96PSR-A800WCR

96PSR-A800WCR Datasheet

Part	Datasheet
96PSR-A800WCR	96PSR-A800WCR (pdf)

PDF Datasheet Preview
GENERAL SCOPE This specification describes the performance characteristic of a 800W AC-DC switching redundant power supply. The power supply shall be able to operate as a single supply, or in a 1+1 parallel hot-plug able operation with active load sharing in a 1+1 redundant configuration. Mechanical Overview The physical size of the power supply enclosure is intended to accommodate the power range of up to 800W. The physical size is 83.8mm x 76mm x 250mm height x width x length . Figure 1 Power Supply Dimension LED Marking and Identification The power supply shall have two LED for indication of the power supply status. Table 1 LED Status Information Power supply condition Output ON and OK No AC power to all power supplies AC present/only standby output on AC cord unplugged or AC power lost with a second power supply in parallel still with AC input power. Power supply warning events where the power supply continues to operate high temp, high power, high current, slow fan. Power supply critical event causing a shutdown failure OCP, OVP, UVP Power supply critical event causing a shutdown failure OTP, Fan Fail Power supply FW update mode of Module Power supply FW update mode of Housing Power supply LED Solid Green OFF 1Hz Blink Green Solid Amber 1Hz Blink Amber 1Hz Blink Green Solid Amber 2Hz Blink Green 1Hz Blink Green Environmental Requirements The power supply shall operate within all specified limits over specified conditions in The defined operation condition include temperature, humidity, altitude, shock and vibration. Temperature and Humidity Requirements The power supply shall operate within all specified limits over Top temperature range and specified humidity Range. All airflow shall pass through the power supply and not over the exterior surfaces of the power supply. The power supply shall withstand thermal storage specified in Tnon-OP without any damage. Table 2 Temperature Requirements Item TOP Tnon-OP HOP Hnon-OP Description Operating temperature range. Non-Operating temperature range. Operating humidity range, non condensing Non-Operating humidity range, non condensing MIN MAX Unit Altitude Requirements The power supply shall operate within all specified limits over Aop Altitude range. The change pressure condition shall not harm the power supply and the operation within specified regulations shall be assured. The power supply shall withstand Altitude storage specified in Anon-OP without any damage. Table 3 Altitude Requirements Item AOP Anon-OP Description Operating Altitude range. Non-Operating Altitude range. MIN MAX Unit 5000 15000 ELECTRICAL PERFORMANCE AC power Input Specification AC Inlet connector The power supply shall incorporate an AC input connector complying to IEC 320 C-14 power inlet connector specification. This inlet shall be rated for operation at 10A/250VAC. Input voltage and frequency specification The power supply shall operate within all specified limits over the following input range. Harmonic distortions of up to 10% of the rated line voltage must not cause the power supply to go out of specified limits. The power supply shall power off if the AC input is below VAClow_limit and shall start auto recover if VACrecover is reached. Input of VAC below VACrecover shall not cause any damage to the power supply, including the input fuse. The power supply shall supply the full output power in the voltage range of 90VAC to 264VAC. Table 4 Rated output power for each input voltage range Parameter 115 VAC 230 VAC Frequency Minimum input 90Vrms 180Vrms 47Hz Rated Input 100-127Vrms 200-240Vrms 50/60Hz Maximum input 140Vrms 264Vrms 63Hz

PDF Datasheet Preview

GENERAL SCOPE

This specification describes the performance characteristic of a 800W AC-DC switching redundant power supply. The power supply shall be able to operate as a single supply, or in a 1+1 parallel hot-plug able operation with active load sharing in a 1+1 redundant configuration. Mechanical Overview The physical size of the power supply enclosure is intended to accommodate the power range of up to 800W. The physical size is 83.8mm x 76mm x 250mm height x width x length .

Figure 1 Power Supply Dimension

LED Marking and Identification The power supply shall have two LED for indication of the power supply status.

Table 1 LED Status Information

Power supply condition

Output ON and OK

No AC power to all power supplies

AC present/only standby output on AC cord unplugged or AC power lost with a second power supply in parallel still with AC input power. Power supply warning events where the power supply continues to operate high temp, high power, high current, slow fan. Power supply critical event causing a shutdown failure OCP, OVP, UVP Power supply critical event causing a shutdown failure OTP, Fan Fail Power supply FW update mode of Module

Power supply FW update mode of Housing

Power supply LED Solid Green OFF 1Hz Blink Green Solid Amber
1Hz Blink Amber
1Hz Blink Green

Solid Amber 2Hz Blink Green 1Hz Blink Green

Environmental Requirements

The power supply shall operate within all specified limits over specified conditions in The defined operation condition include temperature, humidity, altitude, shock and vibration.

Temperature and Humidity Requirements The power supply shall operate within all specified limits over Top temperature range and specified humidity Range. All airflow shall pass through the power supply and not over the exterior surfaces of the power supply.

The power supply shall withstand thermal storage specified in Tnon-OP without any damage. Table 2 Temperature Requirements

Item TOP Tnon-OP HOP Hnon-OP

Description Operating temperature range. Non-Operating temperature range. Operating humidity range, non condensing Non-Operating humidity range, non condensing

MIN MAX Unit

Altitude Requirements

The power supply shall operate within all specified limits over Aop Altitude range. The change pressure condition shall not harm the power supply and the operation within specified regulations shall be assured.

The power supply shall withstand Altitude storage specified in Anon-OP without any damage. Table 3 Altitude Requirements

Item AOP Anon-OP

Description Operating Altitude range. Non-Operating Altitude range.

MIN MAX Unit
5000
15000

ELECTRICAL PERFORMANCE

AC power Input Specification

AC Inlet connector The power supply shall incorporate an AC input connector complying to IEC 320 C-14 power inlet connector specification. This inlet shall be rated for operation at 10A/250VAC.

Input voltage and frequency specification The power supply shall operate within all specified limits over the following input range. Harmonic distortions of up to 10% of the rated line voltage must not cause the power supply to go out of specified limits.

The power supply shall power off if the AC input is below VAClow_limit and shall start auto recover if VACrecover is reached. Input of VAC below VACrecover shall not cause any damage to the power supply, including the input fuse.

The power supply shall supply the full output power in the voltage range of 90VAC to 264VAC.

Table 4 Rated output power for each input voltage range

Parameter 115 VAC 230 VAC Frequency

Minimum input 90Vrms 180Vrms 47Hz

Rated Input 100-127Vrms 200-240Vrms
50/60Hz

Maximum input 140Vrms 264Vrms 63Hz

More datasheets: AD9709-EBZ | AD9763-EBZ | AD9767-EBZ | PY-1 | 2N3391A | 2N3392 | 2N3390_D75Z | 2N3393_D26Z | 2N3390 | 2N3393

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 96PSR-A800WCR Datasheet file may be downloaded here without warranties.

Datasheet ID: 96PSR-A800WCR 515651