal Mode Flash Baud Rate Float = 115200bps GND = 19200bps T_CAL Float = Calibration GND = Normal J2 Interface Header Pin # 1 2 3 4 5 6 7 8 9 10 11 Signal GND 5V GND Boot M RXD TXD R1OUT UART IN T1IN UART OUT

PDF Datasheet Preview

CB-GT380 Hardware Specifications

Figure CB-GT380 Controller Board, Component Side.

PCB Size LCD:

Dot Pitch Dot Size Touch Panel:
x Not including tabs

Chip-on-Board, x 71.5mm diagonal 320 x 240, monochrome, black on white or blue on white Viewable area x 59.58mm Viewing Direction 6 o’clock
x 0.24mm
x 0.22mm
4-wire resistive analog active area is 78 x 59mm utilizes full 320 x NOTE Since the touch panel is touch activated, do

NOT allow your mounting hardware to apply any compression forces inside the active area!

Backlight:

LED, brightness adjustable via digital pot.

Contrast:

Adjustable via digital pots, Temp compensated

Operating Temp -20° to 70°C

Storage Temp. -30° to 80°C

Power:
5V +/- 10% 250mA

SRAM:
128k-Bytes

Flash:
512k-Bytes 448k-Bytes available

Serial Port:

RS-232, 9-pin DIN, up to Kbps

Table PCB Specs

RS232 Transceiver Enable/Disable Square to Round Enable Round to Round Disable

Crystal Frequency Table Setup

Freq. 10Mhz 12Mhz 16Mhz 20Mhz

JP1 JP2 OPEN SHORT OPEN SHORT

Note Board is loaded with 16MHZ Crystal. Crystal must be 18-20pf in a HCM49, CSM-7 or equivalent package

JRXD / JTXD Can be jumpered on the board or On J2. Jumper for J8 RS232 Transceiver operation or leave open and connect directly to the Amulet’s UARTJ2 pins 8 and 10

Figure Jumper Location

Boot M Float = Program Mode GND = Normal Mode

Flash Baud Rate Float = 115200bps GND = 19200bps

T_CAL Float = Calibration GND = Normal

J2 Interface Header

Pin # 1 2 3 4
5 6 7 8 9 10 11

Signal GND 5V GND

Boot M

RXD TXD R1OUT UART IN T1IN UART OUT

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MK-GT380B Datasheet file may be downloaded here without warranties.

Datasheet ID: MK-GT380B 517656